Good morning, Thank you very much for uploading this educational videos. That is very appreciated. I have a ps4 slim that will not recognize my controller in either of the front usb ports. I used a USB tester, and and I an getting 5V, but th wired controller that I use does not go into charging mode like it usually does on a normal ps4. I tried swapping the BT module but that did not fix the issue instead the ps4 would not turn on. Maybe I applied to much heat to the donor chip and I end up runing it. Could it be that maybe the USB CHIP that control the USB ports went bad and it needs to be replace? If that is the case what is the name of that chip? Thank you!
Hello, good contribution. Something curious happened to me. With the ATX power supply it turns on without problems, but if I try with its power supply it does not turn on. I've tried a new one and it's still doing the same thing. Any advice? Greetings
Hi, from which places can I get 12 volt on a PS4 Slim ? I removed the internal hard disk, I put a sata extension and the 12 volt is missing for the 3.5 disk of 4TB WD40EZRZ, this disk get 5v 0.6 A and 12v 0.45A, the original Toshiba 2.5 of 1TB says 5v 1A, thanks
I opened the power supply and 12v is the main output voltage, I did not know, I soldered a wire to the output of the supply and the 4 TB WD40EZRZ SATA disk was working :-) (These from sony! All to save a thick 12v track on the SATA output)
Hey hows it going today i tried to fix an ADP-200ER (for the 1200 series ps4) which has no power the ps4 beeps once the 12V does not kick in, i opened up the power supply and there was alot of dust in it .I cleaned it and checked all the power IC and transistors for shorts i could not find anything short the big fusible resistor was also good . Do u know what could be bad that prevents the 12V from kicking in ?
thanks for your reply . which pmic are you referring to ? DAP041 ?The funny thing is i just tried it and its started to work . i guess we can call it an intermittent power supply . I'll take a look under the microscope to see if anything is burnt .
hola tengo una fuente de ps4 u.slim que anda y a los 15 minuitos se apaga.. probe con otra y anda bien el tema que se caen los 12v que tengo que reemplazar. gracias
What could the potential problem be in my case I am working with the same psu ADP 160er, system turns on loads up just fine until around the 5 minute mark. Then beeps twice simultaneously and system shutdowns? (No warning signs whatsoever)This happened multiple times, remind you the councle I'm working with is clean and quiet, I've checked the psu and cannot fine anything out of the regular? Please Help! Thanks All
well im prettty sure tha roaches fried mine. i done tried swapping out the whole power supply with no luck appqarently i was given another bad one . and i just bought sonic mania and i didnt ger to beat it yet. so now im stuck wondering what to do next. ithink lll ttry the resistor like.you.did.on this video
mighty mouse "saves the day" --Danger Mouse was that weird british cartoon along side banana man (on Nickelodeon in the early 80's). i think the feature film y'all mentioned was maybe "under dog".
OMG, is this another part from "idiots at work"? Sir please use a adjustable power source or a simple lamp in row to the power supply to protect the resistor and other parts.
Thank you, brother, I have taken advantage of you.I am following you from Iraq.
Everyone talking about electronics, but I see that nail on your pinky ;)
🤣
Hey, throw it around like an asshole....don't be sending anything to this mighty mouse, he will break it some more!
excellent tutorial, it was a great help to repair the power supply
Thanks mate! Just managed to fix the psu. It was the zener diode only faulty
Hi! My zener diode is also faulty. Can you please tell me the value of it? I cant see, it is so small
DZ39 da placa fonte: ADP-160FR AAA, sabe o valor, código e quantos volts?
hi, i have a problem my power supply does not generate 12v, what could be failing?
Lol bang it around some more like Mighty Mouse
i remember that cartoon. chip & dale a good classic.
Good morning,
Thank you very much for uploading this educational videos. That is very appreciated.
I have a ps4 slim that will not recognize my controller in either of the front usb ports. I used a USB tester, and and I an getting 5V, but th wired controller that I use does not go into charging mode like it usually does on a normal ps4. I tried swapping the BT module but that did not fix the issue instead the ps4 would not turn on. Maybe I applied to much heat to the donor chip and I end up runing it.
