The best video for a double flare on RUclips.I watched over 30 .They don't show you the part about measuring the tube with the side of the adapter. Most showed me to make it the whole length of it, and the filing part is better.I tried 10 times got 1 good flare and broke my crappy Pittsburg tool adapter.
I'm glad to know there is an easier tubing now available for making brake lines. This stuff may have been on the market for a long time, but I just didn't know it. It use to be if you looked and seen a copper brake line on a vehicle, you knew that it had been Jerry Rigged in other places. When making steel lines , I would usually heat the end with a flame to help aneal it between crimps. Always had problems with it splitting the flare without a little heat.
Thanks for the video I've just had my dad's car fail the m.o.t the bra K line burst whilst on the test in england . I was really confused with the double flare but you're a legend i now understand thank you so much you have a new subscriber from Oxford England.
Pretty good video sir. I never even heard of a double flare before. Ive never replaced any brake lines either. I learned how to do flares when i went to community college. I was doing flares on soft copper,im sure its a little different with this material. Thank you.
I never knew brake lines were double flared into I redid them all on a tug and filled the master cylinder up with brake fluid and they all dripped a little because I single flared them all. lol now I know why the double flared means
What if you have to flare the line while it's on the vehicle? such as the line running down from the master cylinder that doesn't need replaced. I guess I would have to remove it from the vehicle to flare it?
I have problems getting the line to stay where I put it in the tool itl slides back & I tightened the bejesus out of it ( steel) line I now use copper nickel line easier to use not easy to do & I pay attention !!
Just redid the lines on my car without a file or deburring tool. It's definitely *possible* to deburr with a knife like I did but uh...this way looks easier
The best video for a double flare on RUclips.I watched over 30 .They don't show you the part about measuring the tube with the side of the adapter. Most showed me to make it the whole length of it, and the filing part is better.I tried 10 times got 1 good flare and broke my crappy Pittsburg tool adapter.
Thanks glad I could help!
The new "in-car" double flare tools are a game changer (Capri). Smaller tool, self centering die insert, & perfect flares everytime.
I'm glad to know there is an easier tubing now available for making brake lines. This stuff may have been on the market for a long time, but I just didn't know it. It use to be if you looked and seen a copper brake line on a vehicle, you knew that it had been Jerry Rigged in other places.
When making steel lines , I would usually heat the end with a flame to help aneal it between crimps. Always had problems with it splitting the flare without a little heat.
Very influential brother 👍
Thanks for the video I've just had my dad's car fail the m.o.t the bra K line burst whilst on the test in england . I was really confused with the double flare but you're a legend i now understand thank you so much you have a new subscriber from Oxford England.
Glad I could help!
if I had a dollar for every time I forgot to put the nut on first......
LOL
Simple to the point and it works ,thank you.
Ready to do mine on my C10 now. Thank you man!
Pretty good video sir. I never even heard of a double flare before. Ive never replaced any brake lines either. I learned how to do flares when i went to community college. I was doing flares on soft copper,im sure its a little different with this material. Thank you.
Great easy to follow video, and explanation is spot on. Thank you 👍
Thank you, I’ve never done a double flare before
You’re welcome 😊
I look at double flare as making a "crush washer" fitting to seal better
I never knew brake lines were double flared into I redid them all on a tug and filled the master cylinder up with brake fluid and they all dripped a little because I single flared them all. lol now I know why the double flared means
Great job man
Exellent clear and really well videoed,sir,thankyou loads,ste from the uk😊
hey that was informative! just what I needed! but you mispelled watching at the end
And that is why you will find me in the shop most of the time. LOL
thanks for the deburring tip
Did not know about file trick or brake fluid lube trick. I’m doing SS lines
Thankyou
Thanks. Great video very helpful.
Glad it was helpful!
Thanks for the great job very simple and easy appreciations 🇩🇰🤣👌👍
what happens if your "anvil"/die doesn't have a measuring mark?
Thanks for sharing.
Our pleasure!
Just found your channel and Subscribed. Very nice video
excellent video ....
Great video, thanks 👍
Thanks
What if you have to flare the line while it's on the vehicle? such as the line running down from the master cylinder that doesn't need replaced. I guess I would have to remove it from the vehicle to flare it?
No you can take the tools to the car. I put it in the vise so it would be easier to video.
I have problems getting the line to stay where I put it in the tool itl slides back & I tightened the bejesus out of it ( steel) line I now use copper nickel line easier to use not easy to do & I pay attention !!
I bought some copper nickel (so they say) 1/4" tubing off of Ebay. How can I be sure it is Nicopp tubing?
Just redid the lines on my car without a file or deburring tool. It's definitely *possible* to deburr with a knife like I did but uh...this way looks easier
Tqvm....
Awsome😊😊
How you supposed to do this underneath the car.
I thought these were called "bubble" flare?
👍👍
4:20
Its not an anvil, it's called a die.
Thats not what your mom said
WTH hell is a single flare for anyway? never used one
lol low-pressure lines
Literally the worst how to video I have ever seen. 😂
Damn, where’s your video?