Ik leg tegels al 21 jaren, dit methode had ik vorig jaar uitgeprobeerd maar voor mij is niet handig en juist dubbel werk. Succes voor degene die deze methode fijn vinden..
Во первых технология давно известна, только зачищать швы болгаркой это куча сколов, есть специальный инструмент. Во вторых шарик у нас уже лет как 5 заменили зажигалкой cricket там танец овальный и идеально подходит под мелкие швы, в 3-х лунка которая получается от шарика или любого другого инструмента смотрится красиво на стенах, но вот на полу это очень большой недостаток т.к. там скапливается грязь и ее от туда очень неудобна вычищать, для пола только прямые швы и никаких ямок😊
Да ещё и белая затирка на пол как-то не очень подходит - вся грязь будет видна на ней + думаю со временем белизна уйдет по той же причине. А вообще, как по мне, лучше один раз запариться с эпоксидной затиркой и забыть о межплиточных швах.
100% agreed, I work in IT so an entirely unrelated field, but I have tiled for 35 minutes and know this is utter rubbish. Frankly, anyone with an IQ over 35 even would know this is absolutely the wrong way to do grout. Thanks for calling out the bs.
OK, Luigi, do a video for us and show us how good you are. Frankly, IMO, you comment was not necessary, and it was just insulting. A lot us guys here are very grateful to see this demo.
@@sunriseboy4837 all I am reading is "you hurt me, you insulted me, others said nice things about this video and they are grateful, your comment is superfluous" easy does it! the clickbait title had to be redimensioned and I took on that task
@@sunriseboy4837please don't use this as a demo. If customers are paying you and you end up doing this, you will be screwing them over. If you can't tell that the grout is WAY too wet, then I'm afraid you need to start all over and be retrained.
It takes a skilled hand to take a chance like that with a grinder. I’ve done this before with a lot of success, but one slip and the floor is done for make sure there’s a spare tile if you decide to use this method. On a different note, what kind of grout float is that?
@@arnoflyOnWeb I tried an angle grinder also. It can be faster but I would accidentally nick the side of a cross tile (“T”) from time to time and it’s harder to control the depth of cut.
Super Arbeit. Wir sind nach dem Tod meiner Mutter in mein Elternhaus eingezogen. Im Gäste WC waren die Fugen zwischen den weißen Bodenfliesen ursprünglich lichtgrau. Da ihre Putzfrau scheinbar mehr zu ihrer Unterhaltung einmal wöchentlich erschien, wurden die Fugen allmählich unansehnlich schwarz. Ich dachte zunächst auch an deren Erneuerung, habe mir aber dann ein Herz genommen und bin die Sache mit Kunststoffbürste und Scheuermilch angegangen. Jetzt strahlen die Fugen wieder in schönem Lichtgrau. Trotzdem ein tolles hilfreiches Video.
Looks nice, but adding too much water to grout weakens the mix (similar to concrete) and won't last too long, unfortunately. Would like to see what that floor looks like a few months later.
who told you too much water weakens concrete? unless you put 1gram on concrete in a 1000 litres on water lol, concrete can, and does, set (completely) whilst under water, and is still extremely strong, so how much is too much water if it can set under water?
I'm with you, grout to loose, I've never had to use ball-bearings on any of my grout joints, just trowel then wash, I don't get it?? 35yrs in the tile trade
@@dannythorpe1425 When excess water creates greater spaces between aggregate materials, the voids fill with air after the moisture evaporates. The resulting inadequate compaction reduces the concrete's strength. Concrete with trapped air levels as little as 10 percent experiences reductions in strength of up to 40 percent.
@Russ S that's not from too much water, that's from adding aggregate. Concrete will fully set underwater. Also adding aggregate and preparing the job properly won't have that effect. If the aggregate has no where to move the water won't displace it. Aggregate is not concrete, water doesn't weaken concrete.
You have to be very careful not to damage the tiles with the angle grinder. The step with the ball you can leave out. No professional does that because you go over the joints with the rubber plate and after a little drying you come back with a sponge - as shown. But you have to work diagonal over the joints NOT along the joints. This way you'll get the beautiful shape of the joints automatically. Imagine all the professionals sit there and play with a ball while making hundreds of square metres of tile laying - five head 😂
Для профессионалов эта идея наверное не подходит, но я в восторге от этой идеи! Метлах на кухне уже расшатался. Клей высох. Мастер так и сказал: Снимать и снова укладывать. А это сколько проблем! Очистка и прочее. После этого видео я сама справлюсь. Благодарю Автора этого видео!
