With all the tropical plants down here in Florida I use the 2.3 however I do use a 2.1 when the algae gets super bad, great video Mike. Downstream is a fantastic way to clean.
Here's my message I pass along on Facebook and Reddit about this subject the 1.5mm, 1.8mm, 2.1mm, 2.3mm, 2.5mm is the orifice size that's inside the injector. This varies your draw rate. These are general pump sizes Metric-Inches- similar tip size 1.45mm-0.057"-(5) 1.5mm-0.059"-(5.5) 1.6mm-0.063"-(6.25) 1.8mm-0.071"-(8) 2.1mm-0.083"-(11) 2.3mm-0.091"-(13) 2.5mm-0.098"-(16) The smaller the orifice means higher pressure which means a stronger draw through the venturi effect Also like an xjet your gpm is also going to vary your dilution ratio.
@@TheFreshRinse they both work hand in hand with each other because just like nozzles smaller orifice means higher pressure and lower gpm so it's less diluted but also at the same time higher pressure from the smaller orifice is creating a stronger vaccum through the Venturi effect on the other size of the orifice where the barb is bringing in chemical faster. I would say with a stock injector that has the same barb size, the orifice makes the bigger difference in dilution more than the pressure created vacuum does. Reason being, the barb could and probably does restrict how much more chemical could come in with the higher pressure created vacuum. If the barb were larger to not cause restriction on the chemical intake then I would say the pressure causing vacuum would be what makes a stronger mix more than the amount of flow the orifice allows.
I soft washed my house (well x-jet) for the first time this weekend. Thank you for your videos…. I saw my neighbors watching, wondering “what is the mysticism?” Seriously tempted to go into business for myself!
Like your video/info. Mike 👍 And Yep, ordered & changed back to 2.3 DSI last month for my 8gpm as well after a few mishaps in this heat. FYI, a Gardener said that even watering plants if very hot, direct sun, dry conditions can cause problems with plants. Recommends a very Light mist/fog to cool, second heavier mist to wet, and even a third pass to soak… then you can wash/ rinse. Im also adding a neutralizer for a secondary pre or post treatment. It’s definitely more work/time/cost but, I can’t afford to destroy any more plants. 😢
@@TheFreshRinse I am looking to get the raw chem (can’t recall tech. name) and mix my own, I was using “Agent Halt” from The Power Wash Store in Nashville when I started out but there are several brands on the market.
I appreciate the test and it gets me re-evaluating my own process. I have ordered by accident when I didn't know any difference; the 2.3 and didn't notice any difference. But something to consider in your own process is that when I am using a 2.1, I am typically using a batch mix of about 10% SH, so that means that my off the gun mix is probably about 1% with the 2.1 and when you did your house-wash with straight bleach and a 2.3 orifice, you are probably also about 1% off the gun. So there are different ways to accomplish the same thing and I think your test is about exactly what I would have expected. As an additional point, I have never felt the need to switch the orifice size and have just accepted that my hottest mix is going to be about 1.2% and if I need hotter then I switch to a roof pump or XJet and so far that has been fine.
You are probably right, I just assume when it is cleaning good then it is in the 1% zone. Well I can also tell by the amount of sting in my eyes between hot and not. Super scientific I know.
I agree with your field data. I have only used a 2.3 with a igx 800 10gpm. When it is in the 60degree range and less I usually have to reapply the solution. Good video. Good suggestions.
I exclusively use 2.3 during spring and summer and I'm super fast and efficient. I even sometimes close my 3 way valve to my bleach a tad. Come late fall and early winter I go with a 2.1 or 1.8. the comments that state that a 2.3 is a chemical saver are spot on and I get the same, fast results during warm weather
Did the homeowners say you killed plants or did you notice? I haven’t killed anything in 2 years other than my own grass at home when priming my 12v lol. But seriously just wondering. I bought a 1.8 injector and didnt even think to be more careful on plants. Does that 1% if even 1% make that much difference on plant life?
Yeah, pretty much. I’ve killed a few. I never argue. If they feel the plant(s) are toast, I say “Please let me know what I can do to help resolve the situation. I’ll stop at nothing to make it as right as I possibly can.”
I’ve heard of guys that work that way, one guy soaps the other follows and rinses, (some guy up in CT maybe, LOL) my son and I just divee it up when we arrive, “ I’ve got near and rear, you do front and far”. As a solo act Fresh, you get to drag your two guns and hoses around and soap and rinse at the same time. Good luck not running out of water with an 8 and 10 sucking you dry at the same time. We run 2 6s and struggle to maintain water in the tank, or as Joe says, “chasing water”. Keep up the great work guys!
I heard a rumor that you don't use surfactant on roof washs anymore? Is that true and why if it is? I am new to the game and have done to roof washes both was her fact that I'm wondering if the extra expense is necessary.
