Hi Jolene Chad Doug and Nathan. Chad you are going to hear all kinds of comments on what you are doing but my friend you are the only one who has to be satisfied with what you are doing. I say those with comments do things your way and let Chad do it his way. I think Chad and all of them are good at what they do. God bless and have a blessed evening and night
Hey Chad, just a third eye here, you may want to bolt in the trans mount instead of welding just in case you need to pull the trans later. Wouldn’t want to paint yourself into a corner🤔Sorry man, don’t wanna sound like a Monday morning quarterback, just watching your back like you’d watch mine😛Love y’all, love the project
LMAO, Chad finally said, the engine is a tad high? How big is a tab? 1 foot? Chad used the motor mount that were there, his (saving time theory), well look at you now? Wasted time
Chattie will destroy another vintage car , the frame was definitely a drag race frame , unfortunately Chatterbox wouldn’t know this , and the cheaters on the back look OK , question… how can you build anything without using a tape measure, square, etc. , chatty doesn’t know tools , he doesn’t even have a bench in the building, no vice , no nothing! He needs to get busy planting cute little flowers 🌺! FRIGGEN LAMER !!
@@jamesmailly7990Absolutely positively correct!!! He has no clue what the hell he’s doing. You can’t put an engine in with no frame correct or suspension installed. He building this crap ass backwards with no idea what he’s doing.
That trans tunnel is going to sure be high. If they lowered the engine they could run the driveshaft through where it’s built to. Then pinion angle will be correct. Plus wouldn’t have to cut into the frame like that and be less work in the end.
He has no clue what he’s doing. You can’t put an engine in level with no suspension on the vehicle. He doesn’t know nothing about mechanics or building anything correct he just throws crap together.
It looks like the driveshaft originally went through the X in the frame, like the '60s X-frame cars. So maybe the engine should hang on the motor mounts instead of sitting on top? There's quite a bit of clearance below the oil pan.
Where Chad was going to weld on to the frame next to the engine, fish plating would be the way to go the way they have it welded now. It would make it a whole bunch stronger. Just grind it and put the fish plate on the outside then do your work for custom look. You guys do a great job, love watching your videos
Every body needs to stop telling him and let mr perfect learn for him self notice Nate isn’t saying anything so we see the show were he is cutting it apart
Cheap chad would have to spend money he’s probably waiting for someone to send him one I watch a lot of fab shows all of them are adding buildings or buying bigger ones adding new equipment plasma tables I know he added a building but look at it I he added equipment Pullman rusting his lift is bad the metal brake is all rusted nothing of quality cheap chad bad work
If you weld the transmission mount onto the frame as you described, you may not be able to pull the transmission out (or Clutch) without pulling the engine.
It wont matter it’s all being done backwards, he has no clue what he’s doing , if history repeats itself it will never be finished and will be yard art at best. The man has no mechanical ability at all. Engine should been last thing in that frame, he had no suspension, nothing to get the right angles. He did not even prep or paint the frame he blasted, makes absolutely no sense
No one has mentioned the way the front suspension is "mounted." It is not an early 30's Mopar either. Front end looks like a late 40's Ford to me (wider axle then before 1942). Weren't 33 Mopars parallel springs?
So how are you going to take the transmission out? The mount should be bolt in, otherwise your going to have to lift the body off to get the tranz out...
I thought Nate might have spotted it..lets see if he figures it out. There's no way that gearbox is coming out the bottom of the car with that brace in the way
@@funny0000000 That remains a real mystery all in itself!! Probably the same way he got a TV show to film him !! If you notice you never see his son around any more on no videos he makes.. That says pretty much everything.
Did Chad consider having the hot wheels engine forward and fabricating a rearward air intake to give the same look with much less work?too late now but maybe a DOH moment?...you are a fantastic asset to team Chad
So the 40 ford was set aside for Nate to work on and complete. Madd Chad doesn't get bored, he just surpasses what his brain will alow him to complete.
