hello. should i chose the apm internal compass or external compass option for calibration? there are different videos telling different things so I am confused. please help.
Hello ive seen lots of videos on how to set up the apm2.8 in mission planner i think I understand pretty well but my problem is is setting up my at9 failsafe , Ive seen one video where you change all the channel to failsafe including the throttle with a value of 51 and then setting your switches for all of your flight modes. So when i fly what mode do i have to be in just when im starting off or just go by my mission planner setup? I hope you understand what im saying thanks
Hi Pavel, great video and good idea the second method to calibrate the compass...so, could you tell me how you calibrate your ESCs with M.Planner because when it asks to push the green button i suppose it is "Start " to change "Ready" but when it ask "Push this button to enabled ESC Calibration and unplug, and plug in via usb" it's impossible because when i unplug usb the program blocked....so i run again M.Planner and once again on calibration Escs item.... i push "Start" without unplug but after i don't get goods tones....! Maybe you calibrate out of M.Planner with 4 in 1 such as 3Dr robotics video...? Thank's a lot for your answer Happy fly Philippe
can you please help me to figure out connections for using external compass with Gps. I've removed the jumper but bad compass health error is shown and when i'm trying to calibrate, it's not calibrating.
bro im using apm 2.6 i did accel calibration without quad(only apm via usb cable) after i connect apm to quad and i armed all motor running(without props) in same rpm if i tilt there is no changes in rotation can u help to work gyro?
+kraj Обращайся на ТЫ! Постоянно что-то дорабатываю. Желательно сразу ставить фирменные регуля и моторы. Эти не внушают доверия. 4шт регуля и 1 мотор уже сгорели. Из-за этих НОНЕЙМОВ каждый полет проходит в опасении. А так, для своей цены ок
Pixhawk Spektrum ar8010t not binding in mission planner to Dx8e I recently got into a person hobby of making drones do things. I had a parrot AR drone working fine with a raspberry pi but i wanted to make my own due to being able to add anything to one. I have posted a picture of what is going on with my drone in mission planner and the wiring of the drone. I have tried to wire the dsmx reciever to the pixhawk but i only get gray bars and no green. when i xonnect to the Ar8010t traditional reciever it gives me what shows in the picture. I am a newb and by no means a seasoned pro, I am just the first one at my university to want to get into drones and none of the teachers have a clue how to help me. I have programmed mission planner in python too using stml so it is just getting the hardware to work.drive.google.com/open?id=1wZES6pKk8EIMkwK3K1-QdNunNNioqdIx drive.google.com/open?id=1wZES6pKk8EIMkwK3K1-QdNunNNioqdIx drive.google.com/open?id=1bEBL-64ghWbyA3O-beEN_fO9dIYcPdI6 drive.google.com/open?id=1g__y_DynqI87qhC73hKCNpf5wBDXEuOx
hello. should i chose the apm internal compass or external compass option for calibration? there are different videos telling different things so I am confused. please help.
how do u setup the connection gimbal and its configuration, please i want to know
Калибровка компаса конечно очень крутая)))
)))
Hello ive seen lots of videos on how to set up the apm2.8 in mission planner i think I understand pretty well but my problem is is setting up my at9 failsafe , Ive seen one video where you change all the channel to failsafe including the throttle with a value of 51 and then setting your switches for all of your flight modes. So when i fly what mode do i have to be in just when im starting off or just go by my mission planner setup? I hope you understand what im saying thanks
Nice video can you send the prams you used, please?
Could you say if its possible to calibrate accel,compass by using radio (I can't plug the usb cable during calibration...) ?
Could you give any link for downloading the version of apm planner you used in the video.
what version mission planner do you use
Павел, Здравствуйте! Вы делали автотюн на этой раме? Можете показать пиды?
Привет. Делал, но потом откатил обратно. Сейчас заводские стоят.
Hi Pavel, great video and good idea the second method to calibrate the compass...so, could you tell me how you calibrate your ESCs with M.Planner because when it asks to push the green button i suppose it is "Start " to change "Ready" but when it ask
"Push this button to enabled ESC Calibration and unplug, and plug in via usb"
it's impossible because when i unplug usb the program blocked....so i run again M.Planner and once again on calibration Escs item....
i push "Start" without unplug but after i don't get goods tones....!
Maybe you calibrate out of M.Planner with 4 in 1 such as 3Dr robotics video...?