The orifices from there Not a dollar Each. They are 3.50 each Plus shipping. If you happen to find them anywhere for a dollar, let me know cause I need to buy some more. Thank
I determine it by the temperature. Sounds crazy but, when it’s cold I use the 1.8 because it’s more potent. When it’s warm I use the 2.1. And when it’s hot outside I use the 2.3
Would you say that a 10gpm would be too much? I'm thinking that a 10 could be quite versitile if configured properly: you can do both flatwork and house washing without having to jump around between different machines. Just thinking out loud.. let me know what you think
@@TheFreshRinse Yes, I can imagine with all of that power! Would you recommend using dedicated softwash systems for roofs/houses and just downstream for flatwork?
@@jonmitchell9213 I have an 8 for house washing, a 10 got flat work, an AR 45 for roofs and pretreatment and postreatment of concrete and a 12 volt for roof washing.
@@jonmitchell9213 I’m extremely minimalistic in my approach… yet efficient. No fancy knobs and switches. At 53, I just want to get the job done. Nothing very impressive.
@@TheFreshRinse yes….you did say that. I was thinking for you long term, 2.1 would be the go to injector for 8 gpm. I’ve tried 2.3 myself…..seems like longer wait times and more applications, but that’s me. Thanks for the videos, their great.
Maybe you killed the plants like I did that one time on a house because I forgot that I did not switch my down the stream injector back to rinse 🤣🤣🤣🤣 talk about a big "oops"
Did a similar thing when prepping to wash a deck and started by wetting down the white cedar siding 🤦♂️ Fortunately the owners liked the "fresh" look they got along the back of the house. They even asked for a price to do the whole thing 💪
With all the tropical plants down here in Florida I use the 2.3 however I do use a 2.1 when the algae gets super bad, great video Mike. Downstream is a fantastic way to clean.
Thank you my brother. You do a ton of work!
Get after it
11:15 … You mean Russ Johnson at South Side Equipment.
Which btw, I’m fortunate enough to live 20 minutes from him. 😊
As always, great video Mike. ✌🏼
Yeah, I caught that after I uploaded the video
I need to get me a few different orfices now.Between those and the ball/spring rebuild kits I think the injector housing will last a good long while!
Absolutely
Here's my message I pass along on Facebook and Reddit about this subject
the 1.5mm, 1.8mm, 2.1mm, 2.3mm, 2.5mm is the orifice size that's inside the injector. This varies your draw rate.
These are general pump sizes
Metric-Inches- similar tip size
1.45mm-0.057"-(5)
1.5mm-0.059"-(5.5)
1.6mm-0.063"-(6.25)
1.8mm-0.071"-(8)
2.1mm-0.083"-(11)
2.3mm-0.091"-(13)
2.5mm-0.098"-(16)
The smaller the orifice means higher pressure which means a stronger draw through the venturi effect
Also like an xjet your gpm is also going to vary your dilution ratio.
Thank you. Are you sure it’s the small hole/pressure combo that draws a different ratio? Or, is it large hole adds more water, thus diluting the mix?
@@TheFreshRinse they both work hand in hand with each other because just like nozzles smaller orifice means higher pressure and lower gpm so it's less diluted but also at the same time higher pressure from the smaller orifice is creating a stronger vaccum through the Venturi effect on the other size of the orifice where the barb is bringing in chemical faster. I would say with a stock injector that has the same barb size, the orifice makes the bigger difference in dilution more than the pressure created vacuum does. Reason being, the barb could and probably does restrict how much more chemical could come in with the higher pressure created vacuum. If the barb were larger to not cause restriction on the chemical intake then I would say the pressure causing vacuum would be what makes a stronger mix more than the amount of flow the orifice allows.
I soft washed my house (well x-jet) for the first time this weekend. Thank you for your videos…. I saw my neighbors watching, wondering “what is the mysticism?” Seriously tempted to go into business for myself!
Thank you for watching brother!
Like your video/info. Mike 👍
And Yep, ordered & changed back to 2.3 DSI last month for my 8gpm as well after a few mishaps in this heat.
FYI, a Gardener said that even watering plants if very hot, direct sun, dry conditions can cause problems with plants. Recommends a very Light mist/fog to cool, second heavier mist to wet, and even a third pass to soak… then you can wash/ rinse.
Im also adding a neutralizer for a secondary pre or post treatment. It’s definitely more work/time/cost but, I can’t afford to destroy any more plants. 😢
You are the best. Thank you. May I ask what neutralizer you are using?
@@TheFreshRinse
I am looking to get the raw chem (can’t recall tech. name) and mix my own, I was using “Agent Halt” from The Power Wash Store in Nashville when I started out but there are several brands on the market.
