Helpful Woodworking Tricks You'll Actually Use | Useful Woodshop Hacks
HTML-код
- Опубликовано: 19 май 2024
- In this video i share some Helpful Woodworking Tricks You'll Actually Use, Useful Woodshop Hacks. Head to www.squarespace.com/bourbonmo... to save 10% off your first purchase of a website or domain.
Merchandise & Plans: www.bourbonmoth.com
Patreon Page: / bourbonmothwoodworking
Cameo: www.cameo.com/bourbonmoth
Instagram: / bourbonmoth
Links below to tools and supplies:
3M Cubitron Sandpaper: lddy.no/1hset
Board Feet Easy App: appgrooves.com/ios/416379041
Rockler Universal Fence Clamps: www.rockler.com/universal-fen...
Woodpeckers Clamping Squares: amzn.to/2W63hV8
CA Glue: amzn.to/3AecSIu
Butane Torch: amzn.to/3xliKxG
Digital Micrometers: amzn.to/3CmWLtN
Eye Protection: amzn.to/3gIO4A5
Woodpeckers square: amzn.to/3q8XObc
Drill & Driver https: amzn.to/35zBfmz
ISOtunes Bluetooth Hearing Protection (10% off code- BOURBONMOTH10) bit.ly/BourbonMoth10
Bits & Bits Precision Cutting Tools (10% off code- BOURBONBITS)
bitsbits.com/ref/6220/
RZ Mask (15% off code: BOURBONMOTH15)
www.awin1.com/cread.php?awinmi...
Total Boat Epoxy: (10% coupon code TOTALMOTH) www.totalboat.com
Nicks Handmade Boots: bit.ly/3vZ8uMR
Firm Grip Work Gloves: thd.co/3LEO5TE
PowerPro Fasteners: amzn.to/3u3Mgtj
Pony Jorgensen Clamps: bit.ly/3knr9fZ
Spec Ops Hammer: amzn.to/3fMjAOd
Spec Ops Tape Measure: amzn.to/3w1M788
Spec Ops Pry Bar: amzn.to/2Ro3iC2
Spec Ops Chisels: amzn.to/3ga8kKv
Spec Ops Screw Drivers: amzn.to/3ciV8ls
Spec ops utility Knife: amzn.to/3g5ysWZ
Grizzly Tools:
Table Saw: amzn.to/3q8Wbu6
Jointer: amzn.to/3gFHE6a
Planer: amzn.to/3xCzH7r
Dust Collector: amzn.to/35AFEWw
Air Filtration: amzn.to/3zyXXsK
Band Saw: amzn.to/3gEtCAm
Drill Press: amzn.to/3xvhxEh
Lathe: amzn.to/3vChWUb 
Хобби
![Minecraft but Players Can Upgrade [FULL MOVIE]](http://i.ytimg.com/vi/QRRgLJs4ZPk/mqdefault.jpg)
![Natanael Cano - Ya Te Olvidé [Official Video]](http://i.ytimg.com/vi/xLig8I91SJQ/mqdefault.jpg)
The author does like to from scratch, ruclips.net/user/postUgkxbnOKZBE4evMO5V2vroHeCjq6d_MV6wJO shaping and trimming wood from large blocks into fine finished products. As another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us don’t have the room or budget for. But, knowing how to do these things, even if we won’t be able to practise the full stack project, is still great.
The BF app is the single best advice you’ve ever offered!!! I hate calculating board feet!
"it's just what woodworkers call 'superglue' to make other people feel inferior"
BRING THAT HEAT!
We chemists call it cyanoacrylate to make woodworkers feel inferior. 😁
@@RatBasterd ha!
@@RatBasterd nosebleed😁
Holy hell those falls were Hollywood stuntman worthy, the last one was thunderous.
Thanks for the useful tips! I’ve been woodworking for more than 65 years; yeah I’m kinda old, and I always pick up something new from other woodworkers. Thanks again, you present concepts in a very understandable way.