Chad! You can’t have the engine and transmission 1 1/2’ feet ABOVE the rear end. Better let Nate layout the drive train, go get your grinder and cut some fender skirts
He has no clue WTF he’s doing!! No frame finished not even painted, no suspension, no tires right or brakes , and he is try to set the engine on top of everything not down inside the car. Man needs some serious training on mechanical issues.
I’m sure Nate or Doug could operate it. I love the show but don’t understand why he buys new equipment to them but never set it up to use. A new lift for the vehicles would be a great addition.😎🌴
Agreed the best of the bunch by far and she could be better with someone teaching her the correct way of doing it. A good Mig weld on a frame member should be a continuous bead, not one hit at a time as she was instructed to do.
I think just put a floor in it patch a few places and let Jolene race car it, not everything you build has to be chopped or finished to a show car, this is a true hot rod, sometimes simple is better
He has no clue what he’s doing. You can’t set an engine with no suspension in place first the man has no mechanical ability. All the angles will be a complete joke
I say that the motor and transmission looks too high in the current forward frame modification, it's called lower center of gravity apologize for the negative comment.
leave diff welded to chassis to stop suspension windup and loose momentum hopping all over the place. put c cut in for showing..jolene would do this justice drag racin this one
It looks odd as hell but in 4x4s the shafts are worse than that. BUT let’s see were it ends up. Farm tractors have no frame at all. Yurt please don’t cut the shape out of that beautiful body.
This looks like a re-run from the past year let's see rusty old frames greasy motors chop this weld that common jolene talk some sense into chad and build something nice and correct that someone would pay alot of money for being covered in dust every day is cool but let's step it up spend a little money you will get it back same old song is getting old im trying to hang on but it's getting harder and harder to stay loyal.
The screw-ups are the only reason to tune in because you certainly aren't going to learn anything beneficial that would come from Chad's short-circuited brain.
The man gets worse daily!! He has no clue what he’s doing Nobody with half a brain puts an engine in a sand blasted frame with no paint on it no suspension no brakes no proper tires!! He half ass builds everything then never finishes it!! Its a broken record over and over
Prep it all, bring in an actual mechanic.....have it running.....then cut..... Start filming like they it was the first time......such fakery..... Keeping it real my azz.....
Chad just watching you makes me want to work on my stuff your such an inspiration thank you
Yeah Nathan is smart when it comes to cars and getting them going keep up the good work Chad Doug Nathan and Jolene
It will be interesting to see them try to get the correct pinion angle between transmission and differential.
So he can't use u-joints? You keyboard builders are hilarious
Thanx Jolene! My fav type of Bad Chad and Nathan vid! Nice cam work! G B Everyone!
Bolts are suspose to go down on the engine mount ,so if the nut falls off the bolt stays.
Congrats on the views Jolene.. 29k in 21hrs!!!! Your channel is great!!! Cheers, Bernie
Jolene very great job you doing 👏 👍
Flawless, you guys are so impressive, I love this build like all the other obviously!
Hi Jolene Chad Doug and Nathan. Chad you are going to hear all kinds of comments on what you are doing but my friend you are the only one who has to be satisfied with what you are doing. I say those with comments do things your way and let Chad do it his way. I think Chad and all of them are good at what they do. God bless and have a blessed evening and night
lol as a 45 year muscle car restorer i laugh at this joke of a channel ! but as long as you sheep are satisfied with this garbage lol enjoy jr!
Hey Chad, just a third eye here, you may want to bolt in the trans mount instead of welding just in case you need to pull the trans later. Wouldn’t want to paint yourself into a corner🤔Sorry man, don’t wanna sound like a Monday morning quarterback, just watching your back like you’d watch mine😛Love y’all, love the project
Nate is an excellent Mechanic, Bad Chad lucked out bringing Nate into the shop !!!!
You guys are Cooler Than Dang It!
Just curious why you are setting tail shaft of transmission so high. The hole through x member is where tranny usually sits. Hope Chad explains.