I appreciate the test and it gets me re-evaluating my own process. I have ordered by accident when I didn't know any difference; the 2.3 and didn't notice any difference.
But something to consider in your own process is that when I am using a 2.1, I am typically using a batch mix of about 10% SH, so that means that my off the gun mix is probably about 1% with the 2.1 and when you did your house-wash with straight bleach and a 2.3 orifice, you are probably also about 1% off the gun. So there are different ways to accomplish the same thing and I think your test is about exactly what I would have expected.
As an additional point, I have never felt the need to switch the orifice size and have just accepted that my hottest mix is going to be about 1.2% and if I need hotter then I switch to a roof pump or XJet and so far that has been fine.
💯 % agree!!!
You are probably right, I just assume when it is cleaning good then it is in the 1% zone. Well I can also tell by the amount of sting in my eyes between hot and not. Super scientific I know.
@UtahPressureWashing I’d say your numbers are close.
@@bearnakedbull There’s nothing overly complex about what we do. The ol “sting in the eye” trick works most times.
You can change the orifice out with the quick connects on. Asduming your allen key is long enough.
I’m in the habit of removing it because I used to have the plug on that end. But yes, you are 100% correct!
I agree with your field data. I have only used a 2.3 with a igx 800 10gpm. When it is in the 60degree range and less I usually have to reapply the solution. Good video. Good suggestions.
I’m grateful. Thank you!!!
I exclusively use 2.3 during spring and summer and I'm super fast and efficient. I even sometimes close my 3 way valve to my bleach a tad. Come late fall and early winter I go with a 2.1 or 1.8. the comments that state that a 2.3 is a chemical saver are spot on and I get the same, fast results during warm weather
100% correct
@derrickslodysko963 That will work
Did the homeowners say you killed plants or did you notice? I haven’t killed anything in 2 years other than my own grass at home when priming my 12v lol. But seriously just wondering. I bought a 1.8 injector and didnt even think to be more careful on plants. Does that 1% if even 1% make that much difference on plant life?
I’ve had several customers call. I get it. It doesn’t seem right. I can only chalk it up to the severe lack of rain.
Another knowledgeable video! Thanks Mike
@@kmc669 You are very welcome brother
Thanks Mike great information to know.
Thank you my friend
I've been using a 1.8 with my 5gpm. Been working great
That’s a powerful combo
@TheFreshRinse Yea, I have been sure to wet everything very well, so far I've haven't had any issued lol. I may switch back to the 2.1
Love this information for sure.
Very valuable.
Thank you my friend!
Keep up the hustle Fresh!
BOOM!
Great video mike! Very informative!
Thank you brother!
Great Detail. Thank you! Question… how do you handle customer when killing plants? Do you offer replacements right from the start?
Yeah, pretty much. I’ve killed a few. I never argue. If they feel the plant(s) are toast, I say “Please let me know what I can do to help resolve the situation. I’ll stop at nothing to make it as right as I possibly can.”
Great video Mike !
Thank you Enda
You should check out the pipe vise portable vise. I bought one. Really like it!!!
I’ll have to do that. Thank you?
Amazon for the vise?
Hey Mike! Wouldn’t you be better off doing a better job watering plants than changing the size of the injector?
That’s a great question Jose. As the temperature rises, a strong mix is not as necessary. Perhaps doing both would be beneficial.
Awesome brother!
Thank you kind sir!
Running 12% 3500 hp 4 gpm downstreaming 100ft hose is a safe for vinyl
@@williamlamendola-xi5eq Yes, that will work
Thanks learning a lot from you easily to understand the way you simplify
Great information Mike!
A new channel?? Oh yea!!
Thank you good man!
any way to test the water to get an exact mix ratio? pH testing strips or something?
It’s a great question. I’m sure… but in the end, if it eliminates the organic growth, it’s strong enough. Still a great question.
What size injector would you recommend for a 4gpm?
2.1 or 2.3
@@TheFreshRinse
Thank you for answering so many question.
Where do you buy the replacement orifices?
Southside Equipment in Kentucky.
@@TheFreshRinse Thanks sir
5.5 comet pump with a 3 orfice in a super sud sucker is getting a 14:1. That with 12.5 sh gives 0.8% final.
Nice!!!
It’ll never work, now it’ll take all day. You should use the 1.5 so you can soap and then rinse instantly 😂
Come to think of it, I have two machines. I should soap with one (1.5) and rinse with the other… at the same time!
@@TheFreshRinse why haven’t you been doing that all along
I’ve heard of guys that work that way, one guy soaps the other follows and rinses, (some guy up in CT maybe, LOL) my son and I just divee it up when we arrive, “ I’ve got near and rear, you do front and far”. As a solo act Fresh, you get to drag your two guns and hoses around and soap and rinse at the same time. Good luck not running out of water with an 8 and 10 sucking you dry at the same time. We run 2 6s and struggle to maintain water in the tank, or as Joe says, “chasing water”. Keep up the great work guys!