@@krasnonosov51 а ты знаешь какое значение слова на грузинском твой ник ( чатланин?)что-то вроде проститут или точнее пидор. 😁. Так что подумай.чатлак звучит правильно.
@@БогатыйПролетарий Вы, наверно, на него наступили. Он вполне мог продавиться внутрь подошвы... Когда обувь износится поищите его шилом в маленьких отверстиях, он обязательно выкатится, если не запропастился куда ни буль...
First mistake is White grout on a floor, i bet that new grout went dirty grey within a month, Second, although using a grinder to take the old grout out is nice and quick, you only have to just touch the tile and you are taking off the glaze / chipping the tile. Whats with the ball bearing ??? you then squeegee the floor after running the bearing over the grout line putting the grout back into the grout line, then you wet sponge it again, so what profile there was you created by using the bearing as a molding tool has well and truly gone. What a pointless waste of time. Also the grout was far to watery. Please don't use this a guide for re grouting a floor. There must be lots of videos on here that show the correct way to do the job properly. Rant over. Nice grout float though.
@@ginoginetti Grey , all day long. There are many shades of grey to choose from. Black at a push but it will stain all your grouting tools and clean up takes so much longer.
Good technique and quite easy for filling up the joints between the tiles after cleaning up the old joists which have become dirty and weak as well.white cement slurry is deliberately chosen to make the video clip more clear to understand the workmanship which is absolutely perfect. Cutter is used to clear the old joints of cement quickly. Slight chipping of corners is covered with cement slurry after drying and rather joints are more tough as the corners are free of glaze and have become rough.
@yuvrajmehta7744 Indeed poignant, well worded and relevant comment. Some people don't realize that ceramics, cement and even gypsum plaster are but a few of materials which have been formulated and modified in numerous ways by either trial and error or by experts who understand how to use existing products, One thing that came to mind is Expansion cement or anchoring cement.
Id like to think this “section at a time” is just for demonstration purposes only not so much a technique. What’s the proper way of going by this in your opinion?
@@juanc.9735 Just every standard grouting technique recommended by the manufacturers. They are usually written somewhere on a flyer bundled to the grout. The same goes for everything on a construction site. Idk, mixing concrete, routing the cables, HVAC installations. This may differ in some states - so you should be aware of it when buying some fancy shit on the Internet. Most European appliances would be useless in the USA, so all the tips for EU installations.
Grout is not to be mixed at that consistency. It will likely crack or have pin holes. Also i don’t believe it would bond nearly as good as traditional method of pressing grout into the joints and wiping with a rung out sponge. But looks like a great way to shallow the grout joints tho 😂
Agreed. There is no guarantee that the grout actually ran deep into the gaps. Personally, I push grout in deep as I go, scooping off access, and working in, continuously.
If I need to repair grout that cracked/broke, assuming I don't want to pull up the tile, I'll use TEC AccuColor sanded siliconized acrylic latex caulk. Presumably it has flex as well as adhesion so it won't crack again.
I am a Jack of all trades and master of only a couple, but I must say this video was excellent. When you plan out a video of instruction this well, no words are needed. Well done sir!
Perché nn fa vedere la stuccatura da vicino?? Così si noteranno le scheggiature delle piastrelle dovute al flex col disco diamantato. Esisto soluzioni meno invasive.
Шов пропилен глубоко, а новый цемент пролит лишь по поверхности, а не на всю глубину, что приведёт к провалам после эксплуатации. Шарик сформировал паз, а затем полутёрком его снова испохабили. В общем, халтура, а не работа.
Had to grind out a bad grout job due to caracks and discoloration. The customer had applied some kind of sealant that created a top layer like rock. Did the kitchen, foyer, hallway and bathroom, truly a nightmare job. In the end the customer was thrilled, no ball bearings were used.
В следующем видео ждём засекреченную технологию великих рукож.. пов вселенной, как можно сделать 5ти минутную работу за 24 часа! 🤔 Действительно - уникальные технологии))
Didn't that wheel say "wet cutting only"? Can we assume that was nonsanded grout? Doesn't mixing grout that thin compromise its strength and durability?
Yes, that was my understanding, the grout is there as a bonding and sealing of the joints. As an experiment - - I would like to see a "plan view" showing two tiles and the now-supposed protection
High speed grinder on grout line with one hand, if that grinder gets away its gonna hurt. Maybe use a slower tool. Also what's the point of the metal ball?
