The best tip ever...You have the two cans (primer and adhesive) taped together making them less likely to tip over and spill. Brilliant! I have knocked over so many cans over the years it isn't funny. I will be taping my cans together from now on! I usually buy adhesive and primer the old fashioned way: One can of each to knock over under the house, and a second set of cans to glue my pipes together, ha ha. This trick will cut my purchase price in half!!
This works perfect.I fought with an old 3/4" brass barbed fitting for a few days fighting leaks. I bought a plastic 3/4" barb fitting, knocked it into the poly pipe, installed a hose clamp and no more leaks. Thank you.
You are correct, I could have used a female adapter. When I transition from PVC to other pipe types, especially galvanized, I usually like to use bushings with a coupling. That way instead of a female adapter being the weakest point of the transition, the coupling with bushings becomes the strongest point. Also if you over tighten a female adapter you can spread the threads or stress the fitting enough that it will fail later.
1. Not sure what you mean by a PCP adapter. 2. I identify the 3/4" insert male adapter at 1:29 in the video and it is annotated at 5:12 in the video. 3. If a clamp is not used to tighten the poly pipe against the insert adapter, the fitting will leak or the pipe will blow off the fitting. 4. Primer takes the sheen off the pipe, cleans the pipe, and softens the pipe for a good chemical bond. 5. Clear glue is a good glue to use in PVC applications, I just prefer to use blue glue.
Thanks. Do you have a list of these parts? I am connecting 1.5" polypropylene sink trap tailpiece to 1" HDPE pipe and Oatey does not make a cement... Or, I'll take notes and convert. Thanks again.
WD-40 is a water displacer (hence, the "WD" in the product name). I use a heat gun. Works great every time! Don't over-heat the poly pipe though... 10 seconds or so is all it takes, and keep the end of the heat gun moving. Don't leave it on any one spot too long.
Had to hook up water pipe for my mobile home inspection.... I used a 3/4 polybutylene to 3/4 pvc sharkbite brass press in type adapter grey on one side (poly)and yellow on the other (cpvc)...then a stick of cpvc to another coupler which is a 3/4 to 3/4 cpvc to pvc adapter....then you just hook up your white pvc pipe to the big end of that small coupler!!! It just cost me like $18 and some change at home depot cause I bought a sharkbite coupler disconnect tool... Make sure the sharkbite coupler is grey on one side and yellowish on the other side.. Have any questions...hit me up...
Great information! If I can't find the pieces I need at HD, there is an irrigation store in the area that would have it. Hopefully this info is helpful to other viewers for locations to research in their areas.
+Lee Stensrud After doing a web search it looks like Lowes carries more of the fittings than Home Depot. Here's a link that might help: www.lowes.com/Search=poly+insert+fitting?storeId=10151&langId=-1&catalogId=10051&N=0&newSearch=true&Ntt=poly+insert+fitting#! A lot of sprinkler supply stores carry them also. If your in the Salt Lake valley you could try Peterson Plumbing Supply, Sprinkler World, Mountain States Supply, or England Plumbing.
We've used that same setup 2 times and both have leaked a few years later, always from where that hose clamp is. Those are meant for soft rubber hoses, not hard, and not supposed to be underground.
Just use a compression adapter, all you do is glue it in to your pvc and slide your poly tube into the compression adapter and done. You can get the compression adapter from irrigation companies on line, they have 1/2", 3/4" etc. The 1/2" compression adapter is only about 20 cents a piece.
Hi any idea how I can go from 1/2 cpvc to aquarium air line tubing? I want to install a drip system for my aquarium but can't figure out how to properly tap into the cpvc without leaks
One way is to drill a hole directly into the CPVC pipe and thread the hole to accept your air line tubing valve. You could also try and find a threaded bushing that would from 1/2" cpvc to 1/4" FIPT (Female Iron Pipe Thread). Then thread a valve with a 1/4" MIPT threads into the bushing that has an outlet for the drip system, similar to the valves in this link: www.drsfostersmith.com/product/prod_display.cfm?pcatid=8165&cmpid=03cseYY&gclid=CjwKEAjw7svABRCi_KPzoPr53QoSJAABSvxfLGxoTL-6W6lR6pDZweDYg00oPOF1Ny1ftV3kou_AhBoCR07w_wcB
Thank you for all of the great sprinkler videos. Is there a good reason to use pvc vs polypipe for yard irrigation? The house we just moved into has polypipe throughout the yard, a lot even above ground. I need to trench and bury everything that’s above ground. Would it be beneficial to convert to pvc while I’m at it?
Great video, thank you. This helped greatly. Quick question; what glue/primer do you use? I found some old primer in my garage, but what glue do you use? I am thinking of buying Christy's Red Hot Blue glue, is that OK? The brand of primer in my garage is Christy's.
Good video! I am about to transition some lines the same way. Isn't it possible to buy a poly male adapter that transitions in one solid piece to fit the pvc pipe?
