DK - if you add 2 small bolts with hex heads to the inner surface of the fence runner (the bit that runs along the edge of the table) at each end where the toggle clams are, you'll then be able to "tune in" the fence to be PERFECTLY 90 deg to the TABLE, by adjusting the bolts forwards or backwards - there are various ways to do this, but the most simple would be to draw a pencil line on the table along the fence, then flip the fence to the other side of the table and see how it lines up, a discrepancy will be obvious (it's the same trick as checking a carpenters square for "square". Once you've got the fence to a perfect 90 deg to the TABLE, then you can also fine tune the blade to the fence by just slightly enlarging the screw holes holding the saw frame to the table and making tiny adjustments until tha saw blade is perfectly aligned ot the fence. This is standard practice for setting up a table saw - having a misaligned blade or fence will cause unlimited poroblems until it's correctly set and aligned to each other. I realise this advice is 2.5 years late, but just in case anyone else see's your idea and uses it.
This is most simple way to make table saw I have ever seen, even I am as a beginner in woodworking will be able to make my own table saw. Thank You so much about your usefull video God Bless You👍🙏
The simplicity and the effectiveness of this method is extremely well. If I can only bring one knowledge of building a table saw, this is the one I'll pick.
몇개월전부터 유튜브 가끔 보고 있습니다. 정말 대단하십니다. 그래서 처음부터 하나씩 따라해 볼려고 첫번째 동영상을 보았습니다. 아래 댓글을 보니 이때(지금으로부터 약 1년전)가 초보라고 쓰셨는데 이걸 보고 더 깜짝 놀랐습니다. 아무튼 대단하시고 참으로 창의적이십니다. 앞으로도 좋은 동영상 많이 부탁드립니다. 그리고 원래 하시는 일이 궁금해지네요. ^^
Thank you for this video. I’m working on a homemade router table, and I’ve been trying to figure out how I’m going to do the fence. I’m going to do something really similar to what you did here. You’re awesome!
A very well thought out diy table saw. Nice and simple is sometimes the best approach. I agree with another comment that you ideally need to add dust collection which I think you can easily achieve. You clearly didn’t intend to build a very complicated table saw so I don’t necessarily agree with the comment that “there is a lot of room for improvement “ especially as I feel you are more than capable if that is what you had set out to do. However if I may make as observation which is safety related. You are currently not protected against kick backs so you might want to consider installing a riving knife and maybe a simple blade guard. Otherwise a really nice neat low cost table saw. I especially like your approach to the fence. 👍
@ Steve 127 Your 2 suggestions sound straightforward, but in fact are quite complex tasks to achieve on this simple arrangement. ● Do you have any suggestions at all as to how they might be achieved? Looking forward to your in-depth response 🤔
Great work. This is as basic as it gets to a simple DIY table-saw that really can be accomplished w/o having drill press, friggin' blowtorch and other big-ass equipment, unlike other "DIY table-saw using SIMPLE tools" videos...
I was impressed about then fence system, simple and ingenious. Would have never thought of the clamps like that .. I need a new fence for my table saw ... this could be a winner
Awesome creation... keep always creative 👍 By the way, I think your table need to adjust higher to meet a comfort stand, you seem always bend your body
Simple and effective. Good to have a very smooth surface for the wood to slide. Greatest concern is that there's no riving knife. For anyone not familiar with table saws and new to them, I strongly recommend you understand what "kickback" is and how the riving knife will stop this from happening. Without the riving knife you will 1) What to make sure your guard opens up away from the blade a small amount 2) Use a push stick to push would through closer to the blade One pro of no riving knife is that you could use the table saw to make crown molding by cutting on a 45 and adjusting the blade up 1/8th of an inch each time.
Before anyone decides to make this from this video, I highly suggest watching some table saw kickback videos. I noticed the board was twitching side to side when you were beginning to feed the board. You are not supposed to push the off piece. It's simple design many people choose not to make for good reason. Table saw is the most dangerous tool in the shop.
