just a tip for anyone at 12.55 when he draws the rectangle and dose the symmetric relation, don't select the whole rectangle only the top and bottom line as well a centerline, watch his mouse very carefully and only select where he's selects
I'm from Indonesia, a student at the Muhammadiyah University of Riau. I'm interested in solidworks, and I'm working on a final project entitled Centrifugal Horizontal Casting. here I want to use the simulation solidworks horizontal casting from WTCL, can you help me make a tutorial for horizontal casting centrifugal in detail. I really hope your help, Thank you
but this doesn't make any sense i guess.....the rollers are free in contact (in reality roller should be in touch with the inside ring ) but in this design the rollers are not in contact with either of the inside ring or outside ring is this how it should be??? i don't know ...i am just asking!!
Hello friends, can someone show me that in solidworks I can change the color to make it look great from matte color. for example, when I take the color chromium plate, the color is matte, it is not as bright as in this video. where to set it? thank you
Sorry sir, can you share the work drawing link at the end of this video? when I look carefully after i drawn same bearing that i follow your all steps. There are a lot of mistakes. the first error occurred in the mismatch of the center bearing and center hole pattern at the roller after i assembled them, you can see at minute 24.05. the second error occurs because of the distance that is too large at the roller and inner ring. This is impossible sir..
If you take section view of the assembly you can see a gap between the roller and inner ring and interference between the roller and outer ring. Please tell how to fix this.
Hi Sir, your videos and lessons are very good, and i was following them regularly when unfortunately i loosed my Solidworks, so i'm looking for a new install or download, could u help me where to find it please?
i have a problem with the first part , i cant draw fillet it says : the fillet could not be added because the specified radius would eliminate on of the elements
Thanks for the instant reply .... Your videos are really awesome....!!! But by any ways if I arrange the graphics card, then are there any extra settings to be done ?
thanks for this videos, i like it
welcome bro,
Thank u so much sir very nice tutorial sir ...again thanks
I just done my first animation following this tutorial. Many thanks.
just a tip for anyone at 12.55 when he draws the rectangle and dose the symmetric relation, don't select the whole rectangle only the top and bottom line as well a centerline, watch his mouse very carefully and only select where he's selects
Best solidworks tutorials by far! Thank you very much for taking the time to upload these videos!!!
Thanks,
Very nice tutorial. Keep doing it sir. Your all videos are very informative.
Thanks,
Excellent tutorial.
Thank you for the tutorial.
Could you please suggest where to get dimensions for bearings?
Armen Miskarov ya please
meron ba kayong alam na tapeted roller bearing size 16284/16150 any kind of brand
Hey,
Can you please share the link for this file?
Hello sir.
Your design Bearing using SolidWord version?
2016 / 2017??
I'm from Indonesia, a student at the Muhammadiyah University of Riau. I'm interested in solidworks, and I'm working on a final project entitled Centrifugal Horizontal Casting. here I want to use the simulation solidworks horizontal casting from WTCL, can you help me make a tutorial for horizontal casting centrifugal in detail. I really hope your help, Thank you
Its not proper design. You tried it well with available dimensional data. But actual internal geometry is bit different in TRB
but this doesn't make any sense i guess.....the rollers are free in contact (in reality roller should be in touch with the inside ring )
but in this design the rollers are not in contact with either of the inside ring or outside ring
is this how it should be???
i don't know ...i am just asking!!
Strictly following your an excellent tutorials. Regards from Baku, keep it up.
Hello friends, can someone show me that in solidworks I can change the color to make it look great from matte color.
for example, when I take the color chromium plate, the color is matte, it is not as bright as in this video.
where to set it?
thank you
Sorry sir, can you share the work drawing link at the end of this video? when I look carefully after i drawn same bearing that i follow your all steps. There are a lot of mistakes. the first error occurred in the mismatch of the center bearing and center hole pattern at the roller after i assembled them, you can see at minute 24.05. the second error occurs because of the distance that is too large at the roller and inner ring. This is impossible sir..
very nice sir.pls add the video of car assembly also
Thanks i will do car tutorial soon.
At the assembly i have many problems can you help me?
tell me
If you take section view of the assembly you can see a gap between the roller and inner ring and interference between the roller and outer ring. Please tell how to fix this.
Dear thank you for this tutorial please say me where should I change the diameter of bearing outer and inner diameters
Hi Sir, your videos and lessons are very good, and i was following them regularly when unfortunately i loosed my Solidworks, so i'm looking for a new install or download, could u help me where to find it please?
Very nice, I love it :)
i have a problem with the first part , i cant draw fillet it says : the fillet could not be added because the specified radius would eliminate on of the elements
How do you get the polished appearance while initial stages of modeling only ?
you need professional graphics card in your system like Nvidia Quadro series or AMD firpro Series. other cards will not support real views.
Thanks for the instant reply .... Your videos are really awesome....!!! But by any ways if I arrange the graphics card, then are there any extra settings to be done ?
no need any extra settings.
How can I sketch this in autodesk inventor? You should make a tutorial of these!
23.10, how to select construction line on roller? cheers
thanks problem solved
Great,
excellent demonstration congratulations thanks and regards
Keep slow video to clear understanding
How you are mating going very fast you are
nice tutorial
How do you get the stainless steel looks like a mirror?
WE NEED DIAGARAM IN SCREEN WE CAN ESILY UNDERSTAND SIR
Big fan of CADCAM titorial
can you upload the simulation video for this
Great tutorial!!!!!!!!!!!!11
Thanks
Great sir
Thanks
Are you indian
thank thank thank thankkkkkks😊😊
well done
Thanks
Thanks,
welcome, please share our videos which is help us to do more and more in Solidworks thanks,
good
Thanks,
Fantastic very impressive
Shawawt holy
102.17 102.78
Thanks
Good
😍😍😍😍