+Rodney Morton You could use a Pex male adapter on the Pex pipe and a PVC female adapter on the PVC pipe, although on the PVC side I would use a coupling and threaded bushing instead of a female adapter. It's too easy to crack or stretch the threads on a PVC female adapter. Be aware that PVC pipe is not rated for hot water, but CPVC is.
+Daniel Johns I've never had good luck using PVC male or female adapters. They split and crack too easily. That's why I went with a PVC 1" x 3/4" bushing (Slip x Thread) glued into a 1" coupling, then a 1" x 3/4" bushing (Slip x Slip) glued into the opposite end of the 1" coupling. It makes the transition much stronger.
It should say on the if it's recommended for plastic threaded connections. My favorites are Blue Magic Pipe Joint Compound and Oatey Great White Pipe Joint Compound.
If you're transitioning from PVC to Poly pipe make sure the PVC pipe is the same size or a size bigger than the Poly pipe. Also use as few elbows as possible when connecting the pipes.
@Webkraller First off..don't use wd-40 if this maybe for a fresh water that feeds into your house.. that's not good.. 2nd use what's called a ford coupling..its compression so all u will need is 2 channel locks and about 3mins of your day....
I believe I've tried to do this, using only a double ended barbed fitting (there was a leak in the poly pipe, so we removed a small section, maybe 3/4"). But I can't get the hose clamps tight enough to keep the repair from leaking. This poly line is buried ~ 2', and services a frost free hydrant, so I'm assuming it has a moderate to high pressure. We need help soon, this is part of lawn sprinkler system, and we need to water soon. :( Thank you!
You may need to cut out a bigger section and use 2 barbed couplings for the repair. Take a 2’ piece of new pipe and push the couplings into each end. Dish soap on the fittings and inside the pipe make this easier. Make sure the pipe pushes onto the almost the center of each coupling. Then I would use 2 hose clamps on each coupling. Instead of a screwdriver try a small ratchet and 5/16” socket to tighten the hose clamps. Careful not to strip out the hose clamps. Next push one end of the 2’ piece of repair pipe with coupling into your pipe in the ground. Remember the soap. Then line up the other end with the end of the pipe in the ground. Make a cut if needed. Slide 2 hose clamp over the pipe in the ground. Put a slight bow in the 2’ piece of pipe to get the last coupling started. Push in and tighten the last 2 pipe clamps. I hope this helps and let me know if it works.
Please explain your tech with putting primer on afterwards. The primer is purple right? Im not a plumber and I don't know if I've been doing it wrong. I always put the primer (purple stuff) on then wait about 20 sec then put glue on both sides then wait 20 sec then twist together. Am I doing it wrong? Somebody Please!
+Phlop Alopagus Waiting on the primer is okay but you want to assemble the glue joints immediately after applying the glue. 20 seconds is too long to wait on some fast set glue types.
Black poly pipe has a different OD than PVC, that's why you need the barb to male adapter fitting to make the transition. What kind of compression fitting are you referring to?
Hmmm. Not so sure about that. Are you saying the ID of a plastic insert fitting is less than a metal one? The OD would have to be the same to fit the poly tubing.
+Chad warhold I don't think a PEX fitting would work on Poly pipe. 3/4" PEX pipe has an OD (outside diameter) of 0.875" and an ID (inside diameter) of 0.681". 3/4" 160psi Poly pipe has and OD of 0.916" and an ID of 0.824". The inside and outside diameters of the pipes would need to be the same for a PEX fitting to work on Poly pipe. I would use a poly insert barb adapter.
Much too complicated. Use a DIG #207 (1/2") or #5707 (3/4) into a PVC connector, glue the connector to the PVC and insert .700 poly drip. Clean and simple.
I was trying to figure out the same thing. Usually the hoses are heated with a gun, very hot water (boiling) or in a pinch just laying it out on the concrete on a hot summers day (10-15min). It's never easy to get them on but it makes a huge difference. WD40 though...
Same type of plastic is used in the automotive industry, fuel tanks, fuel lines. So any spray lubricant isn't harmful to the plastic. And you don't run the risk of melting the line by using a heat source and weakin the plastic.
Yes, most drip circuits operate at 30psi so I would install a pressure reducer with a filter. I like the Rain Bird part# PRF-075-RBY. It is a combination pressure reducer & filter.
I have a poly pipe 1" just like this, and I need connect to a PVC pipe that will be under ground, is that ok use 1 1/2 after? (1" poly pipe to 1 1/2" PVC pipe 40) It works? Will I loose pression? Thks guys 🙆
Glue a 1-1/2" coupling onto the 1-1/2" PVC pipe then glue a 1-1/2" x 1" bushing SxT (Slip x Thread) into the coupling. Thread a 1" insert male adapter into the bushing. Use teflon paste or thread tape on the male adapter.