Could it be that maybe the USB CHIP that control the USB ports went bad and it needs to be replace? If that is the case what is the name of that chip?
Thank you!
Parabéns pelo reparo virei fã do canal ,
Congratulations on the repair I will become channel fan
o cara é fera
I have a PS4 slim power supply i need a MOSFET controller chip number is MPS1723-HR1001C. Do you know where i can source that part? Thanks in advance.
thanks good vídeo, Can you tell me where you bought the resistance, I can't get it anywhere
In my faulty ps4 power supply IC 101 pin 2 and 8 are shorted is this ok ?on a good power supply please give me a reference thanksss
adp-240 repair video please
What’s the difference between the ADP-160ER and the ADP-160CR?
Hello, good contribution. Something curious happened to me. With the ATX power supply it turns on without problems, but if I try with its power supply it does not turn on. I've tried a new one and it's still doing the same thing. Any advice? Greetings
What is the zener diode reference you changed?
what is adp-160er and 160cr difference?
What's the part number for mp6922l and mp6922 on Mouser or DigiKey? As far as I'm aware it's an IC chip labeled on the board as IC101.
Hello!!! Please tell me the name of the diode D101 (I don’t see the markings)!!! Thanks a lot for the help...
ADP-160ER PS4
Hi sir
Can you tell me the currently changed IC as well as Mosfet its part
number
in your video u plz show multimeater how to check component
Hi legion, please whatsvthe part number for the zener diode and the fet
Mine is 160fr.. Same process is required for repairing right
I have a power supply that turns off the ps4 and checking the voltages the 12 do not trigger. can you help?
two 450v caps and you weren't even concerned about not discharging them?
How many ohm is that resistor at 7:25
I think 0.16 ohms
16.8 ohms 1/2 watt.. 2%
So many resistors HAHA glad you figured it out. You stopped talking though, what did you figure out the mosfet?
Do you worry about discharging those big caps before working on the power supply?
Darren Rutgers in the PS4 pro powers supply. Yes. On previous versions. No. I know what I can touch. And not touch. But it is recommended
Definitely never heard of super chicken lmao
that Duck Tales three-parter you can't find is the feature film.
kevin Deal ohhhhj. Lol
The char when the resistor blew the second time... Coating the inside of the ps with black carbon, lol
Instructions Unclear
🔥
House is now an Atomic Bomb 💣
Is the part adp-160er different than the adp-160cr. I can only find this one. Want to know if it is compatible
Hi, from which places can I get 12 volt on a PS4 Slim ? I removed the internal hard disk, I put a sata extension and the 12 volt is missing for the 3.5 disk of 4TB WD40EZRZ, this disk get 5v 0.6 A and 12v 0.45A, the original Toshiba 2.5 of 1TB says 5v 1A, thanks
I opened the power supply and 12v is the main output voltage, I did not know, I soldered a wire to the output of the supply and the 4 TB WD40EZRZ SATA disk was working :-)
(These from sony! All to save a thick 12v track on the SATA output)
Great job sir
Can you help me with a same power supply but it turns on the system then off. Thanks in advance
I just watched this to see how the power supply is made, disappointed of how much cooling those transistors are getting.
What is name of Q9 ?
I don’t get continuity on ZD801 & ZD802. Should I? & if they’re defective, what are they so I can replace them? Thanks!
Same problem I have one with continuity and one without , which is correct and what is the part name I have to buy? thanks in advance for any help
GREETINGS I REQUIRE TO KNOW THE Q41 TRANSISTOR SPECIFICATION. TO REPLACE. IT MELTED AND THE CODE IS NOT READ. THANKS
I'love thundercats 80s...liono....panthro 😂😂
Thunder thunder thunder. Thunder cats. Hooooooo
10:10 Hello friend, that resistance of what value is it?
I would like to know aswell
Hi i repair this psu and i dont know the name of the Q9 transistor, c49,zd38,zd39 do you help me?
I need the name of this transistor too
Zd38 y zd39 please
Hey hows it going today i tried to fix an ADP-200ER (for the 1200 series ps4) which has no power the ps4 beeps once the 12V does not kick in, i opened up the power supply and there was alot of dust in it .I cleaned it and checked all the power IC and transistors for shorts i could not find anything short the big fusible resistor was also good . Do u know what could be bad that prevents the 12V from kicking in ?