@@brianaird2193 I’m using the new waterless X12 hydroblaster 2.0.
@@brianaird2193 always chasing
I heard a rumor that you don't use surfactant on roof washs anymore? Is that true and why if it is? I am new to the game and have done to roof washes both was her fact that I'm wondering if the extra expense is necessary.
See for yourself!
ruclips.net/video/AEvbAUEq24o/видео.htmlsi=4D4tWjHD27a5w5rM
What plants were you killing? Tomato plants by chance? That's about the only thing I've had issues with
Nothing in particular. It’s just been so crazy dry.
The orifices from there Not a dollar Each. They are 3.50 each Plus shipping. If you happen to find them anywhere for a dollar, let me know cause I need to buy some more. Thank
Prices increase all the time. I would encourage you to buy them at $3.50 as you can. $3.50 is the new $1.00
How do you determine SH percentages when using the different orifices wirh different gpm machines?
I determine it by the temperature. Sounds crazy but, when it’s cold I use the 1.8 because it’s more potent. When it’s warm I use the 2.1. And when it’s hot outside I use the 2.3
Would you say that a 10gpm would be too much? I'm thinking that a 10 could be quite versitile if configured properly: you can do both flatwork and house washing without having to jump around between different machines. Just thinking out loud.. let me know what you think
I love my 10, and use it from time to time for house washing. It’s a bit overkill. It can ware out your arms.
@@TheFreshRinse Yes, I can imagine with all of that power! Would you recommend using dedicated softwash systems for roofs/houses and just downstream for flatwork?
@@jonmitchell9213 I have an 8 for house washing, a 10 got flat work, an AR 45 for roofs and pretreatment and postreatment of concrete and a 12 volt for roof washing.
@@TheFreshRinse Awesome! Sounds like a solid set up
@@jonmitchell9213 I’m extremely minimalistic in my approach… yet efficient. No fancy knobs and switches. At 53, I just want to get the job done. Nothing very impressive.
So I should stick with the 2.1 with my 5.5 gpm
Yes sir
2.3 works gtreat above 70 for sure
Yes. You are correct.
What unloaders do you run?
VRT3
Well, I am surprised that it took 3x to hit it to get that algae off which wasn't that bad..Too much time for me..But thanks for the video
2 times, not 3.
Are you running a half inch injector bypass off your 8gpm or is it all 3/8?
@@DiamondHandsDetailingLLC 3/8”
For a 2.8 gpm pump do recommend a 2.3 if I am trying to get closest to that 1% mark?
You can go ad low as you want. A 1.8 will work. Probably a 1.8 would do great.
@@TheFreshRinse Would I get a higher or lower percentage if I went to a 2.3?
What brand DS injectors do yoy buy? Does it matter the brand are the orfaces universal.
I have 2.1 GP injectors.
I buy GP
How long will the M5 twist last? It’s oraficessss will enlarge as well
You are correct. I’m currently using last year’s. But I should probably update
I would rather put a slightly stronger mix down and not have a call back
Perhaps you missed the first minute of the video. LOL
@UtahPressureWashing LOL
@@TheFreshRinseI'm extra careful w plants and just really make
Sure to pre rinse; post rinse, and rinse rinse the plants 🤣
@@jayslo914 I should consider doing that. LOL
@UtahPressureWashing😅
You’ll go back to the 2.1 😉
I believe I mentioned that I would on the really dirty houses, and when it’s cold.
@@TheFreshRinse yes….you did say that. I was thinking for you long term, 2.1 would be the go to injector for 8 gpm. I’ve tried 2.3 myself…..seems like longer wait times and more applications, but that’s me. Thanks for the videos, their great.
@@simplycleanpressurewashing758 2.1 seems more legit, in my opinion. I agree.
What's new channel called?
I’m not sure yet. In the works as we speak
At 2:38 you messed up and said you're changing from a 2.1 to a 1.8 whereas you were supposed to change to the 2.3
I hate myself so much right now already!
Maybe you killed the plants like I did that one time on a house because I forgot that I did not switch my down the stream injector back to rinse 🤣🤣🤣🤣 talk about a big "oops"
I’ve done that before with my AR45. Big mistake
Did a similar thing when prepping to wash a deck and started by wetting down the white cedar siding 🤦♂️
Fortunately the owners liked the "fresh" look they got along the back of the house. They even asked for a price to do the whole thing 💪
@@deadfishporter I forget all the time to pre-wet fences that bump up against the house.
@@TheFreshRinse I'm glad I'm not the only one with a sieve for a brain 🤦♂️