That is not the original frame for that body, it has been cut and the front part of the frame has been welded on top of the back of the frame
LMAO, Chad finally said, the engine is a tad high? How big is a tab? 1 foot? Chad used the motor mount that were there, his (saving time theory), well look at you now? Wasted time
Simply because he should give up tools and plant cute little flowers 🌺
Chattie will destroy another vintage car , the frame was definitely a drag race frame , unfortunately Chatterbox wouldn’t know this , and the cheaters on the back look OK , question… how can you build anything without using a tape measure, square, etc. , chatty doesn’t know tools , he doesn’t even have a bench in the building, no vice , no nothing! He needs to get busy planting cute little flowers 🌺! FRIGGEN LAMER !!
@@jamesmailly7990Absolutely positively correct!!! He has no clue what the hell he’s doing. You can’t put an engine in with no frame correct or suspension installed. He building this crap ass backwards with no idea what he’s doing.
Jolene I hope your channel soars ❤️
That's gonna be a great little hotrod
Glad to see Chad use something other than a grinder to cut 😂
That trans tunnel is going to sure be high. If they lowered the engine they could run the driveshaft through where it’s built to. Then pinion angle will be correct. Plus wouldn’t have to cut into the frame like that and be less work in the end.
Good sound on engine good job WIZARD!
You and Nate and Jolene will make it all work 👍👍
You guys are a great team and work on cars to customize them
It's Great the engines running 🏃♂️ The transmission mount should be a piece of cake for a man of your caliber Chad Go for it 👁 🐅 👌
I would love to see this go from nothin to draggin
It still blows me away looking at the flathead V8 exhaust ports. V6 ports on a V8!😁
Looks like a V6 because of the center two.. shear what seems to be one. But it's an 8 ...👍
The centre two ports must be small by looking at the size of the centre pipe!
Siamese center ports.
Ya good vid...i be digin da mo n joe show.flatheads sounds so cool..
I have never had a transmission sit above the frame
Keep in mind just a call from the thirties
@@kennethbrown5814 There is still a tilt to the motor in the 30s
He has no clue what he’s doing. You can’t put an engine in level with no suspension on the vehicle. He doesn’t know nothing about mechanics or building anything correct he just throws crap together.
Half baked orphan cars for sure, this kind of behavior drives guys that know nuts. Remember he's dumb as a fox the money is pouring in as we view.
It looks like the driveshaft originally went through the X in the frame, like the '60s X-frame cars. So maybe the engine should hang on the motor mounts instead of sitting on top? There's quite a bit of clearance below the oil pan.
Where Chad was going to weld on to the frame next to the engine, fish plating would be the way to go the way they have it welded now. It would make it a whole bunch stronger. Just grind it and put the fish plate on the outside then do your work for custom look. You guys do a great job, love watching your videos
The engine is sitting up high
Every body needs to stop telling him and let mr perfect learn for him self notice Nate isn’t saying anything so we see the show were he is cutting it apart
Make sure it has a rotor button lol. Transmission mount should be simple to make.
I agree the engine should be lowered
Great work Chad,Jolene,and Nate! (No Dougels today)
Works of art call in the day thx for watching 😮😜🧐🇨🇦
Chad! Remember you may need to take the transmission mount out to fix / repair the clutch and or transmission!
You know Chad .. there's this machine tool called a bandsaw... They cut real nice and accurate.
Cheap chad would have to spend money he’s probably waiting for someone to send him one I watch a lot of fab shows all of them are adding buildings or buying bigger ones adding new equipment plasma tables I know he added a building but look at it I he added equipment Pullman rusting his lift is bad the metal brake is all rusted nothing of quality cheap chad bad work
If you weld the transmission mount onto the frame as you described, you may not be able to pull the transmission out (or Clutch) without pulling the engine.
