Your a legend man. Now at least I have my remote controller 2 inputs registering. I can`t tell you how long I have been scouring the internet for this. Thanks
You bet! I struggled the same way I’m sure you have been. I couldn’t do it alone, but that’s what is so great about the community - there’s always somebody willing and able to help! Good luck, happy flying!
Just want to say THANK YOU for going over this setup! Between this video and 2 others I was finally able to get my new Pavo 20 up. Unlike the new Pavo Pico I ordered first that never got in the air despite following every step.
Hi Drone Geek! Tks in advance for all your information! I have a question regarding to the modes section, I can´t find the AIR MODE in this betaflight firmware 4.4.1 and there are others modes that doesn´t appear in this video? Can you tell me what to do! Please!! I´m new fpv pilot so anything that you can help I´ll be very gratefull! Regards from Bucaramanga, Colombia, South America!!
Hello! Over the last few months I've been talking with end-users who did not have luck with my video initially when configuring their BETAFPV drones as per the instructions I outlined. My best advice for you is to start by reflashing the firmware of your AIO FC/ESC from BETAFPV's official website. While not a 100% success rate, I'm finding a lot of end-users who had been having trouble finding certain menus, settings, and configurations before were able to solve these issues after reflashing the firmware.
I remember when I got one of my first drones and I couldn’t connect to betaflight. Turns out I was plugging into the camera unit instead of the esc/fc stack😂
appreciate the content. i've had mine configured b4 but then i tried to update the firmware then it got messed up. question. now its seems that my accro mode isn't really fully manual. i can literally let go of the sticks and it kinda hovers in place. it says it's in accro, in betafpv config it says ARM aux 2 (i want it on the other side). numbers are exactly as yours but when flying it's just does't feel fully manual. is there anything else i can check or do to get full manual? appreciate any feed back
Hi, I have a question: I have the latest Googles 3 and the last controller Dji fpv rc 3 And I want to know if it will work with the O3 unit And is there a way to connect the O3 To stack so that the remote will work?
Hey, I just got my Pavo20 today and paired it to the Radiomaster Boxer (works Good). I added the O3 onto the drone and when the drone is powered on, the O3 won't have ony lights on it or be able to bind. Do you know of anything to do?
Double-check the cable is snuggly connected to the AIO FC/ESC onboard the drone. If it seems secure, try unplugging it and blowing the port on the drone out with canned air as well as the port inside the O3 Air Unit. Also, use the cable that comes with the drone, not the one that comes with the air unit. Idk why, but using the cable that comes with the air unit can cause issues with the drone. If none of that works, you may have a power supply issue with either the drone or the air unit and should consult the appropriate manufacturer.
I have followed this to the T. No matter what I do I cannot get any movement on the receiver table when I move the sticks around on the controller I have tried this process with the rc2 with the goggles V2 and the goggles 3 with the rc3 and it's the same thing I get no communication. Might have to do a flash/ firmware.. this was supposed to be so simple and plug and play I can't believe I'm this confused(pavo 20 pro nightfire)
Hello there im kinda new in this but, i had dji avata before and i bought a PAVO20 as u guess, so now i did the 90% of the work i binded all the devices and applied betafly settings. I watched lot of videos but didnt get the right answer yet. So the problem is when i try to arm the drone its closing and opening again. Its resetting itself. While it happening HD icon's bar is rising down slowly and right after that its closing. I gived 10 hours to make it work and i believe i deserved a little bit help. Even from now i thank you for your helpful messages.
You're an absolute lifesaver! I am facing one last issue though. Once the drone is armed, the throttle goes to 100% and i cannot bring it down unless i disarm it. I tried to do the same in BetaFlight motor test (without props) but for some reason the motors are going full throttle after arming. Any ideas?
None unfortunately. Maybe check your throttle settings in the receiver menu? My other suggestion would be to check out your modes tab to see if you have an AUX input that is incorrect. That may be a good one to take to Reddit. I’m sorry I’m not of more help.
This may be a stupid question. When plugging the drone into the computer does the battery need to be connected as well? Its not recognizing the 03 unit as being on when i plug it in. all my connections seem tight just cant figure out why everything is on when plugged in usb but not the 03
It depends on what port you’re plugging into. If plugging into the O3 Air Unit directly, you do NOT need a battery to supply power. If plugging into the airframe, you DO need a battery to supply power to have access to certain features.