In October of 2017, I cut my left index finger by trying to cut a tiny piece of cherry shoe base moulding at a 45 degree mitre angle without using the zero clearance fence (plus I had taken my blade guard off of my mitre saw). Needless to say, I was rushing and didn't allow the blade to get up to full speed before making my cut with my left index finger holding the piece of shoe base against the saw fence within an inch of the saw blade and when the teeth made contact with the wood it caught and kicked the piece of wood, pulling it (along with my left hand/index finger) into the rotating blade. Chewed up my finger pretty bad. Happened so fast. I immediately grabbed my finger and squeezed it firmly with my right hand and could feel bone protruding and I knew I had just nearly chopped it off. I was working on a jobsite at a customer's house and didn't have my guys working that day (I'm a self employed finish carpentry contractor who specializes in interior trim work/moulding) so it was just me and the homeowner/customer there. I knew I needed to go to the hospital immediately but couldn't drive myself cause I couldn't release the pressure I was exerting with my right hand. So I went into the house and told the homeowner that I needed her to take me to the hospital. She dropped me off at the emergency room and left and when I showed my finger (or what was left of it) to the ER paramedic, he said, "Oh wow, ok you can continue to apply pressure to it (squeeze it). I'm not going to lie. It's bad. It's really bad. One of the worst injuries I've seen and I've seen everything."
I said, "That's what I was trying to tell you!"
So, to make a short story long, what had happened was the saw teeth had ripped and shredded along the side of my index finger, causing multiple bone fractures and the severing of a lot of nerves and tendons as well as chunking out the muscle and tissue right along the side of my finger from the first/top/end joint (distal interphalangeal) to the tip of my index finger (so about an inch or so of my finger or about 25% of the overall length of my finger). After hours of waiting for something to help the pain, they finally numbed it with something similar to what dentists use to numb your gums (i.e. Novacaine or Lytocaine). Then I overheard the nurse and X-Ray technician discussing the situation and that it was definitely going to have to be amputated. I wasn't shocked when I heard that but it was still hard to hear, even though I had already realized my left index finger was pretty much toast. I tried to take solace in the fact that I'm right handed and pretty much do everything with my right hand because the left has always been basically retarded, weak, and uncoordinated so I was momentarily consoled that it was not my right index finger. The consolation, however, was short lived when a haunting thought came to my mind; that one of my favorite hobbies was playing the guitar and, being a righty, I strum with my right hand and my left hand does the fingering along the fretboard (pressing down the strings). That's when it really hit me how significant it was going to be to lose my left index finger, in part or whole. And it wasn't just thinking about not being able to play the guitar again without great difficulty (or at least not well) and thinking about other things that would be more difficult if not impossible to do (like rock climbing which I enjoyed although I wasn't a climbing fanatic like friends of mine are), but I was also contemplating, with dread, the aesthetic implications; by the sheer grotesqueness of becoming an amputee; a gimp, forever (I was very superficial and vain when this happened). I thought they were going to have to amputate at least half of my finger. But it turns out they were able to salvage everything below the first finger joint (the distal interphalangeal). So I ended up losing about an inch of my finger. Totally sucked and it took me about a year to be able to play the guitar without the pain being overbearing, but now I can pretty much play at the same skill level (or lack thereof) that I was at before the accident. The moral of the story is to be safe when using power tools and learn how to do things the right way, safely before taking risks that could change your life forever. It tends to happen so fast, in a split second, and your life is forever changed. And there are so many far worse/more serious stories of accidents involving power tools than my story. I consider my story to be quite mild by comparison and really ended up being something that made me reconsider my shallow, materialistic, vain, and Godless existence which ultimately led me to Christ which is worth infinitely more than losing part of my finger so I now consider it a blessing. God bless.
I consider myself an experienced woodworker. I find myself learning all kinds of new techniques and ideas from the maker community. The miter saw fence will be made today. Thank you Jason.
I have saved a bunch of money and cut my time in half because of your tips and tricks videos, 🖖👍🤝
As a budding woodworker, I really appreciate these videos for giving me the tips needed to keep at least some of my fingers attached. Thanks, Jason!