It wont matter it’s all being done backwards, he has no clue what he’s doing , if history repeats itself it will never be finished and will be yard art at best. The man has no mechanical ability at all. Engine should been last thing in that frame, he had no suspension, nothing to get the right angles. He did not even prep or paint the frame he blasted, makes absolutely no sense
He will take it all apart
This guy has no skills cheap chad bad work
No one has mentioned the way the front suspension is "mounted." It is not an early 30's Mopar either. Front end looks like a late 40's Ford to me (wider axle then before 1942). Weren't 33 Mopars parallel springs?
33 pd , had springs, pe ,pf had the independent front suspension, but 34 pg had springs
I like the way that engine looks. ❤
my HI again Bad Chad and Jolene from the D Mi 😎 hey thanks for sharing another great video 👍🎉 of what looks like a really cool Build 🎉🤙🔥🤩
The Plymouth is coming along quickly
You are having too much fun Jolee, bring it to Winterport Dragway flathead races. We will be there if you are
Jolene
I think they said she went 50 or 60 mph that’s good cause I wouldn’t go much fast in one of his builds
Great sound
make sure the tilt of trans lets the rear driveshaft bushing get a little oil
Excellent job
Nice job guys
Awesome, Thanks
flat head sounds good!!!
Don’t weld in trans brace or you will have to pull the body off or the front end to get the trans back out
nat got the shocker lol
Aren't engine supposed to have a slight angle at back of engine to stay oiled properly?
Vrooooom...be nice to see this car at pinetree😊
So how are you going to take the transmission out? The mount should be bolt in, otherwise your going to have to lift the body off to get the tranz out...
I thought Nate might have spotted it..lets see if he figures it out. There's no way that gearbox is coming out the bottom of the car with that brace in the way
That’s the least of the problems, he can’t get the angle right with no suspension in place . He has no clue what the hell he’s doing
@@funny0000000 That remains a real mystery all in itself!! Probably the same way he got a TV show to film him !! If you notice you never see his son around any more on no videos he makes.. That says pretty much everything.
Back of trans is to high the floor will need tall drive shaft tunnel
“Little deuce coupe…you don’t know what I got”
You need to point the trans toward the rear end
Great job
Hot rubber nights reminded me of a song that a local band played back in the day here in Detroit
Honeymoon Suite
New girl now
Funny stuff
ruclips.net/video/uK0AmgDGpPo/видео.htmlsi=hS1RM301NfhIDCrD
GREAT JOB NATHAN.....🐓in the🏠 ... MAKE A COMMENT & HIT THAT LIKE BUTTON Enjoy today's SHOW.
Rooster Nathan is the man chads just a two yr old . Wouldnt let him near a ride on mower let alone a car
Looks like the driveshaft is gonna be to high ro line up with the rear end
Yo Rooster! 🎉
@@dennishoward5756....yup.... kind of odd angle due to the silly chop on the front of the frame
Did Chad consider having the hot wheels engine forward and fabricating a rearward air intake to give the same look with much less work?too late now but maybe a DOH moment?...you are a fantastic asset to team Chad
Need to find a set of tires to make it sit level and roll better
So the 40 ford was set aside for Nate to work on and complete. Madd Chad doesn't get bored, he just surpasses what his brain will alow him to complete.
No, he just isn't capable of going any further on the projects.
He has no skill
Chad! You can’t have the engine and transmission 1 1/2’ feet ABOVE the rear end. Better let Nate layout the drive train, go get your grinder and cut some fender skirts
The engine looks to be tilted forward
The driveshaft angle would be way too much as it is with the engine in its current location.
He has no clue WTF he’s doing!! No frame finished not even painted, no suspension, no tires right or brakes , and he is try to set the engine on top of everything not down inside the car. Man needs some serious training on mechanical issues.
It’s going to be funny watch him cut this a part to fix it he has no skills cheap chad bad work
He just makes art . Reason he never drives what he builds. Imagine a accident with the way he mounts bodies on frames (death traps)
Not trying to be smart but there have been many times you could have used the fork lift and it would have been easier for everyone
Looks like none knows how to drive it.
