Jetta TDI 2.0l EGR how it works where the valves are P401 P2002 P0401 codes

Поделиться
HTML-код
  • Опубликовано: 26 янв 2025

Комментарии • 59

  • @mauricerohrer
    @mauricerohrer Месяц назад

    Awesome thanks! Fixed a 2013 with the P0401 by cleaning out that filter screen.

  • @quarterpanel
    @quarterpanel 2 года назад +3

    I have been getting P401 and P2002 and have sent it to VW service for the fourth time in as many months. This TDI is under warranty. They have replaced two DPF's and one EGR Cooler. The same codes just came back after 200 miles. Its back at the dealer again!

    • @dickdangles3453
      @dickdangles3453 2 года назад +1

      Hey I’m having the same issues. 13 Jetta tdi. I replaced the pipe from dpf filter to egr cooler and that worked for a couple of weeks. I finally bought some dpf cleaner and pulled an o2 sensor on top of the dpf filter and filled it full and then drove in 5th gear for 12 miles when it did a regen and so far no check engine light for the last 370 miles. The car has 207K on it. Just curious what have you found out.

    • @tangoseal1
      @tangoseal1 2 года назад

      Stop uising additives in your fuel and use just pump diesel and NOTHING else.

    • @Mikefngarage
      @Mikefngarage Год назад

      ruclips.net/video/Er2gyoaBH2M/видео.html

  • @mikesrandomvideos
    @mikesrandomvideos  2 года назад +4

    I fixed mine with only doing a regen and then after the regen adapting g450. G450 should only be adapted after doing a regen. Either regen while driving or Regen while standing. Done through VCDS.....under Basic settings. you also need to do a security access before and make sure the codes are reset. REset codes turn engine off then back on go to security access (16) then put the code in press do it. then go to basic settings do the regen while standing. follow the prompts brakes then floor throttle. Regen will start. After that turn key off then back on and do the G450 procedure. to adapt g450.

  • @tltgarageusa7474
    @tltgarageusa7474 2 года назад +6

    I just replaced a 2012 engine and had dpf code and Nox sensor code. I know it had a newer dpf so I knew it was good. After doing some research I take it out on the freeway put it in manual mode and drove it at 2500 rpms in 5th gear for about 20 minutes. That took care of it. Hope that helps someone else. I believe it is a forced regin.

    • @Mikefngarage
      @Mikefngarage Год назад

      ruclips.net/video/Er2gyoaBH2M/видео.html this video is how to clean your particulate filter then do a regen. Fixed mine permanently. seems to work great now over 3000 miles.

    • @jeffsmith-ze6wb
      @jeffsmith-ze6wb 3 месяца назад

      THANKS so much for the info I appreciate it!!

  • @titorojas333
    @titorojas333 5 месяцев назад

    Question for the DPF I have seen on RUclips some folk use DPF flush cleaner. I actually bought that on Amazon plug of the hole and O2 sensor remove, than pour that flush liquid backwards and place upside down and let sit for over 24 hours. I was amazed how filthy the Particular filter was and how much black particle come out!!!! I end up going to the car wash and pressure wash it in backwards direction until I got nothing but clean water. I’m in the process to putting back and see if that removes my P1A58!

  • @davidsmithers3353
    @davidsmithers3353 27 дней назад

    The first pipe flex pipe that’s the egr bypass no?

  • @mikesrandomvideos
    @mikesrandomvideos  2 года назад +2

    THanks for watching and thanks for your comments.

  • @Charlie-en1kr
    @Charlie-en1kr 2 месяца назад +1

    Did i just throw p2002 and p401 because i didn't adapt g450 after installing new ones? Any one know the process ? What settings on vcds?

  • @volvoripr9980
    @volvoripr9980 2 года назад +1

    hey man hope you can respond this .. I am getting a P0486 and wont go away 2012 tdi passat same system as yours

  • @guaporubio
    @guaporubio 4 месяца назад +1

    My question is how do you clean the rear EGR and filter without taking apart half of the car? The videos on RUclips are using products that seem to only be available on other continents. Mostly Europe and Australia.