@@Iscaper thank you, my concerns is about the sizes. My source is coming in a 1" poly pipe, I don't have a lot of pressure in this poly pipe, so, is okay connect in a 1 1/2" PVC pipe after 1" poly pipe? 1 1/4 should be better? Or I can go with 1" PVC pipe? It's because I never saw videos here with people using 1" PVC , I don't know if it's good. Thank for your help
@@ellies1877 If your supply line to the sprinklers is 1" poly you would be fine using 1" PVC pipe. I prefer PVC pipe and fittings over poly pipe and fittings in my sprinkler work.
The automotive industry has been using the same plastic for fuel tanks and fuel lines for over 3 decades now, so a little spray lubricant isn't going to harm the plastic water lines.
Instead of the lubricant on the barb, I recommend using a lighter to gently heat the end of the poly pipe so that it slightly softens so the barb enters it easily. Then use a pinch clip, not hose clamp, to secure.
In video, 3/4" poly pipe is connected to 3/4" Schedule 40 PVC pipe. If you want to connect 3/4" poly to 1/2" PVC pipe, glue a 3/4" x 1/2" bushing (Slip x Slip) into the 3/4" coupling.
With non pressure pipes like drain lines primer isn't required with Christy's. I like to use primer with pressurized pipe and fittings because the primer removes the sheen, cleans, and softens so that there is a good chemical bond after applying the glue.
You could use a poly insert 3/4" male adapter for the poly pipe, and attach a 3/4" FIPT x 3/4" MHT adapter to the poly insert male adapter. Attach your garden hose to this adapter. Here's a link: www.homedepot.com/p/Everbilt-3-4-in-MHT-x-3-4-in-FIP-Brass-Adapter-Fitting-801759/300096107
@@schoolboy405 Use a 1" poly insert female adapter for the poly pipe. Install a 1" MIPT x 3/4" MHT adapter into the female adapter. Here's a couple of links that might help: www.amazon.com/dp/B0BHSVJYKQ/ref=sspa_dk_detail_2?pd_rd_i=B0BHSVJYKQ&pd_rd_w=VIBCW&content-id=amzn1.sym.f734d1a2-0bf9-4a26-ad34-2e1b969a5a75&pf_rd_p=f734d1a2-0bf9-4a26-ad34-2e1b969a5a75&pf_rd_r=H5CAYHHJ9GRX9HTA8T1A&pd_rd_wg=jSWOL&pd_rd_r=05870e2d-a7f0-43f0-8066-18f1827d034f&s=hi&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWw&th=1 www.sprinklerwarehouse.com/poly-insert-female-adapter-1-in-x-1-in-fipt-x-insert?gad=1&gclid=CjwKCAjw6p-oBhAYEiwAgg2PgrNDU1pa1Qf0WjMxXytCZKV2ZkCJ8uHU2rmYEuUdUG8rmh0Lx4B58RoCWwgQAvD_BwE
+Alan Fox Most fittings for PVC are IPS (Iron Pipe Size), so if you can get a fitting for the ductile iron in IPS size the connection to PVC should work.
+Alan Fox I've done galvanized to PVC transitions with good luck but not ductile iron. The only ductile iron I've worked with was larger size (6") for water mains. The transition fittings are the key. The weak point from a rigid piping like galvanized or ductile iron to PVC is the transition fittings. I don't use male or female adapters in PVC because it's too easy to split or crack them. I like to use threaded bushings with couplings to make the transition fittings stronger. For example, if you have a 1" IPS male adapter fitting on the ductile iron end, I would use a 1-1/4 x 1" PVC threaded bushing with 1-1/4" PVC coupling and a 1-1/4" x 1" PVC slip coupling. Glue the bushings into the 1-1/4" coupling. The threaded end of the bushing would then be threaded onto the ductile iron adapter and the opposite end would accept 1" PVC pipe.
That metal threaded pipe insert creates a bottle neck in the pipe, essentially reducing it to 1/2." The stainless steal clamp will rust away. The WD-40 can't be good for the plastic materials, spit is better. Have a nice day.
You need a threaded IPS fitting to make the transition from insert to PVC. The way you describe would leak and water pressure would blow the insert fitting out of the PVC fitting.
Where the FUCK do you find those male to barb fittings?? I mean why THE FUCK is that the holy graile of fittings? I go to Home Depot/Lowes/Ace and ask them for a threaded male pvc to barb fitting and its like I asked them direction to the fountain of youth. PLEASE PLEASE PLEASE give a good source for those fittings. Thank you.
+XCyclonusX They may not know what you're talking about. You need to ask for Poly Insert Fittings for Poly Pipe. I went to the Home Depot and Lowes websites and typed "Poly Insert Fitting" into their search box and did get results. Home Depot only had a few, but Lowes had a number of the fittings. The Ace website showed no results for poly insert fittings. Here's a link to the Lowes site: www.lowes.com/Search=poly+insert+fitting?storeId=10151&langId=-1&catalogId=10051&N=0&newSearch=true&Ntt=poly+insert+fitting#!