Question: Will I still be able to easily connect my controller and goggles to my DJI Avata also if I want to use that instead, or does this limit me to only using my Pavo drone going forward?
Yes. The DJI Goggles 2 and FPV Controller 2 do not require rebinding when swapping between devices. All you have to do is select the correct device from that device menu where we selected the O3 Air Unit. Once the goggles are looking for the correct device, they will pair with devices they already know from the initial binding.
Awesome, last question. Does the O3 air unit adhere to the same software flight restrictions that the Avata and other drones are subject to? Aka no fly zone restrictions
Good afternoon ! First of all, thank you very much for the tutorial, I have seen it about 10 times and I have carried it out step by step, and it still does not assemble the engines. What can be ? I have the turkey 20 with the DJI Goggles 2 and DJI FPV Controller 2
Genuinely asking...is "Turkey 20" a typo? Because if it is, do you mean you have the Pavo 20...and if it isn't, then where the hell can I get a drone called the "Turkey 20," because I absolutely will be getting one...
That's a great question -- I can't verify whether or not it works with the Defender 20 or not -- I had somebody ask a similar question about a GEPRC drone -- it might, but I cannot say for sure. I'm sorry I couldn't be more helpful!
Interesting video. Thanks for publishing it. Thanks to you I was able to start using my npavo20 with the DJI googles 2 and the DJI controller Perhps I might get some help from you.... Just modifying things on betaflight I had to start from the scratch and I cannot configure the led strip to turn it off and on with my controller.... I obtained USER1 in Betaflight modes, the button I assigned on the controller works BUT led does not turn off and on.... I guess it is something to do with congiguragtion of the LED Strip on betaflight... but there is no way I helping hando would be highly appreciated TRhanks
@@TheDroneGeek Thanks... I'll be awaiting for your answer..... In betaflight, user1 gets on and off when I press AUX4, but leds remain on.... I also noticed that when I restarted everything the opyion LED Strip in Betaflight was empty, something that did not happen before...
@@TheDroneGeek hi again! I managed to go back though my paces and as a saved the previous CLI file configuration, I installed it and followed your indications from scratch.... everything seems to work, including the leds... Don't ask me why.... but when back to normal... the only thing, the OSD, that behaves in a funny way as the crosshair is not in the centre (it happened to you as well in your video) and also it does not show anything from the OSD. Many thanks for your video, again... If you have a clue how to get the OSD better, please, let us know
OH man, thanks to you and reditt guy, why does the official website get the uart port wront and dont give you all this information. Can I recommend they use your video officially?
When you have the drone on and connected to Betaflight, it will not arm. It's a safeguard that prevents unwanted arming and take-offs while you are configuring it. Unhook it from Betaflight and try to arm again.
Great question. Code can and should go in all at once. I don’t know that going section by section would hurt anything, but in all of the instruction I’ve been given and the other tutorials I see online for CLI in Betaflight, just dumping it all in there works just fine.
VERY INTERESTING VIDEOS.., It looks as if you do not need to get into betaflight to mess around for synch. the DJI controller... And by the way... I heard the DJI Controller is not working with the PAVO 20 POCKET It looks like the POCKET version has sensors pointing down in order to create estability... I am buying the pavo 20 but I( am thinking about buying also the POCKET one bevause I normally use it for interiors. am I right bout the POCKET version? Well.... I wrote that at the beg. of your video, so I see I have to get into betaflight... But still my question about the POCKET is there... Could you help?
Hello how are you ? I just got the pavo pico with the o3 air system. It was flying fine at first. Bust after few flights i got some warning message in the goggle. ( rcsmoothing, rxloss and baudx or something like that) Now the drone doesnt recognise the Rc anymore. I still have the image in the goggle. The rc is bind to the goggle but its not to the drone anymore. Any idea i could fix this up ? Its really annoying i just got it 2 days ago.. I have the impression that it might be the pin s-bus of the o3 who get a malfunction. Heeeeelp pleaase 😅
It is still not working for me Im using nazgul ECO with rc2 and the revire tab in betaflight is still not working. Do you have any idea how to fix this?
When you’re using the air unit to pair the controller it requires you to bring the throttle to 0 in order to arm. You will not be able to use DJI peripherals to arm without bringing the throttle down as an arm redundancy.