Is make a circular saw to be table saw with just screw is not safe for long term using? I see a lot of video of it and decide to buy a real table saw with little range of price.. it have better safety i think
Very nice. Very pretty, and the fence clamps particularly are really cool. You really should have some kind of a riving knife, though - even if it's just a piece of aluminum angle. I'm not an expert, but my understanding is that a riving knife is the #1 line of defense against kickback.
If you want a table saw, buy a table saw...as someone who uses one all the time, this is friggin scary! The chance of a serious kickback is almost 100%
Parts list? Like those table clamps? Type of wood or if you put a finish or oil on the woood to make it slide better and where you get the tracks the clamps slide on? Thanks and I love all your videos, you’re so talented and make everything a lot more learnable unlike most videos, you create amazing work with basic power tools...it shows your true skill and proves you can build anything as long as you use your creativity
초보/입문 취목하시는 분들 중에서 혹시 정말 테이블쏘를 제작해서 사용하실 생각이 있으시다면 킥백 예방 정말 신경 많이 쓰셔야 합니다 사제 테이블쏘는 조기대와 톱날의 수평이 항상 완벽하게 수평이될 수 없기 때문에 절단 길이가 길면 길수록 톱날에 가해지는 수평압력의 차이가 발생하게 됩니다 그 압력이 쌓이면 사고로 이어지니 명심하고 예방하시기 당부드립니다ㅠㅠ
음... 저도 킥백을 포함한 다른 문제들이 너무 걱정되네요. 자막이나 제목에 초급자가 이렇게 만들어쓰면 다칠수 있다는 문구를 넣으셨으면합니다. 그리고 두손 핸들링이 필요한 커팅기들은 긴급전원차단 장치(이머전시 스탑)가 있거나 켜고끄는 장치를 무릎 등으로 할수 있어야 되는게 요즘 추세입니다. 첫댓글에 테클만 써서 죄송합니다. 다치는 분들이 없길 바랍니다.
Simple and effective,now all it needs is a dust collector!
ZXCharlieR the first cut at the end made me laugh with that big ol sawdust cloud 😁
ruclips.net/video/A8NHKI3YTgw/видео.html
@@moroccandiycreators5966 ?
@@intell0 hi you can see my channel just started, you can also subscribe
where would we need that for? i have perfectly functioning nose and lungs
깔끔해서 군더더기가 없고 완성도가 높은 훌륭한 솜씨 입니다.
감사합니다 ^^
DK - if you add 2 small bolts with hex heads to the inner surface of the fence runner (the bit that runs along the edge of the table) at each end where the toggle clams are, you'll then be able to "tune in" the fence to be PERFECTLY 90 deg to the TABLE, by adjusting the bolts forwards or backwards - there are various ways to do this, but the most simple would be to draw a pencil line on the table along the fence, then flip the fence to the other side of the table and see how it lines up, a discrepancy will be obvious (it's the same trick as checking a carpenters square for "square". Once you've got the fence to a perfect 90 deg to the TABLE, then you can also fine tune the blade to the fence by just slightly enlarging the screw holes holding the saw frame to the table and making tiny adjustments until tha saw blade is perfectly aligned ot the fence. This is standard practice for setting up a table saw - having a misaligned blade or fence will cause unlimited poroblems until it's correctly set and aligned to each other.
I realise this advice is 2.5 years late, but just in case anyone else see's your idea and uses it.
This is most simple way to make table saw I have ever seen, even I am as a beginner in woodworking will be able to make my own table saw. Thank You so much about your usefull video God Bless You👍🙏
Don't do it! Buy a proper table saw...I really like this channel, but this is a really really bad idea.
외국꺼만보다가 한국에도 이런분이 있다는게 좋네요 구독 박고 잘보겠습니다
오랜만에 보는 한글 ㅠ 감사합니다~~
The simplicity and the effectiveness of this method is extremely well. If I can only bring one knowledge of building a table saw, this is the one I'll pick.