Only problem with that is the ones I found at HD/and Lowes are for threading into metal female adapters. They don't thread into pvc female fittings and they don't have the slip x barb. Thanks though for understanding my frustration. I can always get what I want from Amazon but with a minimum of a 5 day shipping wait I need to get it right the first time, and with shipping its like 10x more than I'd pay from a local store.
+XCyclonusX The poly insert adapters work on both galvanized and PVC female fittings because the fittings are IPS thread. This 3/4" insert male adapter from Lowes: www.lowes.com/pd_22539-322-350407___?productId=3455128&pl=1&Ntt=poly+insert+fitting will work on a galvanized or PVC female adapter.
this looks very very unnecessary! 3/4 barbed edge to 1/2 inch female adapter. attached to flex pipe. then attached to 3/4 barbed edge to 1/2 inch male adapter. Oh ya heat the ends of the flex pipe then insert the barbed ends along with the clamps.
Хобби
![Sean Rii, Karyon, Sharzkii - Taungule [My Love] (Official Music Video)](http://i.ytimg.com/vi/eJoMuypbSzQ/mqdefault.jpg)
The best tip ever...You have the two cans (primer and adhesive) taped together making them less likely to tip over and spill. Brilliant! I have knocked over so many cans over the years it isn't funny. I will be taping my cans together from now on! I usually buy adhesive and primer the old fashioned way: One can of each to knock over under the house, and a second set of cans to glue my pipes together, ha ha. This trick will cut my purchase price in half!!
Great, thanks for watching.
This works perfect.I fought with an old 3/4" brass barbed fitting for a few days fighting leaks. I bought a plastic 3/4" barb fitting, knocked it into the poly pipe, installed a hose clamp and no more leaks. Thank you.
Great, thanks for the information.
Thank you for creating this tutorial! Hope you are safe and well.
You are correct, I could have used a female adapter. When I transition from PVC to other pipe types, especially galvanized, I usually like to use bushings with a coupling. That way instead of a female adapter being the weakest point of the transition, the coupling with bushings becomes the strongest point. Also if you over tighten a female adapter you can spread the threads or stress the fitting enough that it will fail later.
1. Not sure what you mean by a PCP adapter. 2. I identify the 3/4" insert male adapter at 1:29 in the video and it is annotated at 5:12 in the video. 3. If a clamp is not used to tighten the poly pipe against the insert adapter, the fitting will leak or the pipe will blow off the fitting. 4. Primer takes the sheen off the pipe, cleans the pipe, and softens the pipe for a good chemical bond. 5. Clear glue is a good glue to use in PVC applications, I just prefer to use blue glue.
Thanks. Do you have a list of these parts? I am connecting 1.5" polypropylene sink trap tailpiece to 1" HDPE pipe and Oatey does not make a cement... Or, I'll take notes and convert. Thanks again.
Incredibly beneficial video! THANK YOU. It's exactly what I needed to know.
+GetRhythm2011
Thanks for watching.
I did all this but from the flex tubing to the gray fitting I have a small drop leak.
WD-40 is a water displacer (hence, the "WD" in the product name). I use a heat gun. Works great every time! Don't over-heat the poly pipe though... 10 seconds or so is all it takes, and keep the end of the heat gun moving. Don't leave it on any one spot too long.
Thanks for the tip.
Had to hook up water pipe for my mobile home inspection....
I used a 3/4 polybutylene to 3/4 pvc sharkbite brass press in type adapter grey on one side (poly)and yellow on the other (cpvc)...then a stick of cpvc to another coupler which is a 3/4 to 3/4 cpvc to pvc adapter....then you just hook up your white pvc pipe to the big end of that small coupler!!!
It just cost me like $18 and some change at home depot cause I bought a sharkbite coupler disconnect tool...
Make sure the sharkbite coupler is grey on one side and yellowish on the other side..
Have any questions...hit me up...
Great video!!!Thanks
Great information! If I can't find the pieces I need at HD, there is an irrigation store in the area that would have it.
Hopefully this info is helpful to other viewers for locations to research in their areas.
+Lee Stensrud
After doing a web search it looks like Lowes carries more of the fittings than Home Depot. Here's a link that might help: www.lowes.com/Search=poly+insert+fitting?storeId=10151&langId=-1&catalogId=10051&N=0&newSearch=true&Ntt=poly+insert+fitting#! A lot of sprinkler supply stores carry them also. If your in the Salt Lake valley you could try Peterson Plumbing Supply, Sprinkler World, Mountain States Supply, or England Plumbing.
I usually use dish soap to lubricate the barbs, but thanks for the warning.
Thank you. Great video
Thanks Bigcal44.
