Great video, need to do this to mine just have to find the parts car. Can't believe how calm and chill you are in those tight spaces. Obviously a ton of experience. Thanks again man.
I was cringing the entire time. Jacks aren't designed to hold weight over a period of time, only to lift. That's what jack stands are for. Other than that, super helpful. Thanks for posting.
That was very helpful to get the right fender off. Thanks., but when you get to the left fender the windshield washer reservoir is in the fender blocking access to those last 2 screws in the door jamb. Any hints on how to get that reservoir out of there. I already removed the two visible screws?
Hey nap town happy 4th. I was always curious as to why these models have to be jacked up so high in the air before the tires actually come off the ground. Is it a failing part.
Always clean ALL the dirt and debris from the body working areas..dirt can easily cause bolt or screw cross threading and or stripping out..where there was factory weather caulking.. clean that away and apply fresh material.. sealant was applied there for a reason the QC saw in testing.. Black plastic Push pin clips are what is used in much of the plastic fender and splash guard areas in Nipponese mfg autos, it breaks away under less stress than the part it holds so it helps prevent rips and tears in plastic panels and similar parts as well..
What about the 2 T30's Behind the Fender Seal and the Plastic Pop Rivets That like Ya Know,,Actualy PUT the Fender Seal Back in Place?? Did this tonighy on My S5 on Drivers Side With the Water Bottle. What a Bitch to put it Back 100% Factory!! New Fender I Had to Rivet All the Mounts In that I had to Drill Out of the Old Fender. If it Wasnt A Perfect Condition 2012 S5 "Special Edition" I Would Push this Damn Car into a Lake🤟
Road salt have toasted my fenders and your video have given me inspiration to replacing them this summer. Thanks a lot from Norway.
Just wanna say thank you for these helpful videos. I've saved $$$$$ watching them and working on my Audi in my driveway... THANKS!!!!!!!
Great video, need to do this to mine just have to find the parts car. Can't believe how calm and chill you are in those tight spaces. Obviously a ton of experience. Thanks again man.
Great video, you’re very clear and easy to follow, thanks for sharing this. I like your leaf trick too! 👍
About to do this exact project. Thanks for the thorough tutorial man!
How'd it go??
The leaf trick is nice in a pinch! I usually use paper from a receipt.
Don't want to see you hurt, throw you a tire under that thing or a jackstand.
Thanks for all the content.
I was cringing the entire time. Jacks aren't designed to hold weight over a period of time, only to lift. That's what jack stands are for. Other than that, super helpful. Thanks for posting.
Fairly straightforward,I know now what the job is worth!
Do you buy pre painted parts? Have a site you buy from? Thanks!
Thank you for all you do for us brother 🤛
That was very helpful to get the right fender off. Thanks., but when you get to the left fender the windshield washer reservoir is in the fender blocking access to those last 2 screws in the door jamb. Any hints on how to get that reservoir out of there. I already removed the two visible screws?
you can just pull it out by pushing it towards the fender and towards yourself at the same time so it gets un-caught by the filling tube.
Any thoughts on getting that windshield washer reservoir removed on the driver side
Hey nap town happy 4th. I was always curious as to why these models have to be jacked up so high in the air before the tires actually come off the ground. Is it a failing part.
If you put a performance clutch on a 6 speed manual trans in a 2011 Audi A4 will this allow the trans to handle more torque?
I just did the drivers side
More of a pain as you have to remove the washer reservoir
What are all the bolt and screws size needed to remove?
Always clean ALL the dirt and debris from the body working areas..dirt can easily cause bolt or screw cross threading and or stripping out..where there was factory weather caulking.. clean that away and apply fresh material.. sealant was applied there for a reason the QC saw in testing.. Black plastic Push pin clips are what is used in much of the plastic fender and splash guard areas in Nipponese mfg autos, it breaks away under less stress than the part it holds so it helps prevent rips and tears in plastic panels and similar parts as well..
Where you get those clips for the fender line the first one you where putting
Hello naptown tuner. Live your channel. I have a question. Is the 4.2 litre V8 Volkswagen from a Toureg a good engine? Thanks for all you videos
Your a savage love your videos keep it up
Great video man, At the end of the video where you fixed the gap, Did you you just tighten the top screws? How did you do it?
I think he just shifted the positioning of the top screws by pushing them in
Loosen the top screws, push the fender in by hand and start tightening the screws back up as you go along.
Will this work for an Audi A5?
Do a vid on replacing heater/airconditiong flap motor mine center console ones are bad and I wanna see one done before I do it.
where did you order the fender at, and about how much was it?
Did you find one?
Will B9 be similar to this?
Hey brother, I have been having some weird rough starts. Misfires occurring for the first 5 seconds of warm up. Are my coil packs and plugs bad?
Is that a red s4 in the back ?
Hey man is the belly pan still available?
Awesome video, man! Really helpful! :)
Another good vid.
Could you give the specs on those Koni shocks?
Any short blocks for sale ?? 2011 audi A5 2.0t???🧐
Great video
2012 not in the title, different process or just typo?
B8 = 2008-2012 for Audi
Can you do a video on how to buy tires? I’ve heard the new Michelin AS4 are really good, but there like $1k. How do you buy tires?
Hey a little off topic but does anyone know how much hp a 2011 A4 transmission can reliably handle?
8 speed auto b8.5 either 400/500tq. Manual b8 360 tq. If you have 6 speed probably around 350tq.
@@vagcentral2252 thank you much appreciated
Hi this is Erin Cascade Maryland I like to see how you change a fuel pump B7 A4 Audi 2.0
You from Annapolis?
Do you think someone would survive with a huge confederate flag on a huge flag pole in front of their house in Annapolis?!
Yes KONI shocks 👍🏼
Best🎉
U still have the parts car
What about the 2 T30's Behind the Fender Seal and the Plastic Pop Rivets That like Ya Know,,Actualy PUT the Fender Seal Back in Place?? Did this tonighy on My S5 on Drivers Side With the Water Bottle. What a Bitch to put it Back 100% Factory!! New Fender I Had to Rivet All the Mounts In that I had to Drill Out of the Old Fender. If it Wasnt A Perfect Condition 2012 S5 "Special Edition" I Would Push this Damn Car into a Lake🤟
Just needed to remove the filler neck, then it came right out.
Bumper emblem