I don't have time to watch this now, but I just wanted to say that I'm super f*ckin excited to watch it. Old school RUclips. What RUclips was made for.
Reminds me of my first snowpony, mid 70's Arctic Cat Lynx with a single cylinder 300cc Rotax stuffed in courtesy of my old man. I believe he had to reclock the exhaust can, make custom engine mounts to get belt deflection close enough to not chew stuff...man I miss those days🤤
The old john deere sounds awesome but i have a question for you , i have a old 72 atric cat cheetha 399 i know nothing about it i put a mukini carb on it that sits at that stupied angle like you said and the first time i start it it takes right off runs great but when i shut it off and try starting it again 1 minute latter it is flooded . Does that sound like bad crank seals thanks
I have done wvery thing you said about swaping me tiltonsnn carb ti a munkuni carb it is a 399 kowosuki motor running a 300 main jet it starts good cold and sounds great but when i shut itcoff and try to restart it it floods instantly is that a bad needle and seat thanks
How bad is it flooding, just enough to not run, or like geysers of gas out the plug holes almost hydrolocking? If the first, will it fire with the throttle held open a bit? If so, smaller pilot jet
@@toocheaptosmoke it will fire a few times then flooded the plugs are wet then what size piolet jet would you recomend starting with the carb is off a 340 blizzerd and i dont know what size it is
Now i lowered the carb and it starts and runs good with the minkini carb but when it idles after 15 to 20 seconds it floods out it runs good when i give it a little throttle is my needle set ro high
The brass float arm should be set to sit parallel with carb body when held upside down. If your carb(s) are vibrating or shaking alot at idle it can also flood out, dampen zip tie or bungee them to something. Or needle and seat could also just be worn
no, the small pilot jet down inside the carb, they are sized around 20-50. Check out a mikuni diagram and you can see where it's located, you need a small screwdriver
I don't have time to watch this now, but I just wanted to say that I'm super f*ckin excited to watch it. Old school RUclips. What RUclips was made for.
im glad you posted i was worried you left youtube
Haha, naw still here. Should be doing my taxes instead of youtube videos though...
i been riding my SS indy 94 . white with blue and pink detailing . its a beast. you would approve
You are the best, entertaining, innovative, etc. You are much appreciated!
Ifn you aint got it make it ur motto,real nice mr.dangles!!snooky pa
"Screwdrivers, pickled eggs, pork rinds and belts scattered all over the hill"
That shits funny lol
This thing is bad ass. I’m both a skidoo and John Deere fan. This is absolutely perfect
Reminds me of my first snowpony, mid 70's Arctic Cat Lynx with a single cylinder 300cc Rotax stuffed in courtesy of my old man. I believe he had to reclock the exhaust can, make custom engine mounts to get belt deflection close enough to not chew stuff...man I miss those days🤤
Nice to see a project finally get to the snow and be badass
Thanks man, I hear ya!
Really cool to see that ext hood you bought from me at A1 in the video my man. Love the awesome content!
Haha, glad you noticed that!!
Great as always
Appreciate it. 👍
Groil - also an excellent wood stain and concrete sealer.👍
Love watching your videos man!
Thanks man!
How did i miss this video??? Speed dust removal lmao
Just ran my supplies empty at work? Half hour video from my fucking dude?
Cool, I’m in.
Love the hauling rig in that one picture, so cool 😎
Thanks 👍
👌 thanks for another great video!!
Nice! Exhaust sounds great. Definitely needs more wires.
Yeah, lol
I have some polaris 151 rails I'd sell for you to have some full rails I'm from Michigan and was at a1 as well.
Always happy to see that you have a new video - Could watch these all day long! Cheers from Québec 👍
Cheers! 👍
The old john deere sounds awesome but i have a question for you , i have a old 72 atric cat cheetha 399 i know nothing about it i put a mukini carb on it that sits at that stupied angle like you said and the first time i start it it takes right off runs great but when i shut it off and try starting it again 1 minute latter it is flooded . Does that sound like bad crank seals thanks
Probably not crank seals if it floods. put the front end up on a few pallets and see if it starts then
@@toocheaptosmoke you werecright as usual im putting a trundra boot on they drop the carb a couple inches cause they make a bend thanks
@@bobnewman9493 👍
That’s not oil and grease on there! It’s groil and ease!!!
Tell us about that polaris charger in the beginning. My main vintage sled is a 73 charger 400. I have a video of it on my channel
That's another project firmly lodged in purgatory... Got it a while back, it's a 530 fan, needs drivers, and some motivation.
@toocheaptosmoke nice I used to have a 530 polaris custom...was a beast
Bitchin🤘🏻!
I have done wvery thing you said about swaping me tiltonsnn carb ti a munkuni carb it is a 399 kowosuki motor running a 300 main jet it starts good cold and sounds great but when i shut itcoff and try to restart it it floods instantly is that a bad needle and seat thanks
How bad is it flooding, just enough to not run, or like geysers of gas out the plug holes almost hydrolocking? If the first, will it fire with the throttle held open a bit? If so, smaller pilot jet
@@toocheaptosmoke it will fire a few times then flooded the plugs are wet then what size piolet jet would you recomend starting with the carb is off a 340 blizzerd and i dont know what size it is
Its a 34mmcarb but i dont know what piolit jet is in it
@@bobnewman9493 30 pilot is probably a good starting point
gonna buy me some groil! XD
Now i lowered the carb and it starts and runs good with the minkini carb but when it idles after 15 to 20 seconds it floods out it runs good when i give it a little throttle is my needle set ro high
The brass float arm should be set to sit parallel with carb body when held upside down. If your carb(s) are vibrating or shaking alot at idle it can also flood out, dampen zip tie or bungee them to something. Or needle and seat could also just be worn
@@toocheaptosmoke thanks
Bushing out of electrical tape 😂😂😂😂
You mean 130 piolit jet there is a 150 on it now i took a bunch apart and the smallest i found is a 135
no, the small pilot jet down inside the carb, they are sized around 20-50. Check out a mikuni diagram and you can see where it's located, you need a small screwdriver
@@toocheaptosmoke i know what the piolit jet is maybe its a letter i or l in front of the number i will try to get a 30 thanks
Similar voice and hand gestures as Zipties And Biasplies lol
Team Arctic, on a Deere, with a Rotax in it. Lol, perfect. It's almost an AMC, all makes combined.
Lol, track and suspension is Polaris, tunnel extension is yamaha!
you got a bobcat? :)
CASE: can't afford something else...
👌👌👌
i need me some Groil
What a beaut!
Bit of a shame the snow washed off a lot of speed dust...
@@toocheaptosmokeOui oui, Sacrilege
80hp to 118 hp ?
Probably somewhere in there... Lol
Zip ties and bias plies!!!!
"Promo sm" 🌷
First
id like to buy 100 gallons Groil