Супер просто дешево и технологично. Всегда можно использовать ручную пилу в других целях. 👍👍 👍 👍 👍
진정한 능력자시네요~언제나 즐거운 목공하세요~^^
감사합니다~~ ^^
Very good 👍
Thank you 👍👍
So simple and so effective! 👌👌
몇개월전부터 유튜브 가끔 보고 있습니다. 정말 대단하십니다. 그래서 처음부터 하나씩 따라해 볼려고 첫번째 동영상을 보았습니다. 아래 댓글을 보니 이때(지금으로부터 약 1년전)가 초보라고 쓰셨는데 이걸 보고 더 깜짝 놀랐습니다. 아무튼 대단하시고 참으로 창의적이십니다. 앞으로도 좋은 동영상 많이 부탁드립니다. 그리고 원래 하시는 일이 궁금해지네요. ^^
안녕하세요~ 댓글 감사합니다.
저는 건죽 설계일을 12년 했고 목공은 이번에 처음이예요 잘 부탁 드립니다^^
I need one of these for small jobs so I don't have to take out my big table saw. Great job.
Mantap kawan sukses selalu buat mu ok abis itu aku suka sekali cara mu buat nya.
This is the simplest and most effective idea so far l seen on the RUclips. Well done dude.👍
Thanks for kind words :D
Nice job! Suggestion: add a ruler to the table top's edge and a marking on the fence's "guide" for reference.
ruclips.net/video/A8NHKI3YTgw/видео.html
베큠 연결 하면 먼지뒤집어 쓰지 않을텐데요. 일반테이블에 간단히 테이블쏘 만드는것 잘 봤읍니다.Thank you! Good Idea!
분진 엄청 심해서 최근 영상에 만들었어요 시청해주셔서 감사해요 ~
Good job brother 👍👍
Thank you for your support bro~ :)
@@dekayscrafts greetings creator content
Thank you for this video. I’m working on a homemade router table, and I’ve been trying to figure out how I’m going to do the fence. I’m going to do something really similar to what you did here. You’re awesome!
A very well thought out diy table saw. Nice and simple is sometimes the best approach. I agree with another comment that you ideally need to add dust collection which I think you can easily achieve.
You clearly didn’t intend to build a very complicated table saw so I don’t necessarily agree with the comment that “there is a lot of room for improvement “ especially as I feel you are more than capable if that is what you had set out to do. However if I may make as observation which is safety related. You are currently not protected against kick backs so you might want to consider installing a riving knife and maybe a simple blade guard.
Otherwise a really nice neat low cost table saw. I especially like your approach to the fence. 👍
@ Steve 127
Your 2 suggestions sound straightforward, but in fact are quite complex tasks to achieve on this simple arrangement.
● Do you have any suggestions at all as to how they might be achieved?
Looking forward to your in-depth response 🤔
Thnx. Just what i was wanting but couldnt work ot out 😁 so simple.
Great work. This is as basic as it gets to a simple DIY table-saw that really can be accomplished w/o having drill press, friggin' blowtorch and other big-ass equipment, unlike other "DIY table-saw using SIMPLE tools" videos...
초보분들께서는 영상은 참고용이 좋을듯합니다~ 수평이 조금만 틀어져도 킥백 발생할수 있습니다~ 첫째도 안전 둘째도 안전 다들 안전하고 즐거운 목공되세요~ 잘보고가요 김팀장님~!!
좋은 말씀 감사합니다 ^^
태어날때부터 천재시네 ㅋ
Excellent. Love the fence. Great job.
Good seeing one that’s not unnecessarily over engineered..
I was impressed about then fence system, simple and ingenious. Would have never thought of the clamps like that .. I need a new fence for my table saw ... this could be a winner
Thank you so much =)
What do you call the special clamp
I'm interested at clamp, where I can buy?
