xTOOL LASER ENCLOSURE
HTML-код
- Опубликовано: 26 авг 2024
- #xToolD1Pro #xTool #laserengraver
Discount code TG10 : 10% off - To Purchase - www.xtool.com/...
Discount code TG10 : 10% off for D1 Pro, F1, M1 and their bundles
www.xtool.com/...
This is the @xToollaser Laser enclosure that is designed for the D1 and D1 Pro. However, given its size it should be able to accommodate other laser engravers as well.
Size is 310*610*625mm.
* Suitable for xTool D1/D1 Pro and other laser engraving machines
* Exhaust Fan with hose
* Foldable & Most Portable Enclosure
* Fire-retardant
* Efficient Ventilation
* Protect your safety & health away from smog, noise, dust as well as
* pungent odor
Purchase Here -
www.xtool.com/...
Etsy Spoilboard \ Wasteboard -
www.etsy.com/l...
3 Inch Duct Fan
amzn.to/3QCkSf3
Portable Air Conditioner Window Seal Plates Kit, Vertical AC Window Unit
amzn.to/3PnIX7L
4 Inches Louvered Dryer Vent Cover
amzn.to/3dpusD5
Honeycomb Laser bed -
www.comgrow.co...
Thangs.com xTool Tie Downs -
thangs.com/des...
#Polymaker Silk Purple Filament -
polymaker.com/
#Lightburn Software
lightburnsoftw...
Disclaimer - This is an instructional video only - I assume no responsibility if you do not become a pro after watching this video. This video is for learning purposes only, you are following the steps in this video at your own risk!
/ tripodsgarage
/ tripodsgarage
/ tripodsgarage
Thanks for watching - Please Like and Subscribe!
Tags
Kywoo, Tycoon, Tycoon Max, Tycoon Slim, CR6-SE, CR6SE, 32-Bit Control Board, TMC2209 Stepper Motor Driver, 3D Printer, 3D Printing, CR-10, CR-10s, Ender 3, Ender 3Pro, Ender 5 Pro, Ender 5, creality silent board, silent board, BIRGTREETECH, SKR CR6V1.0 #tycoon #tycoonslim #tycoonmax, ATOMSTACK A5, #ATOMSTACK #ortur #xtool #laserbox #thangs #thangs.com
I found that even this one (neverest RV-B 4 Inch Inline Fan 176 CFM) from Amazon is just barely enough to keep the smoke at bay. The garage still gets a hint of scorched wood. The previous exhaust blower I tried was "rated" at 195cfm, but didn't come close to keeping a negative pressure in my enclosure.
I watched, and I like. Thanks John... getting one of these for my studio. I already have the external blower to hook up instead of the PC fan included!
It is a nice enclosure. Thanks for watching and commenting 👍
Typical that all companies start selling laser enclosures after I spent a weekend building my own 😂 I use a similar fan set up as you fitted to take the smoke etc out and it works much better. Great content as always buddy
I DIY when I have more time on my hands than $$ I can throw at a project. My "enclosure" is made from cardboard box pieces and packing tape to hold it together (I'll make a better one eventually). Not worried about it since I *never* leave the laser unattended when running a job.
Seems like a good option. I am concerned about eye safety with these types of normally "open" lasers. Based on your video review it sounds like you still wouldn't trust looking at the laser unless you have the goggles on. With my Glowforge, I am able to look at the laser cutting just fine without any worry but that is also a 5K+ machine. I wonder if there is a good option for a "safe" viewing enclosure? That is something I would be interested in.
I should have been more clear in my video why I still suggest safety glasses. The viewing window is a flexible plastic material, with no certified markings. Nor, does it say anything on their website. Without knowing, I am not going to put myself at risk. With that being said, I don’t know if any manufacturer actually has that certification stamp on their viewing window.
John, looks like it would be very useful for an engraver that was in a house and had a vent access point. I'm confused, did the added fan make a enough difference to purchase? Didn't see any link for the auxiliary fan
Hello David,
Yeah, the enclosure it really nice! It is really hard to tell if the added fan made a difference. The PC fan caused air to be pushed back into the enclosure. This caused turbulence inside the enclosure. I really couldn't tell how much smoke was escaping. I having the other blower is better because it doesn't cause this. However, the best I can tell the PC fan still works. Hope that answers your question. Also the links are now in the video, I was still adding them.
@@TripodsGarage Thanks for adding the listing on the fan. It is on sale now for just about $40
@@woodwaker1 of course now it is on sale 😂😂
@@TripodsGarage That's because of your legend.
What table did you use to host the laser engraver and enclosure? Trying to look for a big enough but not too big of a table for it.
How are you fitting a 3in diameter hose to a 5in diameter window seal vent?
The enclosure does not keep the smoke smell out very well/I am running it using the small enclosure fan and 4in inline fan, still smells of smoke in the house
What size of exhaust tub is that 3inch or 4inch thank you for your time
what is the base that you have the stool on? an how do I get one?
Can you let me know the time in the video?
at 1:12-1:15. Is the wooden board something that you made to set the honeycomb cutting board on and the xTool unit on. If it is something that you made I would pay you to make one up for me as well. I really like the X/Y axis lines that you put on the board as well as the feet cups.
@@randygiboney6368 Yeah, I made the board and 3d printed the feet cups - It is in this video ruclips.net/video/JVfmPDRFlQY/видео.htmlsi=yhN6mFTo0DSWFa2s