Agreed another level of comedy with the forklift would be an additional improvement to the show !!!
He is scared to run it.
I’m sure Nate or Doug could operate it. I love the show but don’t understand why he buys new equipment to them but never set it up to use. A new lift for the vehicles would be a great addition.😎🌴
I'm thinking Jolene you need to show them how to weld.
Agreed the best of the bunch by far and she could be better with someone teaching her the correct way of doing it. A good Mig weld on a frame member should be a continuous bead, not one hit at a time as she was instructed to do.
You have to joking she can’t weld there idea is 1000 spot weld makes bead I would not trust his welding or teaching skills
Nice 👍
The Trans will need to be mounted
Great job guys gals as usual SWEET JOLENE on the VIDEOS make that cake guys gals
Can you use a plasma cutter without a weld helmet type eye protection?
Sunglasses will work fine
Obviously you can.
the carburetor is not level
I think just put a floor in it patch a few places and let Jolene race car it, not everything you build has to be chopped or finished to a show car, this is a true hot rod, sometimes simple is better
If you simple you have the right guy
eng an trans setting way to high! frount mounts should be inside of the frame juet saying
I dont think he has thought this threw that front frame was stack on top of rear frame that moves engine to high the floor will need big tunnel
He has no clue what he’s doing. You can’t set an engine with no suspension in place first the man has no mechanical ability. All the angles will be a complete joke
I say that the motor and transmission looks too high in the current forward frame modification, it's called lower center of gravity apologize for the negative comment.
Hot Rod - Please
If Nate , and Doug didn’t help Bad Lamer … nothing would ever be done! Example…. The BugsAss hauler ,pile O scrap!!
Jolene are you going to drive this car
You racing this one, Joleen???
Hide the 1in square stock
The show would be over
Crooked is only perspective
If you are going to drag that car put rear mounts on the engine
Nice
how come Chad stopped working on his hot wheels car
Because he has the attention span of a 2 year old
Someone clue bad Barbie he is not building the SPACE SHUTTLE! And teach him how to read a tape measure!!! Pure ROOKIE, at best !!
leave diff welded to chassis to stop suspension windup and loose momentum hopping all over the place. put c cut in for showing..jolene would do this justice drag racin this one
It looks odd as hell but in 4x4s the shafts are worse than that. BUT let’s see were it ends up. Farm tractors have no frame at all. Yurt please don’t cut the shape out of that beautiful body.
Of course it runs, Nate has been messing with it.
Not much wrong with a bonus from Jolene😍
FINA!!!
Nathan should be running the U tube channel he's very smart about cars 🚗 Is bad Chad always so clueless 🙄
Thursday
Hi fina.
She needs tires Chad!
Hello everyone
👌
👍
like 37 !
Rear of motor is way to high lower it down use your brain if you have one left
This looks like a re-run from the past year let's see rusty old frames greasy motors chop this weld that common jolene talk some sense into chad and build something nice and correct that someone would pay alot of money for being covered in dust every day is cool but let's step it up spend a little money you will get it back same old song is getting old im trying to hang on but it's getting harder and harder to stay loyal.
The screw-ups are the only reason to tune in because you certainly aren't going to learn anything beneficial that would come from Chad's short-circuited brain.
The man gets worse daily!! He has no clue what he’s doing Nobody with half a brain puts an engine in a sand blasted frame with no paint on it no suspension no brakes no proper tires!! He half ass builds everything then never finishes it!! Its a broken record over and over
I guess if you can't say anything nice walk away...........
When exposed yourself on social media, expect all kinds of comments, don’t take it personal 😂
And everyone gets a trophy!
No say what feel
If you don't like there channel. Don't watch
💥💥🍻🍔🐿️🌺🛠️
Prep it all, bring in an actual mechanic.....have it running.....then cut.....
Start filming like they it was the first time......such fakery.....
Keeping it real my azz.....