Toggle clamps 😁
Thanks 4 tutorial, good idea👍👍👍👍
Amazing. Great job. The only thing I would suggest is putting a little wax on the sliders to keep them moving freely.
Good idea Thanks =)
Awesome creation... keep always creative 👍
By the way, I think your table need to adjust higher to meet a comfort stand, you seem always bend your body
Thank you so much for this video^^♥♥♥
This is the best and the most simple one i have ever seen so far!!! Thanks♥♥♥♥♥
Simple and effective. Good to have a very smooth surface for the wood to slide.
Greatest concern is that there's no riving knife. For anyone not familiar with table saws and new to them, I strongly recommend you understand what "kickback" is and how the riving knife will stop this from happening.
Without the riving knife you will
1) What to make sure your guard opens up away from the blade a small amount
2) Use a push stick to push would through closer to the blade
One pro of no riving knife is that you could use the table saw to make crown molding by cutting on a 45 and adjusting the blade up 1/8th of an inch each time.
Thanks for sharing! Easy to build and it works! Great idea with the toggle-clamps; I've never seen it this way before!
Thanks =)
ruclips.net/video/A8NHKI3YTgw/видео.html
와 이거 너무 훌륭합니다-! 따라 해보고 싶어요~!
Nice work. I would add a T-Track on each side for "feather boards" to prevent kick back and possibly a miter gauge and / or cutoff sled
I definitely won't use any MDF again indoors! :D I just can't stand the dusts. Nice DIY table saw by the way!
Before anyone decides to make this from this video, I highly suggest watching some table saw kickback videos.
I noticed the board was twitching side to side when you were beginning to feed the board. You are not supposed to push the off piece. It's simple design many people choose not to make for good reason. Table saw is the most dangerous tool in the shop.
That's right. Thanks for the good comments. =)
Nope, uneducated and inexperienced are the most dangerous
yeah i noticed that he put the fence on reverse.
Is make a circular saw to be table saw with just screw is not safe for long term using? I see a lot of video of it and decide to buy a real table saw with little range of price.. it have better safety i think
Very straight forward and practical👍
Very nice. Very pretty, and the fence clamps particularly are really cool. You really should have some kind of a riving knife, though - even if it's just a piece of aluminum angle. I'm not an expert, but my understanding is that a riving knife is the #1 line of defense against kickback.
Muy buena idea. Saludos desde Argentina 🇦🇷
Good job. Congratulations!.. Thank you
It's really very good. Is coming fast. At 10 days only.
Tnxs very much bangood
전문가의 손길이 느껴집니다.
굿
Good
감사합니다 ^^
nice, simple, user friendly DIY table saw and fence, I've seen many other clips which are complicated and not easy to make.....
깔끔한 화면 구성과 멋진 작품.....대단하십니다
감사합니다^^
If you want a table saw, buy a table saw...as someone who uses one all the time, this is friggin scary! The chance of a serious kickback is almost 100%
늘 유익하게 보고있어요~^^
사용한 토글클램프 사이즈가 궁금합니다
설매지그 만들때 사용한 토글클램프 사이즈도 사이즈가 궁금합니다
몇kg짜리 인지요?
여기가 그...훼사원님이 연예인같고 유명하시다던 김팀장님 유튜브인가요 ㅋㅋㅋㅋ
Gives me a nice idea when i want to make my own..nice tutorial video for me..thanks.
Хорошая идея. Только по технике безопасности работать с вращающимися механизмами лучше без перчаток. Good idea
Я больше не ношу перчатки
Спасибо большое )))
Nice build. I enjoyed the video. I wouldn't do it myself, but I appreciate the ingenuity.
Thank you :)
목공에 관심이 많아서 구독하게 되었습니다
똑같이 만들어 보고싶은대
부자재가 무엇들인지 궁굼하네요
첨 시작하는거라 목공에 필요한부분도
알고싶네요 시간되실때 조언부탁드립니다^^
mudah membuatnya dan sangat simple.. semoga canel indonesia bisa buat se simple ini, yang gak bertele2 😎👍
Great project, but raise your table it's way too low. Dust collection could be your next project. Thanks for sharing from Mexico
Very nice ! But only one bad point ... how you managed with all the flying dust ? Thxs
Unique clamping system... Simple and bloody brilliant!
