I work with handicap mobility here in the US as a hobby out of my home garage. I have found that if I turn the scooter on its side and spray the end of the axle like you did with WD40 and let it sit for a few minutes the wheel comes right off. Also, I put a lite coat of grease ON the axles and keyway area to prevent and/or stop the "clicking" that is sometimes heard coming from the back wheels.
Wow, great demo. This is exactly what’s wrong with my maxima XL. Can you tell me approximately how much that repair should be. I doubt I could get the parts here very easily.
Great video and help me troubleshoot a friends Invacare Leo scooter with the same brake assembly and trying to get a replacement and hoping you can help
Great video, especially showing the full job getting it off - tricky last bolt! I have a kymco maxiLFORU and have no resistance showing across the terminals on my electro brake (and diagnostic light flashing 9 times and no drive). Do you reckon I'm on the right lines in changing the brake for a new one? Having trouble getting one so trying to make sure i'm not wasting my time... The microswitch works ok, just no ohms between the 2 terminals
I've Astrid md 4 it was jerkin before it stopped.and 2 lights stasted flashing. I removed the brushes I am writing for them to arrive .6mm x10mmx15mm ?.1 off the brushes springs was broken Thank you for your help
Hi. You and your videos are second to none. I have a problem with a CTM hs740 .code 5 flashes . fitted a new brake 3 months ago . now virtually straight away , not after running for 45minutes, the scooter is really slow ,forwards and backwards. Batteries are good , advice please ,thank you.
Thanks ,but what will that prove ? Not sure I understand . are you saying disconnect the brake from the motor .then test drive the scooter. If full power is achieved, does this tell me that the brake is faulty ? Thank you.
If you check the plastic bit that fits over the motor drive nut, it should turn as well as move around. If you can't turn it with either a bolt head in the hex hole or with a tiny screwdriver in the holes at the edges of the nut, give it a spray with oil or WD40 and work it free. It should then work. It is probably almost seized and that is why the motor is slow. Once it is oiled and back in place, get the wheels off the ground and run the motor at full speed. It may take a while to get speed up as the oil gradually does its work but then it will be ok. No way was I going to replace the unit at around £50 +.
I had my motor out of my scooter to repair broken brushes. After I reassembled it, the brake is not holding on a slope when I stop. Is there a tension screw or something to adjust, or is it a new brake unit needed?
We have a Zero Turn radius 2 motor pride scooter that is displaying the 5 flash motor brake code. Randomly the code flashes and can be reset by moving the freewheel selector levers off and back on. Often this will "fix" the problem, but a few minutes later the same error repeats. I did see a bare wire where the wires pass thru the seat post tube and placed electrical tape around each wire. This seemed to help for a couple of weeks, but has returned. Are there any adjustments to be made in the brake cartridge?
I have a Pride Legend, while I was riding it,it kept going out but I would turn key off & on & it would run again.Then one day it didn't, Lucky I was only 1 mile from home so I pushed it home.All the power was on - lights,horn, everything but it wouldn't go.Can you help me I need it for transportation, going shopping, to the store etc, especially my doctors appointments at the VA hospital,I'm on social security so I can't afford a new one or to get it fixed.would you have any ideas and tell me how to fix it? thx. Gil
Hi Mr Magic. Would you have any idea why on my shoprider scooter the battery shows full, after a minute or two the indicates start to go down, it looses speed, but after releasing the wig wag drive just a few seconds the battery indicator comes back near the full mark but then it happens all again.🤔🤔
check to see if your brake is hot that will cause a current draw... also how old are your batteries ... check all connections to and from the battery including circuit breaker terminals
@@tomjacques4 Hello Mr Magic, I did what you are often saying about batteries, but didn’t know what else to do because of a number of problems arising on the two scooters, ironically they are almost both the same, so bought two batteries but only partially helped on one scooter but didn’t cure all problems, I have replaced the tiller control, that helped, I have ordered two reset units, replaced the speed control and wig wag. The motors are not getting hot at all, only thing I don’t think I have replaced is the control unit, motor, and break unit, so as you can see the Grrrrr’s are in the wind.🤔😊😊