Gostei muito da sua explicação, sou mulher, mas as vezes faço alguma coisa de pedreiro, aprendi o básico pq meu pai era esse profissional. Também pq posso fazer, não precisar pagar ou ficar esperando alguém fazer. Também fazer trabalhos artesanais como vasos de cimento, fontes, aquário etc. Obrigada por passar sua sabedoria
Don't want to be negative, but I spent most of my working life in the flooring business and all of my crews used the grinder/vacuum combo, and the ball bearing thing was cute but the same concept as the gadgets they sell for smoothing out caulk. I'm not sure what you thought was the new technique? Regardless, well made video and it may help out some diyer or homeowner, assuming they are experienced with using a grinder freestyle like that. You can make a mess of the tile if not. But again nicely done.
"assuming they are experienced with using a grinder freestyle like that." Yeah, I was looking at that and I was thinking that I would be making a mess of the tiles. The only way I would bother with this is if I were trying to remove the tiles and keep them for myself.
It's a lot of work man I just found epoxy and re- colored my groutand spend 10 years and last and it looks beautiful and it doesn't stain because it truly truly seals
Risky using a cutting or grinding wheel, the slightest touch on the edge of the tiles could chip the tile edges and whilst pouring the grout in might look good initially I would expect the excess water to cause cracking and shrinkage as well as weak/soft grouting, finally I don't get the point of the bearing if you're going to run over it again after whilst still wet.
Caramba! cada dia eu aprendo alguma coisa diferente. Essa do aspirador de pó, a colocação do rejunte, o uso da esfera para dar acabamento. Genial viu! Precisava gravar isso pra não esquecer. Obrigado amigo!
Pega aí uma residência de +ou- uns 50m² pra substituir o rejunte, use a esmerilhadeira com uma só mão, aspirador na outra e, claro "confortavelmente" de joelhos! 😂
Right after the grout is se and dry between the tiles, why aren't the tiles and grout both sealed against discoloration using some kind of polyurethane like we do for wooden floors? I don't wanna spend significant time cleaning when not necessary. I'd rather leave the grout a dark color and make future stains a part of them permanently (as not to draw attention to them.)
Woah. So they now make these grout strips and one can just place those instead of grout. It definitely stays secure for many years but in the case it needs to be switched it’s a strip that you can pull out!
I don't get why you have to furrow the grout anyway. That just gives a place for the dirt and grime to go and build up. Why not have the grout level with the top of the tile. So much easier to keep clean. Someone please explain the need to furrow the grout.
I am a builder and I can say there is absolutely no reason to do so, in fact it creates a void for water to sit in only to slowly disperse to the substrate in wet areas, it’s also a great to create lipping if the tiles are slightly out of level as laid.
you must be a builder from spain ,thailand, or usa, who dont know, that the furrow have to be in level with the tile edge, and the tile edge are bent, slightly down. THIS is the right way to do it. if you lay the furrow over the edge, which is glazed, it will loosen over time.
It seems to people don't like the videos because he takes extra steps. That may not be necessary for others, but the one thing that I do see Benefit In ,is the organization and clean up You may or may not have to do if you follow his steps
This is not the way to fix dirty grout. FYI. You can mix even amounts of swimming pool acid and water. Soak the floor so the tile and grout are both covered in the acid water solution. Let it sit for 20 to 30 minutes and shop vac the floors. Don't scrub. Just vac. The acid will release all impurities/ dirt from the grout. I worked for a very Greek tile layer when I was young. He offered the cleaning service to people he knew couldn't afford to retile their floors. Great guy. This method works 100 percent of the time to clean grout. After you have cleaned it , take Murphys oil soap and seal your grout lines.
The grout mix is too loose .It needs to be tighter because just like concrete mix ,when the mix is too loose ,,then the finished grout will be weak.That means it will more than likely crack and then pop out of the joints especially if there is any deflection in your floor. You have to stiffen the floor with 3/4 plywood sub floor and stiffen grout mixture by not adding too much water. You should never be able to "pour" your grout. Much too loose.
I'm not a professional, but I've done several tile installs for myself. The grout is unusually liquid in this video (lots of water) and since, I as believe tile grouts (at least, sanded grouts) are basically a Portland cement base mixture, how is the hardness and durability after hardening and drying? I wonder about its durability.
