Thank you very much!, His way of explaining is very encouraging, I started from 0, and it is so easy to understand him.(and with translated subtitles) is big!
Thank you for improving over the years on your content information and how you present it. Is it posable to do a Klipper video on a 3 in to 1 shared nozzle setup with a BTT Octopus with a non Pi like a Rock Pi4? This will help me solve the extruder setup and how to get the power function to work on a non pi... I can not get access Via Klipper to the Rock Pi 4 GPIO ports.... (cli commands work good) I am tired of have to use the SD card to print in Marlin VS the usb due to the protocol overhead on the usb bus, printing faster then 90mm/s.... I fell in to the rabbit hole of klipper and ran out and back to Marlin for a few jobs I had to print. I solved all but the 3 in to 1 and the power issue (the power issue I did find a workaround , but not what I wanted) If you can help me understand the 3 in to 1. Not just coding but how / why the code works that way. I will make sure I "Like" it.
Hey Chris I realy like you MKS Skipr install videos. I used this series to set up my board. I have a question, can you make a video about how you setup an EBB 36 CAN- Thoolhead Board on der MKS skipr. I already searched on google but I couldnt find a good howto (and I am bad at coding). So if you or someone else knows a good instruction or a vid I would realy appreciate it if I can get to it.
Any chance you can make a video of using BLtouch with these boards? upgrading from a SKR Mini e3 v2 and am lost on how i should attach this sensor Thanks!
@@ChrisRiley appreciated, your videos helped me to my first marlin compile and flash and now these videos have been invaluable in helping me learn klipper, thanks a ton!
@@ChrisRiley Upon looking heavily into the topic there is a 3 pin header on the board marked 3dtouch next to the two LCD headers, After hooking the control,5v and ground to that header and the switch and ground pins to an endstop header and defining the sensor pin to ^PA13 and control pin to PA8 under [bltouch] aswell as setting Z endstop to Z_virtual_endstop now everything works perfectly, hopefully this information can help somebody else.
Hello Chis. Very good explanations on all your videos. I'm having a crash with this messagem "Unable to read tmc uart 'stepper_x' register IFCNT". I have a TMC2240 and i can't find how to make the jumpers and the kippler configurations! Hope you can help me.
Thank you! I don't know much about the 2240's yet, my guess is they have a different set of pins they use to talk to the board. I will see if I can get some info on them.
@@ChrisRiley That's right, I see people saying it's plug and play but really I need someone to guide me, I hope you can share more information about it, and how to install it in the config file in klipper. Sorry I can't add the link to youtube but you can find it at mks github or gg it as mks servo42c 42c v1.1
Do you know how to connect the CR-Touch to this board? The cable is black and has 5 pins. I see the 3D Touch slot but that’s only 3 pins. Where do the other two pins go? What are the pin outs?
To make it work, the 5 pins have to be broken out. 3 go to the probe/servo pins, 2 go to z min endstop. support.th3dstudio.com/helpcenter/crtouch-sensor-pinout-sensor-side/
@@ChrisRiley Do you know of a port/slot/location on the board that will give me 12/24v, like the power port, but I can turn it on/off via code in Klipper?
Great video but it seems like a steep climb. It would be great if there was an "EZ Klipper" interface / compiler so I just entered what I needed and it did the rest.
This is my first attempt at anything like this. Very overwhelming, but you break it down so that I can follow you. However, I am stuck. My sensor is not stopping the z axis. When I try to home it, it crashes into the print head and continues to try to move up until I hit the emergnecy stop. I have adjusted teh z offset all the way to 5 mm after rechecking all the steps up to this point. Nothing seems to be working. Please help!
I figured it out. The tronxy TR sensor is not 5V. I changed the sensor to the Z+ slot, changed the pin to PB14, and changed the the Z+ jumper from 5V to VIN.I can now home all.
good evening, I'm getting the TMC error 'stepper_z' reports error: DRV_STATUS: 40190004 s2ga=1(ShortToGND_A!) cs_actual=25 stealth=1, I'm using the tmc2226 drivers, 24v 1.3A 0.9° nema17 motors, I really don't know to do
@@ChrisRiley gracias a ti por dar una explicación tan detallada hace tiempo que tenia la palca mks skipr pero siempre me daba errores, pero con lo que vi en tus videos me aclaraste muchas cosas excelente serie espero poder ver mas sobre la placa mks skipr
Thank you very much!,
His way of explaining is very encouraging, I started from 0, and it is so easy to understand him.(and with translated subtitles)
is big!
I'm happy to help! Thank you for watching
I thought I was in way over my head but this series saved me! Thanks!
Glad to hear it! Thank you
Do you have any video how about the can comunication in THR board from MKS?? Thanks in advance for your awesome works
I don't, but I think I have one. I will see what I can do.
@@ChrisRiley thanks ;)
Thank you for improving over the years on your content information and how you present it. Is it posable to do a Klipper video on a 3 in to 1 shared nozzle setup with a BTT Octopus with a non Pi like a Rock Pi4? This will help me solve the extruder setup and how to get the power function to work on a non pi... I can not get access Via Klipper to the Rock Pi 4 GPIO ports.... (cli commands work good) I am tired of have to use the SD card to print in Marlin VS the usb due to the protocol overhead on the usb bus, printing faster then 90mm/s.... I fell in to the rabbit hole of klipper and ran out and back to Marlin for a few jobs I had to print. I solved all but the 3 in to 1 and the power issue (the power issue I did find a workaround , but not what I wanted) If you can help me understand the 3 in to 1. Not just coding but how / why the code works that way. I will make sure I "Like" it.