Super thank you =)
Parts list? Like those table clamps? Type of wood or if you put a finish or oil on the woood to make it slide better and where you get the tracks the clamps slide on? Thanks and I love all your videos, you’re so talented and make everything a lot more learnable unlike most videos, you create amazing work with basic power tools...it shows your true skill and proves you can build anything as long as you use your creativity
Going to make it , it looks easy to make .
좋은 영상 감사합니다.
트랙 고정해주는 클램프 자재 명칭이 무엇인지 알고 싶습니다.
구독자 팬 입니다.
토글 클램프 입니다😁
Good job 👍
Teu trabalho ficou simples e efetivo, faça uma caixa em volta da serra com encaixe para aspirador de pó, só isso para ficar 100%, abraços do Brazil
Very practic end simple 👍
Thank you =)
플로우님 영상 보다 들러봅니다. 한국분들도 많으시지만 외국분들도 시청을 많이 하시네요. ㅎㅎ 좋은 영상 잘 보고 갑니다. 감사합니다 😊
안녕하세요~
주제가 목공DIY이다보니 해외에서도 보시는것 같아요
들러주셔서 감사합니다^^
나이들면 고생해요 무릎 보호대. 안전화 필수. 잘 보고갑니다.
네 알겠습니다. 말씀 감사합니다. ^^
Very well made, but it's too dangerous to mount the manual saw upside down, there is no protection over the blade, and it could produce kick-back
It’s obvious that too many people don’t care or are oblivious to what can happen to them!
Excellent! And one heck of a lot cheaper than the $650 I was ready to spend .......
Super helpful, al it needs is a vacuum and youbare set! 👍 thank you
잘봤습니다
집진기능 추가되면 좋겠네요
들러주셔서 감사합니다~
집진기 부품도 중국에서 건너오고 있어요
준비 되는대로 올리겠습니다~~
초보/입문 취목하시는 분들 중에서
혹시 정말 테이블쏘를 제작해서 사용하실 생각이 있으시다면
킥백 예방 정말 신경 많이 쓰셔야 합니다
사제 테이블쏘는 조기대와 톱날의 수평이 항상 완벽하게 수평이될 수 없기 때문에
절단 길이가 길면 길수록 톱날에 가해지는 수평압력의 차이가 발생하게 됩니다
그 압력이 쌓이면 사고로 이어지니 명심하고 예방하시기 당부드립니다ㅠㅠ
좋은 말씀 감사합니다. 말씀하신 부분 항상 염두하고 작업하겠습니다~
넵 설명 감사합니다
이해가 잘 안되는데 좀더 설명을 해주실 수가 있을까요? 톱날이 부러져서 튄다는 말씀인가요? 킥백이라는게..
@@freedom_is_notfree 판제가 뒤로 밀린다는거에요..각도가 안맞으니 ..앞이 넓으면 상관엄지만 앞이 좁으면 나타나는 현상.....
지그 지존이 많은지 처음 알았어요...대단한불 진짜 많으시네요
Muy facil y practico video , Buen trabajo !!!
I've watched this video for almost 5 times. Nice video for my imagination.
토마스과학실험ThomasScience sasayaminntakfilampooroohsayamintafilamponoosayamintskys
토마스과학실험ThomasScience ssayamintaklaguarickite
the best is the baggie of glue.
썰매지그도 제작하심 ...작은거 자를때는 킥백도 피하고 좋아요
안녕하세요 만물상회님~
썰매 만들려고 준비중인데
몇가지 방법을 두고 고민중이었어요
곧 영상 만들어서 올려보겠습니다~~
Complimenti bellissima idea 👍👍👍👍👍👍👍
E 'bello vederti. Grazie Incontra spesso :)
Genial amigo es muy proyecto muy práctico y sencillo me gusto un saludo tu amigo 1417 😁👍
Gracias por tu alabanza. :)
great video. thanks for sharing
김팀장님 궁금한게 있는데요.