Do you know that God has created a way for you to receive mercy and experience freedom in Jesus? And its love for you - so that you have eternal life and forgiveness in Jesus! God, to fellowship with you, gave His Son as an atoning sacrifice. Jesus has paid for you to save you from eternal condemnation because of sin. But this only applies for those who are willing to repent and accept the Lord Jesus in their lives! Repent I beg you, and desire Christ above all else! Love him and follow him to the end, not you you will regret it Would you totally give your life to Jesus Christ and accept him as your personal Lord and Savior?
Es evidente que tiene un muy buen pulso. No creo que astille baldosas ¿Ven como se hunde el disco de corte? Creo que ocurre porque el suelo de apoyo de la baldosa es demasiado débil en algunas partes. El disco se hunde sin que se ejerza una gran presión. Idea: un accesorio unido a al cuerpo de la herramienta y que reemplace a la mano que sostiene la manguera permitiría agarrar la cortadora con ambas manos. Ganaría mayor seguridad para evitar accidentes y mayor firmeza para cortar y evitar posibles rayones en las baldosas.
Bonjour, très bonne technique. Une autre technique que j'utilise pour tout les joints silicone ou autre c'est d'utiliser l'arrière de la cartouche de silicone pour retirer le surplus. Ça fait un joint parfait.
A buddy of mine use to let the grout set up for a little bit so it was just a little moist, not wet, then take the end of a broom handle or any wooden handle and run it down the grout line the same as this.
У него швы довольно широкие 3-4 мм, сколы могут появится только если болгарку уведёт в сторону. Но у него остаётся старая затирка по краю плитки, которая портит весь внешний вид шва.
Jak się chłopu nudzi i ma sracz na 6 m2, to ma czas na takie zabawy. Inna sprawa, że to jest robota zrobiona po chuju, bo między płytkami będzie się brud gromadzić.
ДА ОН СМЕЁТСЯ НАД НАМИ! Быстрое движении камеры (и предметов) создаёт настроение непринуждённости. Медленное - наоборот напрягает, кажется, что сейчас что-то вот-вот может произойти. Но ничего не происходит...
This would be harder to do with the new tile ready pans and kerdi foam pans. You would have cut the water proofing barrier and the pan would then leak.
Что вы там курите парни? На плитке хорошего качества и если клал спец - зафугуется ровно без этого идиотизма, а если плитка некондиция какие нах шарики?
Ok, for who say this takes forever, yes, but I’ve got a tool that can use on regular grout (mixed to consistency that us tilers like and use, imo that is) and then just dip correct size “ball end” in water for some gliding agent to tool grout joints. Ya do this after 1st wash and before final buffing stage. Does add an extra step; so does add time, and imo, if can do great job with joints and being consistent w/ everything…..really don’t need to use, even if doing a regrout. Is cool to watch though, and see. Maybe for a patch repair or something, but not gonna do for a 10k floor laying down using tile, as yeah, money ppl aren’t gonna like those extra hrs 😂
Kiedyś w 80-tych latach do fugowania używało się tylko białego cementu i ta metoda była powszechna. Różnica polegała na tym ,że do nakładania używało się packi z styropianu a przeżynało fugi odpowiednio zaostrzonym patyczkiem. Nihil novi...
Не укладываю плитку 30 лет, но слышал ещё лет 20 назад, что так же плиточники проходили закруглённым торцом зажигалки по швам. Смысл тот же, выходит так же.
@@byenzer5101 nein man. Wenn der Kunde einen Wunsch hat, dann wird erfüllt, egal ob man das sauber bekommt oder nicht. Es gibt Menschen die wollen es nicht gereinigt haben sondern neu! Schonmal daran gedacht?
Ik leg tegels al 21 jaren, dit methode had ik vorig jaar uitgeprobeerd maar voor mij is niet handig en juist dubbel werk.
Succes voor degene die deze methode fijn vinden..
Во первых технология давно известна, только зачищать швы болгаркой это куча сколов, есть специальный инструмент. Во вторых шарик у нас уже лет как 5 заменили зажигалкой cricket там танец овальный и идеально подходит под мелкие швы, в 3-х лунка которая получается от шарика или любого другого инструмента смотрится красиво на стенах, но вот на полу это очень большой недостаток т.к. там скапливается грязь и ее от туда очень неудобна вычищать, для пола только прямые швы и никаких ямок😊
Особенно, когда того пола 200м2. и плитка кривая.
Всё верно
Да ещё и белая затирка на пол как-то не очень подходит - вся грязь будет видна на ней + думаю со временем белизна уйдет по той же причине. А вообще, как по мне, лучше один раз запариться с эпоксидной затиркой и забыть о межплиточных швах.