Actually, I think with the Goggles 2 you just have to pair once and then the goggles pick up and connect to the devices they remember. I’ve never had to re-pair with a drone using the Goggles 2 that I can recall. You should be able to bounce in and out of different drones - same goes for the controller 2.
Thank you for the great explanation. Just one simple question; Can I record video without Googles. There is a sd card slot on O3. Can I use video record button on Dji Rc2 to recording? Thank you..
Thanks for the comment. I put a lot of work into it and didn't expect it to get a lot of attention because it's a rather specific problem, but the fact you took the time to say something kind about it makes that work worth it. I appreciate it and you!
my pavo flips out, after doing everything correctly following the video....loved THE VIDEO, but do you know why it would? thank you SO MUCH BROTHER!!!!!!!
Check your motor direction in Betaflight. Toggle on and off (and test with each setting respectively) the "motor order reversed" toggle. If that does not solve the issue, restore it back to the position it is in during my video tutorial and try turning "low power mode" on in your goggles. I recently had an issue where my Pavo Pico was being told it was rolling to the right when I was giving no stick input, which made takeoff impossible because it would just flip over when I gave it any throttle. That said, if it still doesn't work, try going to this website and reflashing the firmware via the CLI to factory defaults. Then try the process over again: support.betafpv.com/hc/article_attachments/21131998083865
Not confirmed. You could try it and if it doesn’t work you could just re-flash the drone’s original firmware and start from square one. I imagine it might work because the GEPRC drones are formatted similarly to the BETAFPV drones.
No it didn’t. Reflash it with factory firmware or input the factory CLI: support.betafpv.com/hc/en-us/articles/23244448530201-CLI-and-Firmware-for-Pavo-20-F405-2-3S-20A-V1-0-FC
I haven't tested to confirm, BUT the Goggles 3 and Controller 3 are compatible with the O3 Air Unit...so in theory it SHOULD work. I can't make any guarantees though. Please be advised -- there is a bug with the Goggles 3 when paired with the O3 Air Unit it will randomly drop feed and connection during flight. I'm sure they're going to fix this in the near future...but right now I would advise against using the Goggles 3 with the O3 Air Unit until they get it sorted.
@@TheDroneGeek yeah I’m aware of the bug. I’m certain they’ll fix it too but idk how long that will be. So it’s either buy something like this and hold out for a FW update or get something like the NEO that works but is less capable.
![ROSÉ(로제) - APT. (Band VER.) (With. 이영지) [더 시즌즈-이영지의 레인보우] | KBS 241129 방송](http://i.ytimg.com/vi/IW8qaemx74g/mqdefault.jpg)
Your a legend man. Now at least I have my remote controller 2 inputs registering. I can`t tell you how long I have been scouring the internet for this. Thanks
You bet! I struggled the same way I’m sure you have been. I couldn’t do it alone, but that’s what is so great about the community - there’s always somebody willing and able to help! Good luck, happy flying!
@@TheDroneGeek AGREED OMFG THAT YOU SO MUCH ITS BEEN AT LEAST 5 HOURS THANK THANK THANK YOU SOOO MUCH
Just want to say THANK YOU for going over this setup! Between this video and 2 others I was finally able to get my new Pavo 20 up. Unlike the new Pavo Pico I ordered first that never got in the air despite following every step.
Check your firmware for the Pavo Pico. May need to reflash the AIO to get it to work.
Hi Drone Geek! Tks in advance for all your information! I have a question regarding to the modes section, I can´t find the AIR MODE in this betaflight firmware 4.4.1 and there are others modes that doesn´t appear in this video? Can you tell me what to do! Please!! I´m new fpv pilot so anything that you can help I´ll be very gratefull! Regards from Bucaramanga, Colombia, South America!!
Hello! Over the last few months I've been talking with end-users who did not have luck with my video initially when configuring their BETAFPV drones as per the instructions I outlined. My best advice for you is to start by reflashing the firmware of your AIO FC/ESC from BETAFPV's official website. While not a 100% success rate, I'm finding a lot of end-users who had been having trouble finding certain menus, settings, and configurations before were able to solve these issues after reflashing the firmware.
I remember when I got one of my first drones and I couldn’t connect to betaflight. Turns out I was plugging into the camera unit instead of the esc/fc stack😂
It happens to the best of us 😂
Thank you, Papa!