Thanks for the great video
Thanks for the feedback.
We've used that same setup 2 times and both have leaked a few years later, always from where that hose clamp is. Those are meant for soft rubber hoses, not hard, and not supposed to be underground.
same problem here had to dig up my drive way twice to get to the area I needed to fix
Is double Clamps and cross them
Just use a compression adapter, all you do is glue it in to your pvc and slide your poly tube into the compression adapter and done. You can get the compression adapter from irrigation companies on line, they have 1/2", 3/4" etc. The 1/2" compression adapter is only about 20 cents a piece.
Good point.
Hi any idea how I can go from 1/2 cpvc to aquarium air line tubing? I want to install a drip system for my aquarium but can't figure out how to properly tap into the cpvc without leaks
One way is to drill a hole directly into the CPVC pipe and thread the hole to accept your air line tubing valve.
You could also try and find a threaded bushing that would from 1/2" cpvc to 1/4" FIPT (Female Iron Pipe Thread). Then thread a valve with a 1/4" MIPT threads into the bushing that has an outlet for the drip system, similar to the valves in this link: www.drsfostersmith.com/product/prod_display.cfm?pcatid=8165&cmpid=03cseYY&gclid=CjwKEAjw7svABRCi_KPzoPr53QoSJAABSvxfLGxoTL-6W6lR6pDZweDYg00oPOF1Ny1ftV3kou_AhBoCR07w_wcB
Thank you for all of the great sprinkler videos. Is there a good reason to use pvc vs polypipe for yard irrigation? The house we just moved into has polypipe throughout the yard, a lot even above ground. I need to trench and bury everything that’s above ground. Would it be beneficial to convert to pvc while I’m at it?
In Az after 10 years we’ve been getting leaks from cracks in poly hose.
Thanks Looks like I will be doing this today me self :).
Good luck and thanks for watching.
I'm going from pvc to poly and from there to my drippers. Do I need to install a water preasure reducer?
did you need to install a water pressure reducer?
Great video, thank you. This helped greatly. Quick question; what glue/primer do you use? I found some old primer in my garage, but what glue do you use? I am thinking of buying Christy's Red Hot Blue glue, is that OK? The brand of primer in my garage is Christy's.
I use Christy's Red Hot Blue glue.
Thank you so much!!!
How to connect pic to copper tubing
I just use my lighter to slightly heat the poly pipe then the pipe slides straight on but don’t over heat, if it’s too soft it won’t work.
Thank you you are very knowledgeable prime first then glue 👍🏼
Glad it was helpful!
Tell me any adepter for 75mm HDPE TO convert upvc
Anything fastened with a barb and hose clamp is doomed to fail eventually. And by "eventually", I mean at a time of Mr. Murphy's choosing.
Totally agree.
Good video! I am about to transition some lines the same way. Isn't it possible to buy a poly male adapter that transitions in one solid piece to fit the pvc pipe?
I haven't seen one yet.
@@Iscaper yes there is Lowes sells them 3/4 barb to 3/4 threaded male then 3/4 PVC threaded female to glue slip
Is there a way to connect PEX to PVC pipe? i'm trying to run a hot and cold water line in the basement to small bar sink.
+Rodney Morton
You could use a Pex male adapter on the Pex pipe and a PVC female adapter on the PVC pipe, although on the PVC side I would use a coupling and threaded bushing instead of a female adapter. It's too easy to crack or stretch the threads on a PVC female adapter. Be aware that PVC pipe is not rated for hot water, but CPVC is.
What size did you use for the long pvc pipe?
Gavin Venable
PVC pipe is 1", has a 1" coupling glued on the end, with a 1" x 3/4" bushing SXT (slip x thread) glued into the coupling.
Hi, can one join a bigger size PVC pipe of 100mm or above to an hdpe of the same size ? Will it be prudent to join such for a small town water scheme.
I've only seen fittings for HDPE up to 2" (50mm) that would adapt to PVC pipe the same size.
Curious as to why you went from 3/4" poly to 1" PVC then back to 3/4" PVC?
+Daniel Johns
I've never had good luck using PVC male or female adapters. They split and crack too easily. That's why I went with a PVC 1" x 3/4" bushing (Slip x Thread) glued into a 1" coupling, then a 1" x 3/4" bushing (Slip x Slip) glued into the opposite end of the 1" coupling. It makes the transition much stronger.
Hi Kerry my name is John can blue monster pipe dope b used on pvc threads instead of Teflon tape
It should say on the if it's recommended for plastic threaded connections. My favorites are Blue Magic Pipe Joint Compound and Oatey Great White Pipe Joint Compound.
Is there a way to do outside connections to avoid restricting water flow?
If you're transitioning from PVC to Poly pipe make sure the PVC pipe is the same size or a size bigger than the Poly pipe. Also use as few elbows as possible when connecting the pipes.
What part of Utah are you from?
