I have a question, friend, when using the steering wheel, did you use a higher voltage like 13 or 14 to use it? I used the 12v directly and the power source blew up.
I'm currently using a 12v power supply. I have measured the voltage it's 12.56v. and it supports up to 24 volts. that's not your voltage problem. maybe it is a power supply ampere problem or your power supply fault.
hi bro, i wired everything just like you but the motor doesn't rotate, i can feel some resistance but when i rotate the encoder the motor does absolutely nothing, i wired it on the bts controller and on pins 10 and 11 but nothing
So far it’s been okay, but mine when rotate right until limit, either the arduino or the motor will make high pitch noises and signals are going crazy. I will try adding the resistor soon. Is there any other possibilities that causing this?
Yes I Wonder too but i think emc lite is just too Limited and Efe Wheel is free with Desktop Effects ffb Setting etc. Although i dont think there is a huge difference between the Desktop effects but its clear that emc pro is better than Efe it dosent give any errors but it costs 10$ and on the lite Version the degree is only Limited to 900 degrees so of you want good experience better go with emc pro
bro, I made it using the Canon IP2770 encoder and and it can be used, but after I remove it and put it back on, why doesn't it work? even though all the connections are correct, they are still unreadable. Is the ppr wrong? or another possibility?
check your z toogle switch is on position. and reset the wheel config settings and see its work. And if there is a problem with the wheel, the Device status doesn't show ''ready'' (in wheel config)
@@zudumalli I got my leonardo, when I press Reset button, it shows as arduino uno bootloader for a second then it just reverts back to Arduino leonardo. If i try uploading firmware using Xloader, it shows upload failed
bro help me i have problem that the arduino get recognixed and it works afterfew minutes the rx and tx just : rx: blinks nad after tx blinks and one minutes later same its boot cycyling? sorry for my bad english
*Fixed all issues in wheel configuration* - ruclips.net/video/U0nuY5OHgUA/видео.htmlsi=NAqeNzsIOhJLtEcB
If you making this, here are some tips you should know. Be sure to watch. ruclips.net/video/7EY1GpAGPck/видео.htmlsi=PEOsDiciiBHmt72X
hi man, when will the pedal shifter and f1 wheel video release? please tell me the date because I am making it for a competition 😄
The paddle shifters are still not finished. Some parts have not been found yet.😐
I have a question, friend, when using the steering wheel, did you use a higher voltage like 13 or 14 to use it? I used the 12v directly and the power source blew up.
I'm currently using a 12v power supply. I have measured the voltage it's 12.56v. and it supports up to 24 volts.
that's not your voltage problem. maybe it is a power supply ampere problem or your power supply fault.
Nice bro ❤
Thanks 🔥
Bro can i use 12v 10a smps power supply for 775 dc motor
hi bro, i wired everything just like you but the motor doesn't rotate, i can feel some resistance but when i rotate the encoder the motor does absolutely nothing, i wired it on the bts controller and on pins 10 and 11 but nothing
increase all the game effects on RFR wheel config. and restart to apply the settings.
GIMX Adapter for your ffb wheel
So far it’s been okay, but mine when rotate right until limit, either the arduino or the motor will make high pitch noises and signals are going crazy. I will try adding the resistor soon. Is there any other possibilities that causing this?
try flip the motor cables
Why didn't you use the EMC Utility Software?
What is the difference between EMC Utility and RFR Wheel Config?
Yes I Wonder too but i think emc lite is just too Limited and Efe Wheel is free with Desktop Effects ffb Setting etc. Although i dont think there is a huge difference between the Desktop effects but its clear that emc pro is better than Efe it dosent give any errors but it costs 10$ and on the lite Version the degree is only Limited to 900 degrees so of you want good experience better go with emc pro
And also arduino isnt Supporten anymore since 2019 for emc pro so your forced to buy a stm32 for the new updates
Balan hitiye.bro .thanks ❤️
😊
bro, I made it using the Canon IP2770 encoder and and it can be used, but after I remove it and put it back on, why doesn't it work? even though all the connections are correct, they are still unreadable. Is the ppr wrong? or another possibility?
check your z toogle switch is on position.
and reset the wheel config settings and see its work.
And if there is a problem with the wheel, the Device status doesn't show ''ready'' (in wheel config)
bro can u put a 5 minutes gameplay video on this setup❤❤ 🔥🔥
I will soon
ok bro thx😍😍@@zudumalli 🔥🔥❤❤
waiting❤❤🤘🤘@@zudumalli
Bro I only want to use the software for pedals and H shifter, can this software be used? I will be using Leonardo only for this. No steering wheel
yes you can
@@zudumalli I got my leonardo, when I press Reset button, it shows as arduino uno bootloader for a second then it just reverts back to Arduino leonardo. If i try uploading firmware using Xloader, it shows upload failed
Hi 😊😊 I setting all succesfully. But steer wheel not rotate.
Did you install the two resistors related to the encoder?
Nice bro. Did you find a solution to the DC motor overheating?
Now there is no overheating. I think it's a problem with my previous motor.
Bro can we use Logitech
shifter and this steering wheel together
yes
Bro can you make one for me
bro help me i have problem that the arduino get recognixed and it works afterfew minutes the rx and tx just : rx: blinks nad after tx blinks and one minutes later same its boot cycyling? sorry for my bad english
Can you send a video of what happened? To my facebook page
Bro which games can we play using it
9:42
Steering wheel ekt 5A power supply ekk use krt awlk nadda
Motor eka mokakda
Bro i have an problem at xloader upload was failed
Software is not able to download
Bro can i use motor encorder instead of this encorder you used??
Yes, watch my last video I explained this
@@zudumalli Thank you bro for that amazing video❤️
hello, it can work with arduino uno?
no
bro when you will upload next video
In two or three days. If you have any problem send me a message on my Facebook page
Why should we install arduino ide
Some important drivers are required to run Arduino programs.
❤️😍🔥
❤
This works with PS4?
No sir
mine after uploading the frimware it rotate and never stop
make sure the wheel config command mode is ( PWM +/- ) or reset all settings to default
hello bro
can you make a tutorial for Inverted pedals like in the video
Yes, soon
Bro can i edit the hex file?
i think no
❤❤❤❤
BRO CAN WE PLAY NFS GAMES
I haven't try