😘
@@TheDroneGeek❤❤
appreciate the content. i've had mine configured b4 but then i tried to update the firmware then it got messed up.
question.
now its seems that my accro mode isn't really fully manual. i can literally let go of the sticks and it kinda hovers in place.
it says it's in accro, in betafpv config it says ARM aux 2 (i want it on the other side). numbers are exactly as yours
but when flying it's just does't feel fully manual.
is there anything else i can check or do to get full manual?
appreciate any feed back
Hi, I have a question: I have the latest Googles 3 and the last controller Dji fpv rc 3 And I want to know if it will work with the O3 unit And is there a way to connect the O3 To stack so that the remote will work?
Hey, I just got my Pavo20 today and paired it to the Radiomaster Boxer (works Good). I added the O3 onto the drone and when the drone is powered on, the O3 won't have ony lights on it or be able to bind. Do you know of anything to do?
Double-check the cable is snuggly connected to the AIO FC/ESC onboard the drone. If it seems secure, try unplugging it and blowing the port on the drone out with canned air as well as the port inside the O3 Air Unit. Also, use the cable that comes with the drone, not the one that comes with the air unit. Idk why, but using the cable that comes with the air unit can cause issues with the drone. If none of that works, you may have a power supply issue with either the drone or the air unit and should consult the appropriate manufacturer.
I have followed this to the T. No matter what I do I cannot get any movement on the receiver table when I move the sticks around on the controller I have tried this process with the rc2 with the goggles V2 and the goggles 3 with the rc3 and it's the same thing I get no communication. Might have to do a flash/ firmware.. this was supposed to be so simple and plug and play I can't believe I'm this confused(pavo 20 pro nightfire)
Hi! Will the CLI (last part) work on the new Firmware 4.5 for the Pavo Pico and the setup with the DJI RC 2?
It should. I have not heard any issues. I can check with my contact at BETAFPV and follow-up on this thread if they give me a response!
Hello there im kinda new in this but, i had dji avata before and i bought a PAVO20 as u guess, so now i did the 90% of the work i binded all the devices and applied betafly settings. I watched lot of videos but didnt get the right answer yet. So the problem is when i try to arm the drone its closing and opening again. Its resetting itself. While it happening HD icon's bar is rising down slowly and right after that its closing. I gived 10 hours to make it work and i believe i deserved a little bit help. Even from now i thank you for your helpful messages.
Thanks, Well Done!!!
You're welcome and thank you!
This video is an absolute GODSEND. THANK YOU!
You're an absolute lifesaver! I am facing one last issue though. Once the drone is armed, the throttle goes to 100% and i cannot bring it down unless i disarm it. I tried to do the same in BetaFlight motor test (without props) but for some reason the motors are going full throttle after arming. Any ideas?
None unfortunately. Maybe check your throttle settings in the receiver menu? My other suggestion would be to check out your modes tab to see if you have an AUX input that is incorrect. That may be a good one to take to Reddit. I’m sorry I’m not of more help.
Did you calibrate gyroscope ? I had similar issue after firmware flash. Even though drone looked leveled it was required to do.
Earned a sub on this one saved me from losing it and throwing this FPV 2 controler across the room . 😂
I’m happy to hear you still have an in-tact controller. 😂
This may be a stupid question. When plugging the drone into the computer does the battery need to be connected as well? Its not recognizing the 03 unit as being on when i plug it in. all my connections seem tight just cant figure out why everything is on when plugged in usb but not the 03
It depends on what port you’re plugging into. If plugging into the O3 Air Unit directly, you do NOT need a battery to supply power. If plugging into the airframe, you DO need a battery to supply power to have access to certain features.
Question: Will I still be able to easily connect my controller and goggles to my DJI Avata also if I want to use that instead, or does this limit me to only using my Pavo drone going forward?
Yes. The DJI Goggles 2 and FPV Controller 2 do not require rebinding when swapping between devices. All you have to do is select the correct device from that device menu where we selected the O3 Air Unit. Once the goggles are looking for the correct device, they will pair with devices they already know from the initial binding.
Awesome, last question. Does the O3 air unit adhere to the same software flight restrictions that the Avata and other drones are subject to? Aka no fly zone restrictions
Good afternoon ! First of all, thank you very much for the tutorial, I have seen it about 10 times and I have carried it out step by step, and it still does not assemble the engines. What can be ?