Salt Lake City
Thank you
Welcome!
Cool
@Webkraller
First off..don't use wd-40 if this maybe for a fresh water that feeds into your house.. that's not good.. 2nd use what's called a ford coupling..its compression so all u will need is 2 channel locks and about 3mins of your day....
I believe I've tried to do this, using only a double ended barbed fitting (there was a leak in the poly pipe, so we removed a small section, maybe 3/4"). But I can't get the hose clamps tight enough to keep the repair from leaking. This poly line is buried ~ 2', and services a frost free hydrant, so I'm assuming it has a moderate to high pressure. We need help soon, this is part of lawn sprinkler system, and we need to water soon. :( Thank you!
You may need to cut out a bigger section and use 2 barbed couplings for the repair. Take a 2’ piece of new pipe and push the couplings into each end. Dish soap on the fittings and inside the pipe make this easier. Make sure the pipe pushes onto the almost the center of each coupling. Then I would use 2 hose clamps on each coupling. Instead of a screwdriver try a small ratchet and 5/16” socket to tighten the hose clamps. Careful not to strip out the hose clamps. Next push one end of the 2’ piece of repair pipe with coupling into your pipe in the ground. Remember the soap. Then line up the other end with the end of the pipe in the ground. Make a cut if needed. Slide 2 hose clamp over the pipe in the ground. Put a slight bow in the 2’ piece of pipe to get the last coupling started. Push in and tighten the last 2 pipe clamps. I hope this helps and let me know if it works.
Please explain your tech with putting primer on afterwards. The primer is purple right? Im not a plumber and I don't know if I've been doing it wrong. I always put the primer (purple stuff) on then wait about 20 sec then put glue on both sides then wait 20 sec then twist together. Am I doing it wrong? Somebody Please!
+Phlop Alopagus Never mind I kept watching lol.
+Phlop Alopagus Ok why is your glue more purple then your primer?
+Phlop Alopagus
Waiting on the primer is okay but you want to assemble the glue joints immediately after applying the glue. 20 seconds is too long to wait on some fast set glue types.
+iScaper1 Thank you for the tip I am always looking to do a better job.
+Phlop Alopagus
Thanks and good luck.
Can we get an updated easier way today?
what is the compound you used in the 1st joint gray threaded poly TO white PVC ; ?
Teflon paste.
nice
@samiam6977 can you please elaborate? i am faced with similar situation, 3/4 poly tubing to 1" PVC.
webkraller 8 years later, still waiting on his elaboration 🤦🏻♂️
i would use a normal female socket and then a reducer to whatever size the pvc pipe is.
I don't use female adapters much, they're too easy to stretch or crack the threads when tightening.
the grey fitting is called an insert fitting and
Thanks fpr this/
A compression coupling will work just as well to go from poly to pvc, no need to add primer or cement, just tighten and you're set.
Black poly pipe has a different OD than PVC, that's why you need the barb to male adapter fitting to make the transition. What kind of compression fitting are you referring to?
A compression coupling will fail and leak
@@Iscaper perhaps corporation coupling that’s how they call them here ,graded for underground, not cheap tho.
That type of insert is inexpensive but it chokes down the water flow. If less water flow is not important use them.
Hmmm. Not so sure about that. Are you saying the ID of a plastic insert fitting is less than a metal one? The OD would have to be the same to fit the poly tubing.
The poly pipe can you use pex fittings on it?
+Chad warhold
I don't think a PEX fitting would work on Poly pipe. 3/4" PEX pipe has an OD (outside diameter) of 0.875" and an ID (inside diameter) of 0.681". 3/4" 160psi Poly pipe has and OD of 0.916" and an ID of 0.824". The inside and outside diameters of the pipes would need to be the same for a PEX fitting to work on Poly pipe. I would use a poly insert barb adapter.
No
You like wd40 in your water???
How would you connect Poly to PEX pipe?
Easiest way if you're using 3/4" poly pipe is to use a 3/4" insert male adapter in the poly pipe and connect it to a 3/4" Pex female adapter.
Much too complicated. Use a DIG #207 (1/2") or #5707 (3/4) into a PVC connector, glue the connector to the PVC and insert .700 poly drip. Clean and simple.
Won't WD-40 degrade the rubber?
I was trying to figure out the same thing. Usually the hoses are heated with a gun, very hot water (boiling) or in a pinch just laying it out on the concrete on a hot summers day (10-15min). It's never easy to get them on but it makes a huge difference. WD40 though...
Yep, he should have used heat like everyone else does.
Same type of plastic is used in the automotive industry, fuel tanks, fuel lines. So any spray lubricant isn't harmful to the plastic. And you don't run the risk of melting the line by using a heat source and weakin the plastic.
Or a in line filter???
Yes, most drip circuits operate at 30psi so I would install a pressure reducer with a filter. I like the Rain Bird part# PRF-075-RBY. It is a combination pressure reducer & filter.