As a long time carpenter / woodworker, I had to subscribe. You exhibit two of my favourite qualities. Highly informative, extremely entertaining. Thanks man. Love your video.
OMG I've been confused about what cathedrals are meant to tell me about grain direction for so long! Thank you!
I’m a lady who used to do a lot of woodwork as a child back in my old country, but I’m really in love with your joyful spirit and smart u are. I want to start my woodwork to do my things myself. 😻😻😻
I like how you get right to the subject . Thanks for respecting my time. Most other channels just like to hear themselves talk and talk and talk . Thanks. Love your format. Simple and good info. I think your humor is great.
Jason, thanks for the miter saw jig. Very helpful. Keep them coming.
This is fantastic. You are an amazing teacher!
I have had a pair of those fence clamps for years, and yes, they are fantastic!
Woodworking fun on a Friday night. Thank you for the CA glue tips and the miter saw jig tip. Have a great weekend sir.
Good mornting, after being diagnosed with Parkinson. I find that watching your videos helps relieve the symptoms of the disease. Keep it up!
Even though I do learn a lot, my favorite part of your videos is the sillinesses. Thanks for keeping it fun and educational!
I've just now started doing some very beginning woodworking things in my garage. I just had to take a minute to let you know I really really enjoy watching your videos and I've learned so much already and I can't wait to learn more as you keep posting videos. Thank you for all your effort in the videos you post, quality of content, etc. 10/10 sir!
That’s really great. Can I make a suggestion (from an old man with 45 plus years of woodworking). There is a normal emotion of, when just starting, wanting to make things. And make things. And make things. Don’t fight that but try to balance making with learning. By which I mean learn and practice the basics - without which anyone would be a hack and not a craftsman.
First for me would be measuring and marking. Firstly then, you need accurate and reliable rules, tapes and squares. That doesn’t mean the most expensive (most people like owning lovely things; people drove a Rolls Royce but it doesn’t get you there any quicker than a Mini). It doesn’t have to be new. It often doesn’t matter that your tape is 1mm inaccurate over 2m as you probably want reliability more than absolute accuracy. For example, you measure an alcove with your tape at 997mm - when actually it’s 998. But, when you cut a piece to fit nicely, you use the same tape to cut at 997mm and it fits. The square needs to be square; easy test; take a scrap of sheet paper or card or even mdf. Place your square on it with the short edge of the square facing left (needs to be accurately placed at the edge and sometimes a thicker piece of card or timer makes this easier) and the long side on the card/timber. Draw a line along the long side with a sharp pencil. Then flip the square over with the short part again along the edge of the card but now facing right. The long side should be very near to where you had it before. Draw another sharp line. If your square is perfect, then the 2 lines that you have drawn will be parallel. If they are not exactly parallel, then you can measure the degree by measuring the out-of-parallel and dividing that by 2. For example, if your out of parallel measurement is 2mm, then your square is out of square by 1mm over the length of the long side. If your square has been bought new, then don’t touch it, just take it back. If it’s secondhand, you can certainly try and make it square by taking a sheet of emery paper wrapped around a long piece of timber and try to rectify the inaccuracy. Personally, I would just throw it and learn the lesson.
Then you have the good ways to mark; to saw; to chisel. Actually, there are lots of good ways and a few bad ways. There is no ONE way. If anyone finds this useful, I’m happy to write a bot more.
I'm a hobbyist woodworker, that has no legs. I can't afford to lose anymore limbs. That miter sled/jig is brilliant. Thank you for taking the time to share you very helpful tips.
That splinter removal tip got me laughing 😆 Definitely learned something new!
So helpful Jason. Thank you so much for these tricks. Can't wait for the next one. I'm sharing with my friends right now.
This is a very cool sled with a "gripper" piece of sandpaper! Brillant !
Love your channel, catch myself watching it all the time. Great dry humor and very helpful content!