    • @mikesrandomvideos
      @mikesrandomvideos  4 месяца назад +1

      Most of the problems are in the egr I forget what it is called. it is a tube between the exhaust and the Rear egr. I think it is EGR filter. Take that off and if you cant blow through it with no resistance it needs to be cleaned or replaced. Clean with degreaser water and or oven cleaner from walmart.

  • @farmgirlpicker6423
    @farmgirlpicker6423 7 месяцев назад

    I have a 2006 TDI Diesel Jetta with a code of P0404 - EGR - a control circuit range performance. It starts and black smoke comes out and then stalls immediately. Happened very suddenly. I am having trouble finding a diagram or video with the location of the EGR valve. Any help would be appreciated. ! Thanks!

  • @aaron___6014
    @aaron___6014 2 года назад +1

    Is this a cjaa engine? My Jetta has a different looking lp-egr filter.

  • @adrianvaldez8831
    @adrianvaldez8831 Год назад +1

    I’m able to use the older egr filter on a Tdi with the newer

  • @yandybatista5618
    @yandybatista5618 2 года назад +1

    friend I have a jetta 2013 diesel and the check light came on I turned on the P2002- P0401- P240F the car has 94800 miles that you recommend I am here in Florida United States

    • @lard1892
      @lard1892 Год назад +2

      Warranty..Go to Dealer

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад +1

      TRUE go to the dealer ASAP. I believe your emissions warranty covers that under 100k miles. you should be good.

  • @ronin6158
    @ronin6158 2 года назад +1

    The TDI has two EGR's correct? On the front of the intake and this one in rear?
    This code are for the rear correct? (I cleaned the front one so I think they must be)
    001025 - EGR System
    P0401 - 001 - Insufficient Flow - Intermittent

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад

      most problems are on the rear. and that filter. or the intake getting plugged up. Or the cooler getting full of carbon.

  • @Perkulate420
    @Perkulate420 Год назад +1

    Lets say, hypothetically, you have acquired a car that had the dpf and egr delete kit from rawtek installed already with the stage 2 malone tune.. then this code p0401 pops up.. tuner says the code has been tuned out but it still shows up.. car feels sluggish..any idea why this is happening?

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад

      Tune must not have included EGR delete. May need to have tuned forced Readiness. Check Stevenson tuning. They are in Europe. so they can tune anything out. Hypothetically assuming its for racing.

  • @ThatOneLateGuy
    @ThatOneLateGuy 2 года назад +2

    Ive just had warranty work that replaced the dpf, the egr cooler, and the egr filter. couple hundred miles later and now out of warranty, the p0401 code came back. Any suggestions on what I should check first?

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад +1

      usually it is one of the items that was replaced. Try doing regen while standing. Using ross tech. may clear code. Clear code. do regen while standing and drive it for a while. If not check EGR filter. usually that first.

    • @lard1892
      @lard1892 Год назад +1

      Warranty lasts 4yr/54k mi after dealer repair...take it back

  • @longhuynh5249
    @longhuynh5249 Год назад +1

    Good info, thanks

  • @aggressivedog3742
    @aggressivedog3742 Год назад +1

    I cleaned my vw 2009 jetta tdi egr valve and I am still getting a P0401 code, what would you recommend?

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад +1

      Did you clean the EGR filter. it connects between the exhaust tube and the lower egr valve....remember there are 2 egrs. upper and lower. lower egr tube is usually the problem. but you could have a restricted DPF.....do a regen while standing. Lots of testing to do. If you remove it you should be able to blow through it with no resistance. Cleans up with oven cleaner walmart yellow can. If you have a CBEA......DID you replace the Oil pump???? critical engine fail on that year only.

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад +1

      I finally cleaned my DPF and now I have no more codes. Made a video on my other channel. ruclips.net/video/Er2gyoaBH2M/видео.html

  • @henrynicholson1779
    @henrynicholson1779 2 года назад +1

    Hey man.. garage says my egr cooler has corroded and leaking.. they want to charge me for full genuine egr and cooler, I’ve found just the cooler second hand nice and cheap which I’ve picked up. I take it from your video that it’s perfectly readable to just change over the cooler, keeping old egr? Would I need any new gaskets to go with it? Hopefully you know so I can pick some up before I turn up to the garage with a random cooler, when all they want to do it swap old for new. Cheers!