Possibly bad mosfets. Check in diode mode. Possibly faulty pmic. Possibly small caps blown. Look under scope
thanks for your reply . which pmic are you referring to ? DAP041 ?The funny thing is i just tried it and its started to work . i guess we can call it an intermittent power supply . I'll take a look under the microscope to see if anything is burnt .
Nikesh Gupta you changed the DAP041? And now it works?
If you have Facebook. Find us there. Easier to communicate
Nikesh Gupta you changed the DAP041? And now it works?
If you have Facebook. Find us there. Easier to communicate
No i didnt change anything yet , I will add u to my facebook
Pergunta, como meu PS4 ligar desligar sozinho
I remember mighty mouse, showing ur age my man
in which position put the tester????
also.i was wondering if anybody knows what my multi should read if i test it on my power supply out.of the system but plugged imto the wall ??????
meter
Sir can. Send us here a video that fixing you an hdmi problem?
Nice work...
hola tengo una fuente de ps4 u.slim que anda y a los 15 minuitos se apaga.. probe con otra y anda bien el tema que se caen los 12v que tengo que reemplazar. gracias
What could the potential problem be in my case I am working with the same psu ADP 160er, system turns on loads up just fine until around the 5 minute mark. Then beeps twice simultaneously and system shutdowns? (No warning signs whatsoever)This happened multiple times, remind you the councle I'm working with is clean and quiet, I've checked the psu and cannot fine anything out of the regular? Please Help! Thanks All
motherboard or over heating
well im prettty sure tha roaches fried mine. i done tried swapping out the whole power supply with no luck appqarently i was given another bad one . and i just bought sonic mania and i didnt ger to beat it yet. so now im stuck wondering what to do next. ithink lll ttry the resistor like.you.did.on this video
Muchas gracias,
Looking for that zener diode reference anyone?
Also need this
Also need this please if possible.
Can you give me if you have schamatic
of this
My PS4 model # is CUH-1215A how do I know if it's the ADP-200ER and ADP-200cr Thanks.
Shane Jones ADP-200ER
I was wondering what resistor did you use 10K or what to look for it by
www.mouser.com/ProductDetail/KOA-Speer/MFS1-2DCT52R16R2F?qs=%2fha2pyFadugux5duMxIeSkURl25n9ULqROTKImSPp6EHvE1s%2f%2fKYSqG2UJ2xU%2ffX
can u fix my ps4 pro power supply were to i send it?
What’s R1 resistance ? I look in so many places , everyone says something different ...
No kidding, it's like a deep dark secret. A 5 band resistor with a silver third band is foreign to my knowledge.
16.2 Ohm
Es una resistencia de 0.16r simplemente
Esquematico porfa lo necesito
Waste of time watching. Guy has no clue about troubleshooting or current draw.
Please the Brain ,...share the Zener link in mouser
Part number BZX55C8V2
I don't understand why you are so rough with it! I wouldn't want you working on my consoles.
Wouldn’t wanna either
mighty mouse "saves the day" --Danger Mouse was that weird british cartoon along side banana man (on Nickelodeon in the early 80's). i think the feature film y'all mentioned was maybe "under dog".
kevin Deal lmao. Good to know. You must be born in the 80’s too
What is value of resistor? R111?
16.8O /2.0%
0.16r
its good but not that good u not showing what your meters reading at
thanks bro
wow you are a singer too? Please lets dance newt video!
I watch from Brasil.
RESPECT!
OMG, is this another part from "idiots at work"?
Sir please use a adjustable power source or a simple lamp in row to the power supply to protect the resistor and other parts.
O man, don't spoil it, I'm enjoying this!
Dont talk when your working
Who the fuck are you
basta con questo flussante ogni volta che devi fare una saldatura....
hi all the crap about the cartoons spoils the vid
Kkkkkkkkk
Is the glove to cover prison tattoo's? You have zero respect for what I presume is a customers machine.
Ahahaha ur an idiot
u really fol haaaaa
friend what is the fet that you changed could you give me the number
amigo cual es el fet que cambiaste me podrias brindar el numero
24N60