Fantastic dude, love your candid humour, keeps me coming back!
Can't help but notice you're an elk hunter. Just became a bigger fan.
Thanks for all the "trips and tips" in this video!
Thank you for posting this vid. Like the Rockler Universal Fence Clamps - going to be ordering those!
Great tips. Love the small parts hold down. I will need to add that mine. Thanks
I like the caliper tweezer idea, next time I will try to remember this tip. Thank you.
One of the best tips video yet! Very helpful. Thanks
Thanks, for the reclaimed wood tip. The last tip was great too.
Regarding the qtip trick, I do the same thing with chop sticks. Really handy for stripped out door hinge screw holes.
Golf tee’s are another good one for slightly larger holes
Tooth picks are another option.
I keep a box of wood matches in the van for the same
in a tight spot i once shoved gorilla glue covered pieces of cardboard into rotten door jamb screw holes bc the glue expands - it worked great too !
I use 10 inch bamboo skewers. Something like 100 in a pack for a couple bucks at the discount store.
And what you don't use in the shop can be used for cooking! Lol
i am glad i found your channel i have learned so much
Great tips and I love your presentation. Now I'll work through your back catalogue. Thanks 👍
Your tips and tricks videos are some of your best. Keep them coming.
Thank you Jason you are a mind of information and a really good joiner. Take care with all those stunts🤗
Great tips, thanks a lot Jason !!! The "mitter sled" will be built as soon as possible !
Edit : Some times later… done ! And can't wait to use it !!!
The match stick trick was new for me, thank you!
I wish I had as much energy you have even half of it I would be happy with
Wood golf tees work great for filling holes as well.
Another great video Jason. You used a Q tip to fill a hole. Bamboo skewers work really well also.
Those "micrometers" look suspiciously like calipers. Very useful video. Thanks.
I've never thought about using wooden Q tips to fill a hole. My dad taught me to use toothpicks. I love your videos and have learned many things. Keep of the great work good sir!
For larger holes, I've used a wooden golf tee....good tip
Skewers, garden stakes...
Dude, you are hilarious! I wish you were my next-door neighbor!
Thanks for all the tips and tricks!
I love this channel....keeps me laughing and learning at the same time
He who dies with the most clamps wins
I'm pretty sure I'm losing. I better order some more...
Keep Being You
He who controls the clamps, controls the universe.
He who dies with the most clamps held it together for a long time.
I thought it was old car tires
That final leap from the sky was incredible brother! Thanks for the amazing tips. Now I know how to attack splinters. 🧐
Thanks! Great content. Love the entertainment, with really good information no less. :). Gotta run and make me a 0clearance fence for my mitre saw. Great idea with the little piece clamp! :)
Thank you so much for the cool tips . I am a newbie and really love the way you present .
Good tips, Thank you for all you do (specially the humor) Love it!!
Ow! That last one looked like it hurt. Thank you. I knew some but not all of these, appreciate you doing this. Now on to your more recent tips video! Wait, I see another one from 2 years ago. And another....
Great tips. Just useful things that I never thought of.
I spied the empty bottle of E.H. Taylor, now the name "Bourbon Moth" makes sense! Entertaining and informative video!
Plugging holes to make a new one: I've always (for several decades anyway) used wood toothpicks. Either round or flat (and occasionally bamboo skewers even though they're really grass and not wood.) Glue it in etc. etc.. Also works on stripped out screw holes.
🤝🤝
Love the tips - they're really great. Especially the zero tolerance fence for the miter saw. I've struggled cutting small pieces.
And shoving the vacuum hose down your pants was the funniest s**t I've seen on you tube. Keep the vids coming.
Just wanted to let you know how much we enjoy your videos. We recommend you often. Keep em coming.
Wow, that first tip was great, I'm using that today!
Not the miter saw jig thingie, I mean the dust extraction hose down the back of the pants when doing a sketchy cut. Can't tell you the number of times _that_ would have come in handy!
Hello sir 🙏🤝🇮🇩🇮🇩
Fantastic work on this video, Jason!
