I survived the experience in good form. It wasn't as difficult as you might think. Some times it looks harder when you are taking care not to damage the tile itself and the surrounding tiles.
I appreciate the feedback. Let me know if you have any questions. you can email me at d-morrison@groutrx.com and we can have a more direct conversation if you find anything not covered in the video.
Much appreciated. I have my favorite channels as well, Food Wishes and Middle Eats are among them. Let me know if you have any questions. I'm happy to help people out.
@@groutrx1415 did my tiles yesterday and followed your advice, ESPECIALLY with the sponge. It doesn’t take a lot to make that floor wet and the grout loose. Thank you again for this helpful and straightforward video
My husband and I were going to rent out the big machine(sorry i dont know the name it) at home depot it would have been over $200 the space is less than 300 sq ft .. this will save us money even if it takes me all day thank you!
Can you please clarify what you said at 0:48? You were explaining why it could be loose, one reason was that the tile might not have been adhered properly but the second reason you said wasn't clear as the noise from the tool made it hard to hear.
There are actually many reasons why grout cracks. The tile may not be adhered properly due to: 1. improperly mixed thinset 2. backs of tile were not wiped clean of dust 3. the back the the tile was not coated to till the cells The substrate may be improperly installed: 1. Was nailed down instead of screws 2. screws are not frequent enough (should be every 6") 3. seam tape was not installed 4. Backer board was not wiped clean prior to thinset application Finally, the subfloor, the plywood directly on top of the joists, should be no less than 3/4" thick and the joists should be 16" on center. If there are structural issues, this can cause the grout to crack as well.
I have three loose tiles. I have two questions: 1. My tiles are directly on wood. How much of old thin set do I need to get off? I can use a floor scraper and it all comes off pretty much. Do I need to get it down to bare wood again? 2. How does one level the tile to keep them all flat, no high/low spots? IN this video, they used cardboard. Any ideas? I am afraid of replacing the three and then only to have my wife stub her toe afterwards from a high spot lol.
The more thinset you get off, the better. I find the Carbide Grit Triangular Grinding Rasp For Oscillating Multi-Tools works best to get thinset off. See the video here: ruclips.net/video/08ULAcjbRMM/видео.html Some modified thin sets can be used on plywood, but most often times I find they eventually come loose from the wood, especially if the floors are mopped and water soaks into the grout causing the wood underlayment to expand and contract. I usually use Latapoxy 300 if ever I find myself adhering tile to wood. The tiles will never come loose. This is messy stuff though. Be sure to wear gloves and clean up well with warm water www.flooranddecor.com/laticrete-installation-materials/laticrete-latapoxy-300-adhesive-100894849.html In terms of getting the tiles to set evenly, I would recommend putting more thinset in lower areas and do it by feel. Be sure to clear out the grout lines of any excess thinset.
This has just happened to me. Iam in the middle of remodeling my bathroom and I have put floor tiles down all the room is set apart from four near the door they where cracking when walking on them and realised that's where the adhesive has dried out when I have laid it and it hasn't stuck well to the tile. So now I have lifted them scraping the floor to then reapplying them to the floor.
I wish you could chosen an easier tile to take out. It’s hard to watch you struggle so much however I’m glad you got that tile out! What a bear.
I survived the experience in good form. It wasn't as difficult as you might think. Some times it looks harder when you are taking care not to damage the tile itself and the surrounding tiles.
Excellent demo.This is exactly what I'm after today. Well done !
I appreciate the feedback. Let me know if you have any questions. you can email me at d-morrison@groutrx.com and we can have a more direct conversation if you find anything not covered in the video.
Thanks! I'm already feeling better about a successful repair!
Message me with any questions.
I love RUclips university and I love this video. Thank you
Much appreciated. I have my favorite channels as well, Food Wishes and Middle Eats are among them. Let me know if you have any questions. I'm happy to help people out.
@@groutrx1415 did my tiles yesterday and followed your advice, ESPECIALLY with the sponge. It doesn’t take a lot to make that floor wet and the grout loose. Thank you again for this helpful and straightforward video
My husband and I were going to rent out the big machine(sorry i dont know the name it) at home depot it would have been over $200 the space is less than 300 sq ft .. this will save us money even if it takes me all day thank you!
Hope this works out well for you. Let me know if you have any questions.
Can you please clarify what you said at 0:48? You were explaining why it could be loose, one reason was that the tile might not have been adhered properly but the second reason you said wasn't clear as the noise from the tool made it hard to hear.
There are actually many reasons why grout cracks. The tile may not be adhered properly due to:
1. improperly mixed thinset
2. backs of tile were not wiped clean of dust
3. the back the the tile was not coated to till the cells
The substrate may be improperly installed:
1. Was nailed down instead of screws
2. screws are not frequent enough (should be every 6")
3. seam tape was not installed
4. Backer board was not wiped clean prior to thinset application
Finally, the subfloor, the plywood directly on top of the joists, should be no less than 3/4" thick and the joists should be 16" on center. If there are structural issues, this can cause the grout to crack as well.
Thank you!
Glad you found this helpful!
I have three loose tiles. I have two questions: 1. My tiles are directly on wood. How much of old thin set do I need to get off? I can use a floor scraper and it all comes off pretty much. Do I need to get it down to bare wood again?
2. How does one level the tile to keep them all flat, no high/low spots? IN this video, they used cardboard. Any ideas? I am afraid of replacing the three and then only to have my wife stub her toe afterwards from a high spot lol.
The more thinset you get off, the better. I find the Carbide Grit Triangular Grinding Rasp For Oscillating Multi-Tools works best to get thinset off. See the video here:
ruclips.net/video/08ULAcjbRMM/видео.html
Some modified thin sets can be used on plywood, but most often times I find they eventually come loose from the wood, especially if the floors are mopped and water soaks into the grout causing the wood underlayment to expand and contract. I usually use Latapoxy 300 if ever I find myself adhering tile to wood. The tiles will never come loose. This is messy stuff though. Be sure to wear gloves and clean up well with warm water
www.flooranddecor.com/laticrete-installation-materials/laticrete-latapoxy-300-adhesive-100894849.html
In terms of getting the tiles to set evenly, I would recommend putting more thinset in lower areas and do it by feel. Be sure to clear out the grout lines of any excess thinset.
I think the thin set was dried out and had skinned over when the tile was laid.
That's a possibility.
This has just happened to me. Iam in the middle of remodeling my bathroom and I have put floor tiles down all the room is set apart from four near the door they where cracking when walking on them and realised that's where the adhesive has dried out when I have laid it and it hasn't stuck well to the tile. So now I have lifted them scraping the floor to then reapplying them to the floor.
Thin set the floor and then back butter the tile with thin set, it’s cheap insurance against this issue
Thanks for the feedback. We cover this in part 4 of the series.
Talking and scraping at the same time not good for us trying to listen to you talk
Thank you for the feedback.