Another great lure. I haven’t seen any lure making videos that used electrical tape before. Nice clean lines. I also liked the way you made the wire tie/bill (bib) from the first video. 🙂. Great job! Finished lure looks great! Hope to see it in action.🐟
Thank you 😊 well the electronic tape is great because there is no risk of paint flowing under - so the lines are nice and crisp 😉 all the best from Poland 🤙
Yes, the time saving properties are the biggest advantage 😎 whenever I run late with the project (must be done on Saturday, for editing and uploading on Sunday) UV to the rescue 🦸
Na pewno są najdroższe 😜 więc stosuje tylko i wyłącznie jeśli zależy mi na czasie. Jeśli chodzi o wytrzymałość to mają podobną do żywicy epoksydowej, jedyne co zauważyłem to przy uderzeniu woblerem o beton/most odpada cały kawałek, ale jesli chodzi o drapieżniki, ślady od kotwic to wytrzymałe
@@SuchaJerkCustomLures thak you ... Im also using a .2 nozzle airbrush with acrylic fluid colours.. but the flow was incorrect .. and i cand spray metalic acrylic colours . when i use metalic acrylic colours , it get clogs instantly. .. then i started diluting the colours, there is another problem whic is the colours losses its adhesiveness .. What will be you valuable suggestions for me Brother ?
@@abysahadevan7105 well I would say buy a bigger nozzle - .5mm 👌if you already have serious collection of acrylic colours, if not I would suggest to buy Mr. Colour Japanese paints - if available + dedicated leveling thinner - they work wonders 😉
In terms of casting it actually flies far and stable - I believe the bib works as a stabilizer 👌 in terms of action in the water - no way to see it cause it just dives straight down and I don't have any clear enough deep spot to check it 🤷
Hi, I was planning to add it as always at the end of the video, but the lure was just diving deep immediately and was not visible, based on the water depth, it was still reaching bottom at 3m... unfortunately it stayed there during the first fishing trip 😥
Hola, normalmente incluiría una prueba de natación en cada video, pero aquí el señuelo se sumerge inmediatamente 2 m hacia abajo y no tengo aguas tan limpias para que la acción sea visible 🤷🏻 Solo pude notar que la acción estuvo bien debido a la caña punta agitando correctamente y señuelo nadando recto 😅
@@Furtivo_Lures Sí, cuanto más grande es el labio y el ángulo más agresivo, la resistencia del agua empuja contra el labio y hace que el señuelo se sumerja rápido 😉
W tym woblerze akurat czeburaszka wolframowa - bo z racji na slot łatwiej nadziać na stelaż 👌do tonących woblerów używam kulek wolframowych z AliExpress a do pływających śrutu stalowego 😉
It had stable play, it was just diving straight down, that wasn't good to see what exactly the action was. But based on the rod vibration and braid coming straight it seemed stable. Unfortunately I snagged it during the first 😢 fishing
Another great lure. I haven’t seen any lure making videos that used electrical tape before. Nice clean lines. I also liked the way you made the wire tie/bill (bib) from the first video. 🙂. Great job! Finished lure looks great! Hope to see it in action.🐟
Thank you 😊 well the electronic tape is great because there is no risk of paint flowing under - so the lines are nice and crisp 😉 all the best from Poland 🤙
wow that little bit of gold made such a huge difference this is one of my fav color patterns too love it
Yes it does! thank you :)
Must i call you mister Rembrandt….it seems so easy….your a artist. 👍👍
Thank you 😊 but that's in fact a simple paint job 🙂 there are many custom lure painters around that are much better than me 😉
@@SuchaJerkCustomLures
i know and certainly in Holland but you are one off them
Turnt out so good!
Yes, I'm happy too 🥰 unfortunately no time to fish it for the video because my friends are visiting us...
Brilliant lure👊🎣
Thanks mate 🙂🇵🇱👋🎣
Turned out great! Catch a walleye with it!
Thank you 😊 that's the plan 😊 although here in Europe we have zander which is walleye cousin 😉
Buen trabajo compañero 👌👌. un saludo desde Cádiz, España
Muchas Gracias Juan Carlo 🙏 Saludos desde Polonia 👋👋
Only one word : Sublim ! 😍
Thank you 😊
Amazing work
Thank you 😌🙏
I see you're liking the UV nail polish more and more, is it because it's so handy/convenient and quick? Another great lure, well done!
Yes, the time saving properties are the biggest advantage 😎 whenever I run late with the project (must be done on Saturday, for editing and uploading on Sunday) UV to the rescue 🦸
@@SuchaJerkCustomLures 🙂👍
Cześć. Lakiery UV są wytrzymałe w trakcie eksploatacji, czy może lakiery czy żywice są lepsze? Pozdrawiam
Na pewno są najdroższe 😜 więc stosuje tylko i wyłącznie jeśli zależy mi na czasie. Jeśli chodzi o wytrzymałość to mają podobną do żywicy epoksydowej, jedyne co zauważyłem to przy uderzeniu woblerem o beton/most odpada cały kawałek, ale jesli chodzi o drapieżniki, ślady od kotwic to wytrzymałe
Привет .. Ростова на Дону .благдору за классная видео удачу... Заранее спасибо большое....
Большое спасибо всего наилучшего из Польши 👋
Nice Work . 👍🏻👍🏻
Which airbrush u using to paint the lures ? What is its nozzle size ?
