P0 to P5 Escooter LCD Settings / P Setting - Guide - Part 1 of 2
HTML-код
- Опубликовано: 6 окт 2024
- In this tutorial, you will learn how to configure the (P0 - P5) P / LCD settings of your e-scooter.
To configure the settings, press ‘Power’ + ‘Mode’ buttons at the same time this will direct you to the P / LCD settings as follows:
1. P0 (Wheel diameter in inches: 8, 10, 11, or otherwise; My setting: 10) - Press either ‘Mode’ button to increase the value or ‘P’ button to decrease
2. P1 (Low voltage protection cut off; My setting: 43V) - When the scooter reaches the specified value, say 43 volts, it will shut down or get cut off. This feature helps protect your battery. Press above mentioned buttons to increase or decrease value.
3. P2 (Units: 0-Kph or 1-Mph; My setting: 0) - Ditto to adjust value
4. P3 (0-Immediate Start or 1-Kick Start; My setting: 0) - Difference is:
(0) Immediate start - When you pull the throttle the scooter starts moving immediately from standstill position,
(1) Kick start - from the word itself you have to pull the throttle and manual kick first, scooter moves forward from standstill position, then scooter runs. Ditto to adjust value
5. P4 (0-Off/Non-continuous or 1-On/Continuous/Cruise mode; My setting: 1) - To activate cruise mode make sure P4 is set to 1 and pull the throttle for 6 to 8 seconds. Ditto to adjust value
6. P5 (0-Hard acceleration or 1-Soft acceleration; My setting: 1) - Hard setting is immediate acceleration when you pull the throttle, Soft is otherwise. Ditto to adjust value
My setting is abovementioned, however, you can of course adjust the settings of your e-scooter based on your personal preference.
Please do not forget to click LIKE and SUBSCRIBE to my Channel.
#Electricscooter #Escooter #Autech #XThunderDual #XTrack #Dubai #UAE #LCDsetting #Psetting #P0-P5
Very helpful video best one i have seen yet, thank you.
Thanks for it
Hi sir cannot access P settings e10 1000 watts Rohan wings brand najx t controller
I cannot access the p settings . And only displays the voltage and Odometer only , please help someone
What is you scooter
Same
@@ronaldmariano3224 akez 1000w electric scooter
How do you unlock speed on this controller?
Ye i wana know it too please someone lemme know.
@@krutaisLV worked on mine :
Turn power on while holding your brake lever in. ( keep holding it till I tell to let loose). Pull the accelerate lever all the way in and let loose. Now pull the acceleration lever in a second time but hold it for 10 seconds. After those 10 second release the acceleration lever and brake lever. Turn off the scooter. And turn it back on.
This unlocked mine to 35 km/h in mode 3
@@rubenVS100 ok how to you make it slower
@@rubenVS100 I want the top speed to be 37 kmh
E10 ko sir d ako maka punta sa p settings sabay ko namnn press yung power and m buttons ng off siya.
ยี่ห้ออะไรหลอคะ
even me i cannot open the p setting my scooter is x thunder 4000w dual motor
Are you now got the p-settings please I want because I want to set a speed limit to 37 cuz it’s very fast
How to change voltage to 48 and not 54
If you are in Dubai...look up Repair and Fix on Facebook...he might be able to help
@@ronaldmariano3224 I'm in uk but thank u
48 volt cell gets charged by 52-56volts as seen on the back of your charger so displayed its saying 56 volts the sign of a good battery, the change volts is motor controller cut off he sets it to 43 this is to stop the battery being drained to a voltage it wont recharge, the voltage displayed is by this factor...