I have a poly pipe 1" just like this, and I need connect to a PVC pipe that will be under ground, is that ok use 1 1/2 after? (1" poly pipe to 1 1/2" PVC pipe 40) It works? Will I loose pression?
Thks guys 🙆
Glue a 1-1/2" coupling onto the 1-1/2" PVC pipe then glue a 1-1/2" x 1" bushing SxT (Slip x Thread) into the coupling. Thread a 1" insert male adapter into the bushing. Use teflon paste or thread tape on the male adapter.
@@Iscaper thank you, my concerns is about the sizes. My source is coming in a 1" poly pipe, I don't have a lot of pressure in this poly pipe, so, is okay connect in a 1 1/2" PVC pipe after 1" poly pipe? 1 1/4 should be better? Or I can go with 1" PVC pipe? It's because I never saw videos here with people using 1" PVC , I don't know if it's good.
Thank for your help
@@ellies1877 If your supply line to the sprinklers is 1" poly you would be fine using 1" PVC pipe. I prefer PVC pipe and fittings over poly pipe and fittings in my sprinkler work.
yes it is, and it was developed by the military for use on metal. There is no faster way to destroy synthetic rubber than to spray that stuff on it.
J. Glueck fire would destroy it much much faster
The automotive industry has been using the same plastic for fuel tanks and fuel lines for over 3 decades now, so a little spray lubricant isn't going to harm the plastic water lines.
@@donaldales7739 Fuel lines may be different, but most coolant lines and lots of plastic parts have been replaced in my shop from this kind of damage.
Can a guy get all this from lowes or Home Depot?
Cody Farmer yes
Just buy "P.E. fittings" and your done connecting ppr pipe to pvc/P.E. pipe 😁✌
Instead of the lubricant on the barb, I recommend using a lighter to gently heat the end of the poly pipe so that it slightly softens so the barb enters it easily. Then use a pinch clip, not hose clamp, to secure.
howdy -- why a pinch clip instead of hose clamp? curious. thx.
so poly 3/4 to pvc 1/2 inch? 🤔
In video, 3/4" poly pipe is connected to 3/4" Schedule 40 PVC pipe. If you want to connect 3/4" poly to 1/2" PVC pipe, glue a 3/4" x 1/2" bushing (Slip x Slip) into the 3/4" coupling.
You only need one fitting for this project glue × barb female adapter.
I don't use female or male adapter fittings in PVC because of how easy it is to split the threads.
You should only use Teflon tape on plastic pipes.
No, not a good idea at all. Thread sealant should be used.
I usually DOUBLE CLAMP it
Good tip, thanks for posting.
Wondering why you use primer with blue glue.
With non pressure pipes like drain lines primer isn't required with Christy's. I like to use primer with pressurized pipe and fittings because the primer removes the sheen, cleans, and softens so that there is a good chemical bond after applying the glue.
wow! way to use 4 fittings when you could of done it in one. try a pvc to polly adapter next time. Barb on one end and pvc solvent female on the other
I agree with your reasoning... however his name is unibomber. Therefore he wins.
I would not use WD-40 to lubricate. It will corrode the plastic. Like he said, use dish soap.
Or KY
PoijhvcTheHelvetican
DONT USE ANYTHING. HEAT POLY UP A TINY BIT WITH A TORCH. BARBS WILL SLIDE RIGHT IN. TIGHTEN CLAMP WHILE ITS STILL WARM.
Should be renamed "How to connect Poly pipe to PVC pipe in the most complicated way"
What about poly pipe to a garden hose?
You could use a poly insert 3/4" male adapter for the poly pipe, and attach a 3/4" FIPT x 3/4" MHT adapter to the poly insert male adapter. Attach your garden hose to this adapter.
Here's a link: www.homedepot.com/p/Everbilt-3-4-in-MHT-x-3-4-in-FIP-Brass-Adapter-Fitting-801759/300096107
@@Iscaper the problem is the poly pipe is 1”
@@schoolboy405 Use a 1" poly insert female adapter for the poly pipe. Install a 1" MIPT x 3/4" MHT adapter into the female adapter. Here's a couple of links that might help:
www.amazon.com/dp/B0BHSVJYKQ/ref=sspa_dk_detail_2?pd_rd_i=B0BHSVJYKQ&pd_rd_w=VIBCW&content-id=amzn1.sym.f734d1a2-0bf9-4a26-ad34-2e1b969a5a75&pf_rd_p=f734d1a2-0bf9-4a26-ad34-2e1b969a5a75&pf_rd_r=H5CAYHHJ9GRX9HTA8T1A&pd_rd_wg=jSWOL&pd_rd_r=05870e2d-a7f0-43f0-8066-18f1827d034f&s=hi&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWw&th=1
www.sprinklerwarehouse.com/poly-insert-female-adapter-1-in-x-1-in-fipt-x-insert?gad=1&gclid=CjwKCAjw6p-oBhAYEiwAgg2PgrNDU1pa1Qf0WjMxXytCZKV2ZkCJ8uHU2rmYEuUdUG8rmh0Lx4B58RoCWwgQAvD_BwE
you should be aware that WD-40 is a metal conditioner, and can damage some plastics.
