Im trying to learn how to tint i basically got it down but had a few problems with tucking the film in the seals but after watching this video i was impressed with your tutorial you showed and explained everything thoroughly. I ve watched several different tinters over tha past couple of weeks and i finally found what im looking for. Im hoping you have videos on the tools is it necessary to have the exact tools ? I have a heaf gun like yours but what you called a bulldozer i dont have. I purchased some plastic cards like you used and bought a couple squeggies but the proper tools is maybe one of my problems. The other not removing the door panels a huge help and difference thanks for your help. Also where can you buy the proper tools for installation?
I have a suggestion that should fix some problems I see with your style of tinting. Go to Harbor Freight and get the plastic jar of small bungee cords to hang your door panels. I can tell you know what you’re doing but heating a finger on the inside with the panel that close is dangerous. A newbie could be out a very expensive door panel. Or you could just shrink the pattern before install. Love your show.
Oh my God dude ! You took no precautions to protect that leather interior . I would never have you do this work to my car just because it’s soapy water does not mean it won’t stain the leather.
Hey dude I bought a 53 workhorse for my precuts but since I set it up it has had giving me trouble ,I have adjust the knife , I have adjusted the pressure and never cut perfect i always gotta go trough the cuts with my hand ,it leave some film stick to it it doesn’t cut trough the liner perfectly and if i put a lot of pressure it cut trough all any recommendation? I’m using carbon film , Would it help me a lot thank you !!!
When you done all that you should remove windows . It take about 10min more. For removing just gasket you can pull out uper part of panels. No need to remove it.
Yeah all respect for going the extra mile but why? Is it a way to charge more? Without the panel I get one micro creases on one side and they’re gone in 30 seconds with heat
when 2 staging sometimes you will get creases on the sides and have to chizel out. removing panels or sweeps you get a much easier and cleaner install because you can just drop the bottom of the film behind the panel with no obstruction
I just had too much soap in the bottle.. letting it sit may actually allow the film to collect contamination or fall too low grabbing contaminates from the bottom of the glass.
Thank you so much sir for teach me I always watch your video actually I am denter but also doing detailing work so Any vacancy available there
Just tinted an M5, and this video helped a ton with popping the panels
thorough job ! I have a 2019 bmw 540 , how much for this service with 5% ceramic tint ?
You should definitely make a “ spray squeegee spray “ t-shirt 😂👍🏼
🤔🤣
id buy it 100%
Im trying to learn how to tint i basically got it down but had a few problems with tucking the film in the seals but after watching this video i was impressed with your tutorial you showed and explained everything thoroughly. I ve watched several different tinters over tha past couple of weeks and i finally found what im looking for. Im hoping you have videos on the tools is it necessary to have the exact tools ? I have a heaf gun like yours but what you called a bulldozer i dont have. I purchased some plastic cards like you used and bought a couple squeggies but the proper tools is maybe one of my problems. The other not removing the door panels a huge help and difference thanks for your help. Also where can you buy the proper tools for installation?
DO you watch videos or get the info from somewhere on how to remove door panels for the vehicles you are tinting?
Great video! Very easy to understand and very well spoken!
I wish I could work with you 🙂you do great work ☺ There is something to learn from every video of yours........
I have a suggestion that should fix some problems I see with your style of tinting. Go to Harbor Freight and get the plastic jar of small bungee cords to hang your door panels. I can tell you know what you’re doing but heating a finger on the inside with the panel that close is dangerous. A newbie could be out a very expensive door panel. Or you could just shrink the pattern before install. Love your show.
doors pads can be protected from water spraying by covering it with plastic sheets.
Oh my God dude ! You took no precautions to protect that leather interior . I would never have you do this work to my car just because it’s soapy water does not mean it won’t stain the leather.
thanks for watching :)
Not real leather, only the newer 7 series
Hey dude I bought a 53 workhorse for my precuts but since I set it up it has had giving me trouble ,I have adjust the knife , I have adjusted the pressure and never cut perfect i always gotta go trough the cuts with my hand ,it leave some film stick to it it doesn’t cut trough the liner perfectly and if i put a lot of pressure it cut trough all any recommendation? I’m using carbon film , Would it help me a lot thank you !!!
Great movie. Good to see how to do it.
Why dont You use bottom loading tool?
How do you take care of the dot matrix with a rear window like this?
like can i use the xpel ez tool to install the bottom loading without removing panel??
Hi, i have one question. What is your perfect slip solution ? With baby shampoo or dish soap ? How much solution for each ?
@Window Tint Warriors
South Africa?
you didn't need to shrink because your bottom loading?
What is that you are aplying on the rear window on the outside?
Great video, very professional 👏
The shop that i work at they always remove the door panel and sometimes the tint has a little bubbles.
Great video, time to get this 2021 5 series tinted 💪
Where do you buy your window film?
where are you guys from?
When you done all that you should remove windows . It take about 10min more. For removing just gasket you can pull out uper part of panels. No need to remove it.
The customer is going to be very happy with the car $200 to get your windows done very cool price
thank u brother
No more Xpel?
Do you add more soap to your solution being that your bottom loading?
No, same as always
Could you please tell me which Brand do you use a wet wipe before tightening the film? And what effect does it have? Thank you.
Donde consigo el papel en buen precio?
On a 2007 jeep compass can you just pop the top back of the panel.
Most cars that’s how it is
When it comes to luxury cars they are annoying af
Praise the camera man.
I also want to see you get a flat out and put it in a unger handle squeegee for film you won't to go back to the turbo
Awesome👏
blue towels are out of stock on the website (sad face)
www.windowtintsupplies.com/products/blue-window-cleaning-towels-4-pack
Can anyone tell me why there is a need to remove door panels if you can do a great job with panels on? Thank you
Yeah all respect for going the extra mile but why? Is it a way to charge more? Without the panel I get one micro creases on one side and they’re gone in 30 seconds with heat
Because i like to and its very easy for me. Everyone has their own method. Take what i show you and create a method that works best for you :) Cheers.
@@WindowTintWarriors thanks for the content!
when 2 staging sometimes you will get creases on the sides and have to chizel out. removing panels or sweeps you get a much easier and cleaner install because you can just drop the bottom of the film behind the panel with no obstruction
🤣🤣🤣scratch the scalp
Like & Thanks.
When you put the film on let it sit for a minute go and put another piece on and then come back and squeegee the film will not slide on you
Less soap my guy
I just had too much soap in the bottle.. letting it sit may actually allow the film to collect contamination or fall too low grabbing contaminates from the bottom of the glass.
@@WindowTintWarriors you ever use the multi gallon tanks? More to lug around but no more pump explosions lol
👏👌
😎🏆