I have the turkey 20 with the DJI Goggles 2 and DJI FPV Controller 2
Genuinely asking...is "Turkey 20" a typo? Because if it is, do you mean you have the Pavo 20...and if it isn't, then where the hell can I get a drone called the "Turkey 20," because I absolutely will be getting one...
@@TheDroneGeek The Turks are tough.. hehehe, it's pavo 20, translation error was
great video, but sadly did not work with my pavo20 😔
i had the wrong firmware, now it works. Thank you so much 😊
Great video! do you know if these settings will work with the iflight defender 20 with a dji 03 air unit?
That's a great question -- I can't verify whether or not it works with the Defender 20 or not -- I had somebody ask a similar question about a GEPRC drone -- it might, but I cannot say for sure. I'm sorry I couldn't be more helpful!
how do i get USER1 to appear in the MODE tab? I don't see that option
Interesting video. Thanks for publishing it. Thanks to you I was able to start using my npavo20 with the DJI googles 2 and the DJI controller
Perhps I might get some help from you....
Just modifying things on betaflight I had to start from the scratch and I cannot configure the led strip to turn it off and on with my controller....
I obtained USER1 in Betaflight modes, the button I assigned on the controller works BUT led does not turn off and on....
I guess it is something to do with congiguragtion of the LED Strip on betaflight... but there is no way
I helping hando would be highly appreciated
TRhanks
Let me take some time to look into this and see if I can figure anything out. Thank you for commenting!
@@TheDroneGeek Thanks... I'll be awaiting for your answer..... In betaflight, user1 gets on and off when I press AUX4, but leds remain on.... I also noticed that when I restarted everything the opyion LED Strip in Betaflight was empty, something that did not happen before...
@@TheDroneGeek hi again! I managed to go back though my paces and as a saved the previous CLI file configuration, I installed it and followed your indications from scratch.... everything seems to work, including the leds... Don't ask me why.... but when back to normal...
the only thing, the OSD, that behaves in a funny way as the crosshair is not in the centre (it happened to you as well in your video) and also it does not show anything from the OSD.
Many thanks for your video, again...
If you have a clue how to get the OSD better, please, let us know
@@TheDroneGeek i put the cli in and now my motor direction is all random
This video is amazing. When I throttle up my Pavo20 everything freaks out and it spins around. The inputs look correct in Betaflight... any ideas?
Check your propeller orientation. It should be in a “props out” setup.
@@TheDroneGeek Correctly in Props out.. I get a "runaway" in my goggles
OH man, thanks to you and reditt guy, why does the official website get the uart port wront and dont give you all this information. Can I recommend they use your video officially?
You can! I'm not sure they will -- but I do have a great relationship with them, so maybe! :)
Great vid. Thank you🙏
well, get my gogles and controller now working, BUT Arm says its DISABLED and looks red in betafligth
When you have the drone on and connected to Betaflight, it will not arm. It's a safeguard that prevents unwanted arming and take-offs while you are configuring it. Unhook it from Betaflight and try to arm again.
@@TheDroneGeek got it 🙏🤟👍 thanks for sharing all your thoughts. Respect to you, i will totally follow you in future more and more ..
Thanks for the video followed your steps and good to go!
Should you copy and paste all the code at the same time or one at a time?
Great question. Code can and should go in all at once. I don’t know that going section by section would hurt anything, but in all of the instruction I’ve been given and the other tutorials I see online for CLI in Betaflight, just dumping it all in there works just fine.
VERY INTERESTING VIDEOS..,
It looks as if you do not need to get into betaflight to mess around for synch. the DJI controller...
And by the way... I heard the DJI Controller is not working with the PAVO 20 POCKET
It looks like the POCKET version has sensors pointing down in order to create estability... I am buying the pavo 20 but I( am thinking about buying also the POCKET one bevause I normally use it for interiors.
am I right bout the POCKET version?
Well.... I wrote that at the beg. of your video, so I see I have to get into betaflight...
But still my question about the POCKET is there...
Could you help?
Hello how are you ?
I just got the pavo pico with the o3 air system.
It was flying fine at first. Bust after few flights i got some warning message in the goggle. ( rcsmoothing, rxloss and baudx or something like that)
Now the drone doesnt recognise the Rc anymore.
I still have the image in the goggle. The rc is bind to the goggle but its not to the drone anymore.