Thank's a lot for your answer
Happy fly
Philippe
Thanks To Philippe. Via M. Planner I have not calibrated controllers ESC. So, I don't even know what to tell you(
Call back
my drone is in telemetry always on head in planner - dunno why -seems like compass isnt workin`?
can you please help me to figure out connections for using external compass with Gps. I've removed the jumper but bad compass health error is shown and when i'm trying to calibrate, it's not calibrating.
bro im using apm 2.6 i did accel calibration without quad(only apm via usb cable) after i connect apm to quad and i armed all motor running(without props) in same rpm if i tilt there is no changes in rotation can u help to work gyro?
Call back 8294742253
Здравствуйте!!!у меня есть пара вопросов про Apm 2.8
Можете ответить или посоветовать хоть чтото?
спрашивай
Your PC cast so cool,what is it?
Nothing special. The computer case of Aerocool AeroEngine II
What's the ideal offset value for campus?
There is no fixed Val for the Compass it totally depends where you live.
@@kanadnemade thanks
yuo no poseo el rc telemetico , es necesarIO ?? paracalibar stickRadio link) tene que estra enchufado bateria
What is the mission planner version being used here?
Coz I'm on 1.3.44 and it does not support Reset to derault APM
Call back 8294742253
сам купил подобный набор. собираю инфу отовсюду. на данный момент остались довольны результатом?
+kraj Обращайся на ТЫ! Постоянно что-то дорабатываю. Желательно сразу ставить фирменные регуля и моторы. Эти не внушают доверия. 4шт регуля и 1 мотор уже сгорели. Из-за этих НОНЕЙМОВ каждый полет проходит в опасении. А так, для своей цены ок
+Pavel Karamelniy я так понял горели регули с read to sky?
да
+Pavel Karamelniy печаль. и регули и моторы оттуда. сечас какие моторы ?
те что в видео - с Ready to sky. Тоже но неймы. Сменил желтые (1000 KV) с переходной муфтой под пропы на эти белые (920 KV) с резьбой на валу мотора.
poderia disponibilizar o site do programa que você usou ?
firmware.ardupilot.org/Tools/MissionPlanner/
Hi..my apm2.8 in built compass not responding to my calibration...please help me ...
Call back 8294742253
Build drone #1 goo.gl/p5Wdrp
Build drone #2 goo.gl/YgCC7a
Build drone #3 goo.gl/X0ZRHo
Build drone #4 goo.gl/hCWUIh
Build drone #5 goo.gl/moAc51
Build drone #6 goo.gl/DNI6dm
Build drone #7 goo.gl/CJhMS5
Build drone #8 goo.gl/LIOFQE
Flight drone #1 goo.gl/xIZ6G8
Flight drone #2 LED goo.gl/rtG4iK
Flight drone #3 Xiaomi YI goo.gl/gZ3lFE
Flight drone #4 2-axis Gimbal goo.gl/j9fUab
Pavel Karamelniy
yes of course
когда полет планируете?
+kraj В этом году ? Ссылки на прошлогодние полеты в комментах
+Pavel Karamelniy Привет. Не подскажешь ты настраивал фейл сэйв ? Мне ни как не удается его настроить.
+kraj Привет. ruclips.net/video/SJ_2SmCeM4I/видео.html
+Pavel Karamelniy Смотрел уже. Мне конкретно radiolink не удается подружить с apm.
+kraj В чем заминка?
спасибо
Пожалуйста. Обращайся)
"What is the name of the song at minute 3.51" answer please
I forgot. That was a long time ago.
Pixhawk Spektrum ar8010t not binding in mission planner to Dx8e
I recently got into a person hobby of making drones do things. I had a parrot AR drone working fine with a raspberry pi but i wanted to make my own due to being able to add anything to one. I have posted a picture of what is going on with my drone in mission planner and the wiring of the drone. I have tried to wire the dsmx reciever to the pixhawk but i only get gray bars and no green. when i xonnect to the Ar8010t traditional reciever it gives me what shows in the picture. I am a newb and by no means a seasoned pro, I am just the first one at my university to want to get into drones and none of the teachers have a clue how to help me. I have programmed mission planner in python too using stml so it is just getting the hardware to work.drive.google.com/open?id=1wZES6pKk8EIMkwK3K1-QdNunNNioqdIx
drive.google.com/open?id=1wZES6pKk8EIMkwK3K1-QdNunNNioqdIx
drive.google.com/open?id=1bEBL-64ghWbyA3O-beEN_fO9dIYcPdI6
drive.google.com/open?id=1g__y_DynqI87qhC73hKCNpf5wBDXEuOx
сорри) видел сборку квадра,а вот что уже летали проглядел)
+kraj ничего) Обращайся!
www.gearbest.com/rc-parts/pp_109397.html для этих моторов не дорого.
+kraj не плохо!
bad
?