  • @mitchellblow5179
    @mitchellblow5179 2 года назад +1

    Hi would this make the car shudder or jerk in lower revs under load?

  • @drewdejesus1385
    @drewdejesus1385 Год назад +1

    What year and vehicle specifically did this egr/ engine come from? What year range would this system be in?

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад +2

      09 till about 14. then they changed it a bit. But still similar

    • @drewdejesus1385
      @drewdejesus1385 Год назад +1

      @@mikesrandomvideos thanks for the reply, ik this video is quite old

  • @Michael_Blankenship
    @Michael_Blankenship Год назад

    What year model is that engine?

  • @vincentzuhowsky3076
    @vincentzuhowsky3076 2 года назад +1

    what year vehicle is this? does this apply to a 2012 audi a3 tdi ?

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад

      yes I have an 11 a3 it is the same. Has CBEA engine and they are exactly the same except for the oil pump and balance shaft

  • @jawadloulou3567
    @jawadloulou3567 2 года назад +1

    hello everyone I really have a problem with this error code golf sportsvan 2015 the error code p2002 I did everything on this vehicle my error code appears all the time? what are the tracks to follow to restart please

  • @susankadar4626
    @susankadar4626 Год назад

    Do you know a tdi mechanic in the so cal area or do you work on tdi’s?

  • @NikkFlo
    @NikkFlo 2 года назад +3

    Just got both those codes yesterday 😔 … thank you for the info and detail. Hopefully I can tackle this myself. What’s your stance on deleting? I dont have smog in my area. for the price to fix this if it is the dpf/egr issue , delete is cheaper. I have it going into the shop next week for timing belt replacement so this kind of came at a unfortunate time lol

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад +1

      might be OK....check EGR filter goes between the Exhaust and the Rear EGR. Then do a regen while standing. Might take care of it. should be able to blow through it pretty easily. usually it is pretty fixable. if it cost more than delete then maybe go that direction.

    • @yandybatista5618
      @yandybatista5618 2 года назад +1

      friend I have a jetta 2013 diesel and the check light came on I turned on the P2002- P0401- P240F the car has 94800 miles that you recommend I am here in Florida United States

    • @lard1892
      @lard1892 Год назад +2

      @@yandybatista5618 Warranty...go to dealer!!!

    • @DJgoon12
      @DJgoon12 Год назад

      @@lard1892 it's under warranty until like 150K miles I believe.

    • @mikesrandomvideos
      @mikesrandomvideos  Год назад +1

      @@yandybatista5618 emissions warranty is extended because of dieselgate

  • @michaellyons8236
    @michaellyons8236 2 года назад +1

    What's your thoughts on a solution to a p0403 code I just replaced the egr valve and cooler and I'm still getting that code also I'm getting a p046c

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад

      Check wires between. Test with VCDS for actual movement of the valves. Use VCDS to do a EGR test it will open and close the valves while standing. engine not running verify they are working. Look at the wiring harness near the fans make sure it is not worn through. Probably harness or connector loose or not getting continuity. Also do a Differential pressure Adaption and reset them. All done through VCDS.

  • @lonewolf031
    @lonewolf031 2 года назад +5

    I'm getting code p2001 and p0401.

  • @jeffsmith-ze6wb
    @jeffsmith-ze6wb 3 месяца назад

    I’m guessing,wondering,suggesting oven cleaner to clean it?? Just an idea.THANKS

  • @Mikefngarage
    @Mikefngarage 2 года назад +2

    nothing like getting someting fixed

  • @Trump-sd2ds
    @Trump-sd2ds 2 года назад +1

    Can I just delete this crap?

    • @mikesrandomvideos
      @mikesrandomvideos  2 года назад +2

      its illegal but if your "racing" ha ha you can. But I will tell you it is not cheap to do so. they make pipes for removing the front egr and a straight pipe for the exhaust. then you need to get a delete tune. Stevenson tuning does them with forced readiness. So if for instance hypothetically someone wanted to keep their EGR valves on there and wallow out their particulate filter and Catalytic converter. they would look like they are working but no engine light and if someone serviced it at the dealer there would be no trace that it was deleted. That is called Forced Readiness. its over 1000 for the tune alone. in all honesty it is easier to fix it. Put a post on the TDI club forum someone will help you.