원형톱 트리거랑 날높이 고정은 어떻게 하신건가요?
트리거는 케이블타이로 묶어놓고 멀티탭에서 온오프 하고, 날 높이는 책상 밑으로 내려가서 원형톱 높이 조절 기능을 이용합니다. =)
지금까지 봤던거중에 가장 간단하군요
감사합니다 ^^
이렇게 제작해서 팔기도 하나요?
well done man 👍🏻👍🏻
Thank you ~👍🏻👍🏻 :)
너무 대단합니다. 목공에 관심이 있어 질문드려보는데요. 혹시 초보입문때 김팀장님 스타일처럼 배워보고싶은데 내장목수쪽이나 공방목수 어떤걸 배워야할까요? 전업은 아니고 취미생활로 완벽하게 시간좀 녹여볼생각입니다 :)
muito bom excelente trabalho que Deus te abençoe pôr essa dica porquê tem gente que sabe fazer as coisas e não mostra nem ensina a ninguém.
Verdade viu Luis
Very nice, unique, simple design. Great job!
Thank you :-)
음... 저도 킥백을 포함한 다른 문제들이 너무 걱정되네요. 자막이나 제목에 초급자가 이렇게 만들어쓰면 다칠수 있다는 문구를 넣으셨으면합니다.
그리고 두손 핸들링이 필요한 커팅기들은 긴급전원차단 장치(이머전시 스탑)가 있거나 켜고끄는 장치를 무릎 등으로 할수 있어야 되는게 요즘 추세입니다.
첫댓글에 테클만 써서 죄송합니다. 다치는 분들이 없길 바랍니다.
의미있는 좋은말씀 감사합니다~
전원장치와 추가 옵션을 차차 적용하려 계획 중입니다~
테이블크기가작은것만효과좀있는것같아요.큰테이블은지그를처음에직각으로만들어도변수가생기면틀러져서이동도잘않되고직각으로않잘림.
이보다도양쪽레일을 사용하시면더좋을듯
조기대 부분에 수평을 미세하게 맞출수잇는 방법이 있었더라면 좋앗을듯 하네요
아무리 정교하게 맞춰도 1mm 이하의 오차까진 맞추기 힘드니까요(나무가 영원히 변형이 없는건 아니니까요)
Fantastic! Just gonne copy that! Thanks!
Thank you =)
Good jobb 🇮🇩🇮🇩🙏🏻🙏🏻
고정철물 이름이 뭔가요?알아야 살수 있을것같아서요.
토글 클램프 검색하시면 나와요❤️
Very nice! So simple and practical. Thank you for the video!
Thanks for these ideas
Thanks =)
Excelente idea, buen trabajo, sencillo y muy útil. Saludos
안녕하세요 ''''
일전에테이블쏘 자작시 45도이동위치 에대한질문자입니다''''
의견주신베벨각도감사합니다''
주신의견에공부하여''''
드디어오늘 45도이동완성하였읍니다'''''''
아 By Ch님 완성하셨어요?
제가 조금이라도 도움 되었다니 저도 기쁘네요
축하드립니다~~
멋지네요 좋은 정보 고맙습니다
Good Idea. I would put bearings on the other side to stop the rocking.
Excelente idea, gracias por compartir
2분40분쯤에 보이는2개의 고정장치를 어디서 구하는지 궁금합니다.
선생님 테이블잡는 빨간 손잡이 그거 이름이 모에요? 어디서 사야해요?
토글 클램프 라고 검색하시면 돼요~
안녕하세요~~~
고정철물 명칭이 뭔가요?
토글클램프 입니다~
@@dekayscrafts 감사합니다