Hard & Steinbeck model Ultra 👌
The nozzle diameter is 0.2mm - for the mid range airbrush - around 100$ - I'm very pleased with the performance 👍
@@SuchaJerkCustomLures thak you ...
Im also using a .2 nozzle airbrush with acrylic fluid colours.. but the flow was incorrect .. and i cand spray metalic acrylic colours . when i use metalic acrylic colours , it get clogs instantly. .. then i started diluting the colours, there is another problem whic is the colours losses its adhesiveness ..
What will be you valuable suggestions for me Brother ?
@@abysahadevan7105 well I would say buy a bigger nozzle - .5mm 👌if you already have serious collection of acrylic colours, if not I would suggest to buy Mr. Colour Japanese paints - if available + dedicated leveling thinner - they work wonders 😉
@@SuchaJerkCustomLures thank u so much 😍😍
Ficou top esta isca artificial artesanal meus parabéns.
Obrigado 🙏 continue fazendo iscas! 💪🎣
Wow amazing... Godbless
Thank you brother 🙏
Świetne malowanie - już widzę jak kropki w niego walą 💪😎👈
Dzięki 🙂 pstrągów to on raczej nie zobaczy w swojej karierze - bo za głęboko schodzi 😝
Racja z takim sterem ale malowanieeee superrrr👌👌👌
Indonesia is Here😁
Hi Isnan 👋 all the best from Poland 🤙 🇵🇱
@@SuchaJerkCustomLures thank you
 Terverifikasi
thank you🇮🇩🤙
Bel video complimenti
Grazie mille Marco 🙏👋🇵🇱🎣
Buen video amigo
Muchas gracias amigo 🙂
Do you know any shops in Poland when you can buy balsa wood?
Niestety mój sklep też ma pustki i tak samo wszyscy dostawcy w Polsce 😟 sytuacja bardzo mocno nieciekawa 🤷
👏🏻👏🏻👏🏻👏🏻
Many thanks 🙏
Top Job 👍👍👍
Thank you! Cheers!
Can you make a spinnerbait lure , I don't know how to make it.Can you teach me😊.
Actually I could 👌 little one for the perch fishing 😁 🎣
Hi there
Lovely job man always
Can u tell me what materials u use for bib
Thanks
Thank you 🙂
Circuit board laminate, in 1mm thickness. here is the link:
52,77 zł | Pick Size / Fiberglass Epoxy Lure Lips, 5pcs, Crankbaits, Lure Making (0.6mm 0.8mm 1mm 1.5mm)
a.aliexpress.com/_vK6EPi
👍👍👍👍👍 здорово 🔥🔥🔥🔥🔥
Большое спасибо 🙂👋🎣
เยี่ยมเลยครับ
ขอบคุณค่ะ🙏
waiting for the report how this hornet flies))))
In terms of casting it actually flies far and stable - I believe the bib works as a stabilizer 👌 in terms of action in the water - no way to see it cause it just dives straight down and I don't have any clear enough deep spot to check it 🤷
Boa tarde esse líquido transparente e o que? Qual o nome? Gostei muito
🧨🧨🧨🧨🧨🧨🧨
🙏💜😉
Test action broo??
Hi, I was planning to add it as always at the end of the video, but the lure was just diving deep immediately and was not visible, based on the water depth, it was still reaching bottom at 3m... unfortunately it stayed there during the first fishing trip 😥
Show , trabalho perfeito
Muito obrigado 🙏
Muito obrigado 🙏
😍✌️
🙏👌💜
I need this lure for trolling😭
I already snagged it 😭 on first session after maybe half an hour 😖
MODEL BARU YA SEMAKI BANYAK KOLEKSI LURNYA
terima kasih saudaraku 🙏
@@SuchaJerkCustomLures sama ama saudaraku
😍✌️🙏
Thank you brother 🙏
Maravilhosa 👍👏👏👏
🙂👋🇵🇱🎣
No ha llegado video de prueba de nado?saludos desde CR, pura vida
Hola, normalmente incluiría una prueba de natación en cada video, pero aquí el señuelo se sumerge inmediatamente 2 m hacia abajo y no tengo aguas tan limpias para que la acción sea visible 🤷🏻 Solo pude notar que la acción estuvo bien debido a la caña punta agitando correctamente y señuelo nadando recto 😅
2 metros!!! Increíble!lo curioso es que casi no lleva peso...dirías que depende casi enteramente de la paleta?
@@Furtivo_Lures Sí, cuanto más grande es el labio y el ángulo más agresivo, la resistencia del agua empuja contra el labio y hace que el señuelo se sumerja rápido 😉
👍👍👍👍👍👍👍👍👍👍👍👍👍
🙂🙏👋🎣
Skąd bierzesz obciążenie?
W tym woblerze akurat czeburaszka wolframowa - bo z racji na slot łatwiej nadziać na stelaż 👌do tonących woblerów używam kulek wolframowych z AliExpress a do pływających śrutu stalowego 😉
I made a minnow once... Then i stopped and buy a finish product.
Because my minnow Always Flip to the right,,😂
In case there line tie is not in the lure lip you can adjust the ection by bending it opposite direction that your lure escaping 😉
Круть!
Спасибо 🙂
101' like))
Thank you 🙂
Рыскание из стороны в сторону,нестабильная игра, -носовая петля низко посажена.
It had stable play, it was just diving straight down, that wasn't good to see what exactly the action was. But based on the rod vibration and braid coming straight it seemed stable. Unfortunately I snagged it during the first 😢 fishing