It will leak with that hose clamp
Use double
This is the old way. They make a poly tube adapter that glues into a pvc coupler. Just push the poly into the pvc. Less parts and time
Good information, thanks for posting.
how about tee
You could glue a threaded bushing into the tee.
How about DIP to PVC?
+Alan Fox
I need more info on what you mean by DIP.
Ductile Iron Pipe
+Alan Fox
Most fittings for PVC are IPS (Iron Pipe Size), so if you can get a fitting for the ductile iron in IPS size the connection to PVC should work.
Will this work with domestic pressure water supply?
+Alan Fox
I've done galvanized to PVC transitions with good luck but not ductile iron. The only ductile iron I've worked with was larger size (6") for water mains. The transition fittings are the key. The weak point from a rigid piping like galvanized or ductile iron to PVC is the transition fittings. I don't use male or female adapters in PVC because it's too easy to split or crack them. I like to use threaded bushings with couplings to make the transition fittings stronger. For example, if you have a 1" IPS male adapter fitting on the ductile iron end, I would use a 1-1/4 x 1" PVC threaded bushing with 1-1/4" PVC coupling and a 1-1/4" x 1" PVC slip coupling. Glue the bushings into the 1-1/4" coupling. The threaded end of the bushing would then be threaded onto the ductile iron adapter and the opposite end would accept 1" PVC pipe.
Video is 100 times better sped up 🐢
not the way i would do it!!! only use ALL this stuff if it's all you got...
That metal threaded pipe insert creates a bottle neck in the pipe, essentially reducing it to 1/2." The stainless steal clamp will rust away. The WD-40 can't be good for the plastic materials, spit is better. Have a nice day.
That clamp will rust in a couple years.....
It's stainless steel
Yes p
sure lets use WD40 on the irrigation line i'll be using for my vegetables.
I was thinking elbow grease would work just fine.
flip D I was also worried about the glue being toxic if I was using it for irrigation purposes.
Hopefully wd40 didn't damage the grass
Can't you just put the barb onto the PVC pipe directly instead of all these conversions? Seems really wasteful to do it this way.
You need a threaded IPS fitting to make the transition from insert to PVC. The way you describe would leak and water pressure would blow the insert fitting out of the PVC fitting.
iScaper1 thank you!
Where the FUCK do you find those male to barb fittings?? I mean why THE FUCK is that the holy graile of fittings? I go to Home Depot/Lowes/Ace and ask them for a threaded male pvc to barb fitting and its like I asked them direction to the fountain of youth. PLEASE PLEASE PLEASE give a good source for those fittings. Thank you.
+XCyclonusX
They may not know what you're talking about. You need to ask for Poly Insert Fittings for Poly Pipe. I went to the Home Depot and Lowes websites and typed "Poly Insert Fitting" into their search box and did get results. Home Depot only had a few, but Lowes had a number of the fittings. The Ace website showed no results for poly insert fittings. Here's a link to the Lowes site: www.lowes.com/Search=poly+insert+fitting?storeId=10151&langId=-1&catalogId=10051&N=0&newSearch=true&Ntt=poly+insert+fitting#!
Only problem with that is the ones I found at HD/and Lowes are for threading into metal female adapters. They don't thread into pvc female fittings and they don't have the slip x barb. Thanks though for understanding my frustration. I can always get what I want from Amazon but with a minimum of a 5 day shipping wait I need to get it right the first time, and with shipping its like 10x more than I'd pay from a local store.
+XCyclonusX
The poly insert adapters work on both galvanized and PVC female fittings because the fittings are IPS thread. This 3/4" insert male adapter from Lowes: www.lowes.com/pd_22539-322-350407___?productId=3455128&pl=1&Ntt=poly+insert+fitting will work on a galvanized or PVC female adapter.
Yea home Depot doesn't carry them..try an ace..true value store
@@jayc4715 LOL can't remember why this was so important to me, but I sound a little unhinged. Thanks for the walk down memory lane. :)
You yanks with your imperial fark, not your fault though I understand it’s from the 1%
heat the pipe!!!!!
I was thinking the same thing.. heat the poly pipe up and push.. much easier than hitting it with a hammer
Here is easier form ruclips.net/video/J1ozyeK_AXM/видео.html
Thank you but your video was no help to me
this looks very very unnecessary! 3/4 barbed edge to 1/2 inch female adapter. attached to flex pipe. then attached to 3/4 barbed edge to 1/2 inch male adapter. Oh ya heat the ends of the flex pipe then insert the barbed ends along with the clamps.