@@tomjacques4 Hi again, the batteries are 12months old I bought new batteries for both shopriders, their voltage reading. Is good , after looking at your video regarding a fault of circuit breakers I ordered two to see if it makes any difference. Would the control box have any thing in it that could be any related problem. I bought them from two different people around 12 months ago, and seems ironic that both scooters have similar related problems. To add to my problems my car has broken twice in two weeks with the Same Electrical problem as the first time. 🥵🥵🤔😊
Buenas tardes, disculpé,tengo un scooter Gogo élite traveller, al encenderlo suena una alarma da5 pitidos, cree usted que sea el mismo problema,?soy de México, gracias
I bought a drive scout 4 new 5 years ago. Only used it about 20 times going to the dr. I’m getting 5 beeps, I brought it in the house from the car I put it in drive and it worked for a minute. I’ve got 26 volts. Opened up the floor plate to check voltage regulator, I’ve got 26 volts on the red and black. When I check the volts coming off the regulator I had some at first when I pulled the forward and reverse handle and it did move only for a short time and it quit. Is there anyway I can know for sure if it’s the brake or the regulator. Thanks in advance and also where I could get the parts
I have learned a lot from your videos. Do you have the name and address for purchasing a brake? I have a 2014 Pride Wrangler Mobility Scoter (PVM600). Thank you
Happy new year. My problem is the wigwam pot ,fast slow . But I also have a noise from rear when it's going on its slow motion once it speeds up again the noise goes.is this all to do with the worn wigwam pot. It's a invacare Orion.Thank you.
hi Tom john here still got that wiring problem now it's gone to not working at all no reverse or forward power is there every thing else working but got a faint buz from where the hooter and hazard sound comes from all I have done is disconnected all the connectors and put them back again then i ended up with this problem getting fed up with it mite get the big hammer out
john p yes as long as you have the space you can increase the distance you can travel. Mind you you will not increase power only distance travelled. You can get 50amp batteries in the same size as 45s.
if im at a customers and the green light flashes, i go online for the manual for that scooter and it tells me why it flashes one, 2, 3, 4, 5 times etc,
Hi. could be a throttle problem with it not being in neutral on power up but it will depend what type of control box you have send me a picture to nithsdale.wheelchairs@btinternet.com
very informative video . many thanks for sharing
I work with handicap mobility here in the US as a hobby out of my home garage. I have found that if I turn the scooter on its side and spray the end of the axle like you did with WD40 and let it sit for a few minutes the wheel comes right off. Also, I put a lite coat of grease ON the axles and keyway area to prevent and/or stop the "clicking" that is sometimes heard coming from the back wheels.
Great video, looks like electric brakes are the must common problem with scooters, 👍👍.
Wow, great demo. This is exactly what’s wrong with my maxima XL. Can you tell me approximately how much that repair should be. I doubt I could get the parts here very easily.
Great troubleshooting videos
Great video and help me troubleshoot a friends Invacare Leo scooter with the same brake assembly and trying to get a replacement and hoping you can help
Hi yep have stock link below
www.nithsdale-wheelchairs.com/prods/347496/invacare-scooters-electric-brakes.html
Wow, it looks like its been used surfing the Nith hahaha. Good video, a tough one for sure.
Great video thankyou
Can you alsof fix electric wheelchairs? Like Permobil and Dietz?
Most power chairs work exactly the same it’s only different hardware that is used
Great video, especially showing the full job getting it off - tricky last bolt! I have a kymco maxiLFORU and have no resistance showing across the terminals on my electro brake (and diagnostic light flashing 9 times and no drive). Do you reckon I'm on the right lines in changing the brake for a new one? Having trouble getting one so trying to make sure i'm not wasting my time... The microswitch works ok, just no ohms between the 2 terminals
Remove the brake and try to drive scooter off road. We have all brakes in stock
I've Astrid md 4 it was jerkin before it stopped.and 2 lights stasted flashing. I removed the brushes I am writing for them to arrive .6mm x10mmx15mm ?.1 off the brushes springs was broken Thank you for your help
Hi. You and your videos are second to none. I have a problem with a CTM hs740 .code 5 flashes . fitted a new brake 3 months ago . now virtually straight away , not after running for 45minutes, the scooter is really slow ,forwards and backwards. Batteries are good , advice please ,thank you.
