on throttle rate: I personally always use 30 and try to reduce the agressivness of the motor with other settings (boost, softening, drive freq, timing). Because you need that quick power response. Throttle rate works with a bit of delay and i hate delay. I want the power when i need it. Especially while beeing in the air. This is true especially for 1/10th carpet/astro racing
I have a question about the throttle softening value, when the applied throttle gets above the set range does it instantly snap back to the unsoftened value or does it gradually return the timing to its unsoftened value?
Interesting. Having gone 2.2 with my HW XR10 pro , I've just installed the XR8 pro and I'm hoping it can deliver a lot more amps and get my Losi 22S to a flat 2 on a dry tire . I do like the throttle map using the OTA , similar to my R1 car . Thanks for the info .
@RCstreetwars I do indeed have a question ! I'm running the new large HW drag motor 3662 and I have installed an XR8 pro to run it , I was then told the XR8 pro won't supply turbo or boost timing to this motor ! Is this true ?
@@mattr2533 Before I answer, I will be releasing a new video for the XR10 pro Drag Racing ESC. That is compatible with all motors. As for your question, the XR10 pro series is open to all motors, the rest of the lineup are compatible only with HOBBYWING motors if you want advanced timing.
@@RCstreetwars now I have 30 soft range and 50 value, 20k pwm , throttle rate 15 but at the exit of the corner if i push the accelerator i have too much torque
@@awastyle9198 it sounds like you’re just going to have to take all of your torque reduction tools and set them at the points that produce minimum torque and adjust from there. This includes throttle rate control. Make sure you have your smoothing range and smoothing value set to maximum, I do not recommend any more than 24K PWM.
@@RCstreetwars OK, thanks a lot. you have to adjust the accelerator in every corner to make it accelerate well and not slip. it becomes difficult to be constant on the lap. Throttle curve or speed on radio control can Help?
![Stromae, Pomme - “Ma Meilleure Ennemie” (from Arcane Season 2) [Official Visualizer]](http://i.ytimg.com/vi/1F3OGIFnW1k/mqdefault.jpg)
Hi I'm not sure there's a more thorough video on the Hobbywing settings out there ! Many thanks for the work
Glad you enjoyed it, please ask any questions you might have.
on throttle rate: I personally always use 30 and try to reduce the agressivness of the motor with other settings (boost, softening, drive freq, timing). Because you need that quick power response. Throttle rate works with a bit of delay and i hate delay. I want the power when i need it. Especially while beeing in the air. This is true especially for 1/10th carpet/astro racing
Awesome information, I definitely see that for 1/10 carpet/astro racing
Asome Video How nows the Esc he run a 4 Pole Motor
I have a question about the throttle softening value, when the applied throttle gets above the set range does it instantly snap back to the unsoftened value or does it gradually return the timing to its unsoftened value?
@@stp440 it will decay up to the value,
This way it will not be a sudden change.
Think of it as Anti boost
Interesting. Having gone 2.2 with my HW XR10 pro , I've just installed the XR8 pro and I'm hoping it can deliver a lot more amps and get my Losi 22S to a flat 2 on a dry tire . I do like the throttle map using the OTA , similar to my R1 car . Thanks for the info .
Hope you’re doing well, ask any questions you might have.
@RCstreetwars
I do indeed have a question ! I'm running the new large HW drag motor 3662 and I have installed an XR8 pro to run it , I was then told the XR8 pro won't supply turbo or boost timing to this motor ! Is this true ?
Are the timing parameters also proprietary to HW motors, or can it work on any 2 pole motor? What other parameters will work with any 2 pole motors?
@@mattr2533
Before I answer, I will be releasing a new video for the XR10 pro Drag Racing ESC. That is compatible with all motors.
As for your question, the XR10 pro series is open to all motors, the rest of the lineup are compatible only with HOBBYWING motors if you want advanced timing.
Every time I try to download a file from the ota it freezes at 3%. I can’t figure it out
Will the data logger work on an rtr drag slash?
Yes, if you have the HOBBYWING Esc and the OTA on your Drag Slash.
How can i set my hw g2 xr8 pro to reduce the torque of my 1900kv on buggy 1/8? Thanks
Use the softening valve and range, increase drive frequency or both
@@RCstreetwars now I have 30 soft range and 50 value, 20k pwm , throttle rate 15 but at the exit of the corner if i push the accelerator i have too much torque
@@awastyle9198 it sounds like you’re just going to have to take all of your torque reduction tools and set them at the points that produce minimum torque and adjust from there. This includes throttle rate control. Make sure you have your smoothing range and smoothing value set to maximum, I do not recommend any more than 24K PWM.
@@RCstreetwars OK, thanks a lot. you have to adjust the accelerator in every corner to make it accelerate well and not slip. it becomes difficult to be constant on the lap. Throttle curve or speed on radio control can Help?