Fortunately it seems that my r35s came with the motor but what i wish is to add a mod, a tiny wifi-bluetooth card with a micro toggle switch soldered with wires to the usb-c OTG
@@hackaround there is a way to put some chip to get natively? R36S. without a switch, there is 4 pads on the side of the board... its direct connected to the OTG? or its separated usb port? RX TX VCC GND...
Those pads are for UART. Native is not possible because there is no sdio interface for wifi. You can just forget about org and use it always. Or use the gpio of FN button to control power of wifi
@@hackaround interesting. last question, theres a way to hook up, the switch way, a bluetooth and wifi together on the same usb device? there is a bunch of wifi+bt usb dongle. will work?
Is there any chance of it being possible to install some version of Lineage OS on it? since it runs android. Maybe it would be possible to install some version or a port like 351droid or something like that.
I worked for a while to make 351droid to make it work but is hard without the sources. The problem is the original 351mp had a SPI flash for u-boot, this device does not have it and 351droid uses that u-boot, is not containing his u-boot like the rest of the images. So it will be possible but with a bit of work.
@HenriqueGabriel-gn1tl ok, I have a new android for E6 which is 64bit. Check the channel and you will see the video with the installation of the new android.
Nice vid.
Would you perhaps know wich speaker is used in the R36s, mine is broken and looking for a replacement.
I will measure it. Are you sure is the speaker and not something else? Try to connect any speaker to test
I asked the factory of r36s and they said the model of speaker is 2415
Hi, what rumble motor are you using, I can not find on the internet? Thank you very much Mike
I bought it from here s.click.aliexpress.com/e/_DByis5p
@@hackaround The page is Not Found, they must have sold out
@@hackaround Are they for Nintendo Wii?
Found them, just need to know what voltage 3v or 5v
@@MichaelLoveridge-vg2be 10mm x 2.7mm 3V
Fortunately it seems that my r35s came with the motor but what i wish is to add a mod, a tiny wifi-bluetooth card with a micro toggle switch soldered with wires to the usb-c OTG
For a while they add the rumble motor, then they remove it reduce the cost. To add a wifi mod is on my list for a next video.
@@hackaround there is a way to put some chip to get natively? R36S. without a switch, there is 4 pads on the side of the board... its direct connected to the OTG? or its separated usb port? RX TX VCC GND...
Those pads are for UART. Native is not possible because there is no sdio interface for wifi. You can just forget about org and use it always. Or use the gpio of FN button to control power of wifi
@@hackaround interesting. last question, theres a way to hook up, the switch way, a bluetooth and wifi together on the same usb device? there is a bunch of wifi+bt usb dongle. will work?
On rocknix you have drivers for Bluetooth as well, but not every chip is supported.
What screwdriver did you use?
2mm phillips screwdriver
Is there any chance of it being possible to install some version of Lineage OS on it? since it runs android. Maybe it would be possible to install some version or a port like 351droid or something like that.
I worked for a while to make 351droid to make it work but is hard without the sources. The problem is the original 351mp had a SPI flash for u-boot, this device does not have it and 351droid uses that u-boot, is not containing his u-boot like the rest of the images. So it will be possible but with a bit of work.
@@hackaround Sorry, I forgot to mention that the console in question would be the gamemt e6
@HenriqueGabriel-gn1tl ok, I have a new android for E6 which is 64bit. Check the channel and you will see the video with the installation of the new android.
@@hackaround Serious? I looked and didn't see anything
Sorry, is not yet released. As soon as I finish with E6 Plus I will move back to E6 to add the new android and make new changes to linux CFW
how do you recorded the screen? usb-hdmi hub?
im also wondering, could i hook up the r36s onto my tv, or is he using some screenrecorind featur in retroarch.
No. Using ffmpeg. There is no hdmi output for rk3326
@@hackaround oh ok software based, inside retroarch.
@oToddy.mp4 it needs to be compiled separately and it will record the full screen, not just retroarch.