Remove brake from the motor but still have the wires attached then try again. Be careful as you will have no brakes
Thanks ,but what will that prove ? Not sure I understand . are you saying disconnect the brake from the motor .then test drive the scooter. If full power is achieved, does this tell me that the brake is faulty ? Thank you.
If you check the plastic bit that fits over the motor drive nut, it should turn as well as move around. If you can't turn it with either a bolt head in the hex hole or with a tiny screwdriver in the holes at the edges of the nut, give it a spray with oil or WD40 and work it free. It should then work. It is probably almost seized and that is why the motor is slow. Once it is oiled and back in place, get the wheels off the ground and run the motor at full speed. It may take a while to get speed up as the oil gradually does its work but then it will be ok. No way was I going to replace the unit at around £50 +.
My mobility scooter indicator light is on and power is off .what should I do?
I had my motor out of my scooter to repair broken brushes.
After I reassembled it, the brake is not holding on a slope when I stop.
Is there a tension screw or something to adjust, or is it a new brake unit needed?
Have you forgotten to tighten the nut on the end of the motor ? Or even to fit it.
@@tomjacques4 you are amazing, exactly what the fault was, many thanks from NZ… 😎
Who to replace the floor
why my mobility scooter does not stop when i take my thumb off the throttle
We have a Zero Turn radius 2 motor pride scooter that is displaying the 5 flash motor brake code. Randomly the code flashes and can be reset by moving the freewheel selector levers off and back on. Often this will "fix" the problem, but a few minutes later the same error repeats. I did see a bare wire where the wires pass thru the seat post tube and placed electrical tape around each wire. This seemed to help for a couple of weeks, but has returned. Are there any adjustments to be made in the brake cartridge?
I have a Jazzy. Any idea why pushing forward makes scooter go backwards and backward makes scooter go forward?
Can you repair the motor brake have seacroft just beeps battery seems fine can hear click when pressing throttle
Take the brake off and check to see if the internal disk is moving when you hear the click
@@tomjacques4 thanks for replying the click seems to coming from gearbox side
The we lights go off when you start on driving
What’s the make and model and what light ?
I have a Pride Legend, while I was riding it,it kept going out but I would turn key off & on & it would run again.Then one day it didn't, Lucky I was only 1 mile from home so I pushed it home.All the power was on - lights,horn, everything but it wouldn't go.Can you help me I need it for transportation, going shopping, to the store etc, especially my doctors appointments at the VA hospital,I'm on social security so I can't afford a new one or to get it fixed.would you have any ideas and tell me how to fix it? thx. Gil
Hi Mr Magic. Would you have any idea why on my shoprider scooter the battery shows full, after a minute or two the indicates start to go down, it looses speed, but after releasing the wig wag drive just a few seconds the battery indicator comes back near the full mark but then it happens all again.🤔🤔
check to see if your brake is hot that will cause a current draw... also how old are your batteries ... check all connections to and from the battery including circuit breaker terminals
@@tomjacques4 Hello Mr Magic, I did what you are often saying about batteries, but didn’t know what else to do because of a number of problems arising on the two scooters, ironically they are almost both the same, so bought two batteries but only partially helped on one scooter but didn’t cure all problems, I have replaced the tiller control, that helped, I have ordered two reset units, replaced the speed control and wig wag. The motors are not getting hot at all, only thing I don’t think I have replaced is the control unit, motor, and break unit, so as you can see the Grrrrr’s are in the wind.🤔😊😊
@@tomjacques4 Hi again, the batteries are 12months old I bought new batteries for both shopriders, their voltage reading. Is good , after looking at your video regarding a fault of circuit breakers I ordered two to see if it makes any difference. Would the control box have any thing in it that could be any related problem. I bought them from two different people around 12 months ago, and seems ironic that both scooters have similar related problems. To add to my problems my car has broken twice in two weeks with the Same Electrical problem as the first time. 🥵🥵🤔😊