I try to do my best! 😀 I will look around and see what I can find to test a config like this. Thanks for the suggestions.
@@ChrisRiley Thank you.. If it helps I can send you my work in progress. I just am at a blocking point of my experience in this.
I have nothing to say, just want to get a comment in early! 😆. I’ll get to watching when I get outta work. Thanks Chris 😊
🙂👍 Thanks for watching!
Hey Chris I realy like you MKS Skipr install videos. I used this series to set up my board. I have a question, can you make a video about how you setup an EBB 36 CAN- Thoolhead Board on der MKS skipr. I already searched on google but I couldnt find a good howto (and I am bad at coding). So if you or someone else knows a good instruction or a vid I would realy appreciate it if I can get to it.
I've never done any videos on the tool boards yet, but I need to. I will look into this one.
Very informative. Can It load any other OS other than Ambiant? I believe Pi4 can load any flavor of Linux?
Thanks! For this one, Armbian is the only OS this chip can run.
If you set position_min to -33 you can set position_endstop to -33, then 0 would be correct for the y-axis.
Awesome! Thanks for the tip!
Any chance you can make a video of using BLtouch with these boards? upgrading from a SKR Mini e3 v2 and am lost on how i should attach this sensor
Thanks!
I'll see what I can do!
@@ChrisRiley appreciated, your videos helped me to my first marlin compile and flash and now these videos have been invaluable in helping me learn klipper, thanks a ton!
@@ChrisRiley Upon looking heavily into the topic there is a 3 pin header on the board marked 3dtouch next to the two LCD headers, After hooking the control,5v and ground to that header and the switch and ground pins to an endstop header and defining the sensor pin to ^PA13 and control pin to PA8 under [bltouch] aswell as setting Z endstop to Z_virtual_endstop now everything works perfectly, hopefully this information can help somebody else.
So what is the voltage supposed to be coming out of the endstops. I'm getting @.05v. I thought they were supposed to be 5v.
It depends on the board, but you should get 5v when it's triggered from the GPIO pin. You can flip that in the firmware as well.
Hello Chis. Very good explanations on all your videos. I'm having a crash with this messagem "Unable to read tmc uart 'stepper_x' register IFCNT". I have a TMC2240 and i can't find how to make the jumpers and the kippler configurations! Hope you can help me.
Thank you! I don't know much about the 2240's yet, my guess is they have a different set of pins they use to talk to the board. I will see if I can get some info on them.
Can you show me how to use mks servo42c driver, how can i plug it into mks skipr board and install in klipper
Are you talking about the closed loop stepper module? Do you have a link?
@@ChrisRiley That's right, I see people saying it's plug and play but really I need someone to guide me, I hope you can share more information about it, and how to install it in the config file in klipper. Sorry I can't add the link to youtube but you can find it at mks github or gg it as mks servo42c 42c v1.1
Do you know how to connect the CR-Touch to this board? The cable is black and has 5 pins. I see the 3D Touch slot but that’s only 3 pins. Where do the other two pins go? What are the pin outs?
To make it work, the 5 pins have to be broken out. 3 go to the probe/servo pins, 2 go to z min endstop. support.th3dstudio.com/helpcenter/crtouch-sensor-pinout-sensor-side/
@@ChrisRiley Do you know of a port/slot/location on the board that will give me 12/24v, like the power port, but I can turn it on/off via code in Klipper?
goddamn can a brother get some zip ties.. a bread tie a shoelace whatever to clean up those wires lol
Lol! I've never been very good at keeping house!
Great video but it seems like a steep climb. It would be great if there was an "EZ Klipper" interface / compiler so I just entered what I needed and it did the rest.
Great suggestion!
This is my first attempt at anything like this. Very overwhelming, but you break it down so that I can follow you. However, I am stuck. My sensor is not stopping the z axis. When I try to home it, it crashes into the print head and continues to try to move up until I hit the emergnecy stop. I have adjusted teh z offset all the way to 5 mm after rechecking all the steps up to this point. Nothing seems to be working. Please help!
Still can’t get past this part. If anybody has any ideas, that would be awesome. I have the original tronxy tr sensor that came with it if that helps.
I figured it out. The tronxy TR sensor is not 5V. I changed the sensor to the Z+ slot, changed the pin to PB14, and changed the the Z+ jumper from 5V to VIN.I can now home all.
Great! Thanks for watching
good evening, I'm getting the TMC error 'stepper_z' reports error: DRV_STATUS: 40190004 s2ga=1(ShortToGND_A!) cs_actual=25 stealth=1, I'm using the tmc2226 drivers, 24v 1.3A 0.9° nema17 motors, I really don't know to do
ya encontre el problema, resulto que el driver del eje z estaba dañado
Me alegro que lo hayas solucionado. ¡Gracias por ver!
@@ChrisRiley gracias a ti por dar una explicación tan detallada hace tiempo que tenia la palca mks skipr pero siempre me daba errores, pero con lo que vi en tus videos me aclaraste muchas cosas excelente serie espero poder ver mas sobre la placa mks skipr
@@pieroandrecastilloarohuanc7705 ¡Más por venir!