I know a great chiropractor but you will need to come to Texas. Great stuff. I always learn a thing or three. Thanks!
You’re super fun to watch. Love your style. Keep it up!!
I don't know which I liked more.
All the great tips,or all the great falls.😄
New viewer really appreciate the vidios
Man I absolutely love your channel. I love your profession. If I was on my 20s that is what I would do. Thank you for sharing your beautiful wold and teach us to have a little of your talent
Thank you. Hi from Boston. Peter
A brilliant video. Thanks for sharing and being so entertaining. 🌞
I learned all the things. I didn't know about Keith or that really cool arm on the zero clearance board. Let's face it, I am new so I didn't know crap. Love the channel. Off to watch the flooring video I missed.
Great video as always. Thank you so much.
I'm sending a check to you for the splinter removal tip. Never thought of that.
You are a tonic! Thanks
Love the videos. Everything from the Intros, cuts, and advice. Please don't change a thing other than more video's.
Thanks for the miter saw fence tip. And you only said "plop" once! 👍🏼
I always appreciate your tips videos! I had to look up "8 quarter", as I'm still learning the language. Downloaded the app, and plan to add the hold-down clamp to my miter saw fence. I do believe that my favorite tip was in a prior video on how to de-nail pallet wood. That has saved me hours of work! ;-) Love your work!
I like your videos they're very educational . I wonder sometimes how he have not hurt himself yet maybe he has lol. The way he's always throwing himself all over the place.
For others who may not know, a lot of lumber yards will define thickness measurements of wood in quarters of an inch. We all should know that there are four quarters in one inch, four quarters in one dollar, etc. So when the thickness of a board is listed as "8 quarters", what it means is that this is a two-inch thick board. If something is "6 quarters" this means it's one and one-half inches thick. "5 quarters" is one and one-quarter inches". Etc.
@@damionthelwell2032 If you look closely, you might see it's not him being thrown around. He just pops his head up after someone throws a huge dummy on top of him.
That qtip/matchstick trick is brilliant sir thank you
OMG I freaking Love you, you've got me laughing out loud on my lunch at my desk!!!! Keep up the great tips and funny antics
Great tips!!! And beautiful special effects!!
Very useful. Thanks for sharing them.
The vacuum in the pants was very clever! Thanks for the laugh.
Always a fun watch!
I rewatched one of the previous tips video a few days ago and I was thinking we were overdue for a new one :)
100% support dude. Keef it up I learn so from u.
Hey Bourbon... Great thing about the about keeping the grain in mind, when your building. I can, and do, appreciate that!
Keep up the good work, You have good channel you've created here. It's informative, along with some slapstick, and your own brand of dry humor...
You're an absolute kook, and I love it. All great tips. I love woodworking, but suck at it. ALL of these tips are beneficial to me. Thank you and please keep sharing!
Great tips! All of them. Cheers from Oz. 👌
... now i want to see the bloopers of the many running clips xD
The dust hose in the back of your pants had me on the floor 🤣
We need bourbon moth snap backs!
Earned another subscriber you’re sense of humor is spot on
You are the Man.. Love you tips.. You make woodworking fun.. Keep it up dude..
Well done Jason!
Golf tees are my go-to for filling holes in door jamb's. Might work for smaller holes if you shave them down a bit with a knife.
This Video was fantastic very helpful, honest, practical, and also some good comic relief.
Keep up the good work Sir!
I see a bugle tube on your cart! A hunter and a woodworker? A man after my own heart.
Cool videos, thanks for sharing your knowledge 👍
Great idea for chop saw cutting.
Golf tees is the way to go for hole filling 😁
Thank you so much for your tips
Hey you are super helpful.. and energetic! Thank you!!
Fantastic! I am one of the ones that learned from the Q-Tips trick! Thanks!
As a guy that is starting on wood working I’m so glad I bumped on to your channel, great help and great fun! I would love to by you a beer some time. Hey I told my wife I now have a man crush