Any idea i could fix this up ?
Its really annoying i just got it 2 days ago..
I have the impression that it might be the pin s-bus of the o3 who get a malfunction.
Heeeeelp pleaase 😅
It is still not working for me Im using nazgul ECO with rc2 and the revire tab in betaflight is still not working.
Do you have any idea how to fix this?
This tutorial only applies to the BETAFPV series of prebuilt drones with the O3 Air Unit. I cannot advise you on a different build. I'm sorry!
@@TheDroneGeek oh okay I have a pre built drone but yes not the right series.
Thank you anyway
Hi im new to fpv, will this apply to the new dji goggles and contoller 3 from the avata 2?
if i go to ports it only goes up to aurt 4 and lpaurt1
Will it work on a mobula8 with 03 air unit?
Hi Bro, So I don't need to change the Throttle stick down?
When you’re using the air unit to pair the controller it requires you to bring the throttle to 0 in order to arm. You will not be able to use DJI peripherals to arm without bringing the throttle down as an arm redundancy.
Merci beaucoup !
Simply, THANKS
Is paring back to a official DJI drone simple u just change the device on googles and put remote 2 in paring mode to connect to DJI FPV
Actually, I think with the Goggles 2 you just have to pair once and then the goggles pick up and connect to the devices they remember. I’ve never had to re-pair with a drone using the Goggles 2 that I can recall. You should be able to bounce in and out of different drones - same goes for the controller 2.
Thank you for the great explanation. Just one simple question; Can I record video without Googles. There is a sd card slot on O3. Can I use video record button on Dji Rc2 to recording?
Thank you..
Good setup video.
Thanks for the comment. I put a lot of work into it and didn't expect it to get a lot of attention because it's a rather specific problem, but the fact you took the time to say something kind about it makes that work worth it. I appreciate it and you!
thank god i found this video
my pavo flips out, after doing everything correctly following the video....loved THE VIDEO, but do you know why it would? thank you SO MUCH BROTHER!!!!!!!
Check your motor direction in Betaflight. Toggle on and off (and test with each setting respectively) the "motor order reversed" toggle. If that does not solve the issue, restore it back to the position it is in during my video tutorial and try turning "low power mode" on in your goggles. I recently had an issue where my Pavo Pico was being told it was rolling to the right when I was giving no stick input, which made takeoff impossible because it would just flip over when I gave it any throttle.
That said, if it still doesn't work, try going to this website and reflashing the firmware via the CLI to factory defaults. Then try the process over again:
support.betafpv.com/hc/article_attachments/21131998083865
Btw...I'm going to ask just for the sake of covering all my bases...did you check your propeller installation? It should be configured for "props-in."
Pavo 25v2 the fking controller is connected and nothing happens in beta fly when i press a button. After all this….
What controller and goggles are you using?
will these same steps work with the geprc mark5
Not confirmed. You could try it and if it doesn’t work you could just re-flash the drone’s original firmware and start from square one.
I imagine it might work because the GEPRC drones are formatted similarly to the BETAFPV drones.
THAT CLI BRICKED MY PAVO
No it didn’t. Reflash it with factory firmware or input the factory CLI:
support.betafpv.com/hc/en-us/articles/23244448530201-CLI-and-Firmware-for-Pavo-20-F405-2-3S-20A-V1-0-FC
hi nice video. would you be so kind to explain to me why i have to change the lop pid frequency from 8.00 to 2.00 kHz? thanks
Will this work with DJI Goggles 3 and FPV Controller 3?
I haven't tested to confirm, BUT the Goggles 3 and Controller 3 are compatible with the O3 Air Unit...so in theory it SHOULD work. I can't make any guarantees though. Please be advised -- there is a bug with the Goggles 3 when paired with the O3 Air Unit it will randomly drop feed and connection during flight. I'm sure they're going to fix this in the near future...but right now I would advise against using the Goggles 3 with the O3 Air Unit until they get it sorted.
@@TheDroneGeek yeah I’m aware of the bug. I’m certain they’ll fix it too but idk how long that will be. So it’s either buy something like this and hold out for a FW update or get something like the NEO that works but is less capable.
did you ever get this to work? I would like to get it working and wait for the FW update to fix the feed drops
#betafpv #pavopicodjibind #pavopico #betafpvbinddji #dronefix