Buenas tardes, disculpé,tengo un scooter Gogo élite traveller, al encenderlo suena una alarma da5 pitidos, cree usted que sea el mismo problema,?soy de México, gracias
I bought a drive scout 4 new 5 years ago. Only used it about 20 times going to the dr. I’m getting 5 beeps, I brought it in the house from the car I put it in drive and it worked for a minute. I’ve got 26 volts. Opened up the floor plate to check voltage regulator, I’ve got 26 volts on the red and black. When I check the volts coming off the regulator I had some at first when I pulled the forward and reverse handle and it did move only for a short time and it quit. Is there anyway I can know for sure if it’s the brake or the regulator. Thanks in advance and also where I could get the parts
I have learned a lot from your videos. Do you have the name and address for purchasing a brake? I have a 2014 Pride Wrangler Mobility Scoter (PVM600). Thank you
Hi send me the serial number please my contact details are nithsdale.wheelchairs@btinternet.com
Hi thanks for sending over some pictures... our suppliers are on holiday until the 4th of Jan ... i will get back to you then
Happy new year. My problem is the wigwam pot ,fast slow . But I also have a noise from rear when it's going on its slow motion once it speeds up again the noise goes.is this all to do with the worn wigwam pot. It's a invacare Orion.Thank you.
Hello! I have a Shoprider scooter and it always beeps but it doesn't start. Why?
hi Tom john here still got that wiring problem now it's gone to not working at all no reverse or forward power is there every thing else working but got a faint buz from where the hooter and hazard sound comes from all I have done is disconnected all the connectors and put them back again then i ended up with this problem getting fed up with it mite get the big hammer out
Lol you been out in the rain salinas like you have wires crossed.
Hello i have a tzora titan and have a 7 flash code we change the pcb and operation lever, and i have the same 7 flash
Hi what type of controller do you have
@@tomjacques4 hi mi friend a s controller
@@joshepangulo8291 an S drive ?
@@tomjacques4 yes sorry s drive
@@joshepangulo8291 ok what Pcb did you replace and I recon you replaced the throttle pot that is attached to the lever
Hi,my mobility scooter as 45ah batteries can I go any bigger for extra strength and mileage thankyou,
john p yes as long as you have the space you can increase the distance you can travel. Mind you you will not increase power only distance travelled. You can get 50amp batteries in the same size as 45s.
Nithsdale Wheelchairs V could I go any higher than 50ah Andrew would sooner ask for your advice before hand,cheers Andrew
john p as long as there is plenty if room for a larger capacity battery yes
Hi, is there a single manual brake on a TGA Breeze ? On one wheel ? ...........is it needed ?
The manual brake is only used when it’s in manual mode When you push it
We could do with a wee video about the speed adjuster?
Andrew mcbride I have done a few videos on the throttle pot or is it the speed pot on the dash board that you would like.
if im at a customers and the green light flashes, i go online for the manual for that scooter and it tells me why it flashes one, 2, 3, 4, 5 times etc,
ian may hi should do ian.
Hi. If a woodruff key is put in backwards. Would the mobility scooter still drive.... thanks
Karl Sutton backwards ? As long as it’s back in it’s ok
i have TGA VITA MIDI with Error code 9 any ideas what this is as I cannot find an error code sheet anywhere
christopher stearman hi 9 flashes usually is the solenoid brake issue.
Optimus 2 Shoprider Brakes
Hi how can I help you
my wife scooter charger is telling me the scooter is charged when its not connected and when its is it saying the scooter is charge when its dead flat
No power in scooter
Check you fuses or circuit breaker
Hi I followed your video is clear and very interested I would like to ask you question on my mobility scooter I have 7 flash light what it is?
Hi. could be a throttle problem with it not being in neutral on power up but it will depend what type of control box you have send me a picture to nithsdale.wheelchairs@btinternet.com