@@MelnikovValentinкрасава, все по делу
Зажигалку надо взять на заметку, все время использовал кусок уличного UTP для формирования швов.
4:14 You can see all the damaged edges of the tiles from the angle grinder.
Nah, man. That's the new look everyone is going for. Geeze. 🙄
Loved the video! I feel so much better now about my grout job, at least i didn't do it like this guy!
I’ve been tiling for over 26 years and this is absolutely something straight out of a comic book ..!!!
Is it like. Squeeze bag idea or something?
"ma'am, if it's alright we're probably going to be here for the rest of the month so we can finish grouting this."
@@hulkhuggett0
Anyone who has tiled for 35 years would know this is absolutely the wrong way to do grout. What a colossal waste of time.
Ma questo video e di assoluta denuncia. Quanto costa un lavoro del genere? È assunto immediatamente se lo svolge a 2€ al metro quadro m2
100% agreed, I work in IT so an entirely unrelated field, but I have tiled for 35 minutes and know this is utter rubbish. Frankly, anyone with an IQ over 35 even would know this is absolutely the wrong way to do grout. Thanks for calling out the bs.
This is one of the stupid ways that i ever seen on yt...!
It's like reinventing the wheel using squares..
@@jamIam6548
You can do that? 😂😂😂
you laid tiles for 30 years and you are still skilled like one that laid tiles for 2 weeks
OK, Luigi, do a video for us and show us how good you are.
Frankly, IMO, you comment was not necessary, and it was just insulting.
A lot us guys here are very grateful to see this demo.
@@sunriseboy4837 all I am reading is "you hurt me, you insulted me, others said nice things about this video and they are grateful, your comment is superfluous"
easy does it! the clickbait title had to be redimensioned and I took on that task
@@luigicirelli2583 Better English would have been helpful.
@@sunriseboy4837 you are not making any sense
@@sunriseboy4837please don't use this as a demo. If customers are paying you and you end up doing this, you will be screwing them over. If you can't tell that the grout is WAY too wet, then I'm afraid you need to start all over and be retrained.
It takes a skilled hand to take a chance like that with a grinder. I’ve done this before with a lot of success, but one slip and the floor is done for make sure there’s a spare tile if you decide to use this method.
On a different note, what kind of grout float is that?
ever find out what grout float that is??
A grout blade on an oscillating saw also works well to remove grout and is easier to control the depth and cut than an angle grinder.
But angle grinder is very faster (and harder to do a good job). I tried both methods.
I hope they don't have undertile heating! That deep plunge near the start would have destroyed it.
@@arnoflyOnWeb I tried an angle grinder also. It can be faster but I would accidentally nick the side of a cross tile (“T”) from time to time and it’s harder to control the depth of cut.
Aqui no Brasil temos a Saw Marble from Makita
I bet you learning to do tile all on your own!
Always use knee pads when kneeling on a hard floor. (I learnt that the hard way). Thanks for sharing !
What was so special about using the ball bearing?
@@chunkymonkey55555 Try using a basketball, it doesn't work as well.
@@Esuper1 Lol I do not know what I did to offend you into saying that Sir,
@@chunkymonkey55555the ball bearing just set the grout at the desired height relative to the tile edges
I was thinking the same. It looks like he has knee pads on but he's not using them to protect his knees. Strange.
What’s most impressive is this guys is recording himself doing this
Super Arbeit. Wir sind nach dem Tod meiner Mutter in mein Elternhaus eingezogen. Im Gäste WC waren die Fugen zwischen den weißen Bodenfliesen ursprünglich lichtgrau. Da ihre Putzfrau scheinbar mehr zu ihrer Unterhaltung einmal wöchentlich erschien, wurden die Fugen allmählich unansehnlich schwarz. Ich dachte zunächst auch an deren Erneuerung, habe mir aber dann ein Herz genommen und bin die Sache mit Kunststoffbürste und Scheuermilch angegangen. Jetzt strahlen die Fugen wieder in schönem Lichtgrau. Trotzdem ein tolles hilfreiches Video.
Säuregel zum absäuern von Betonflächen und eine Zahnbürste und etwas Wasser und die Fugen strahlen wieder wie am ersten Tag !!! 👌
Looks nice, but adding too much water to grout weakens the mix (similar to concrete) and won't last too long, unfortunately. Would like to see what that floor looks like a few months later.
На верно бухтел плитка и пополнили под плитку
who told you too much water weakens concrete? unless you put 1gram on concrete in a 1000 litres on water lol, concrete can, and does, set (completely) whilst under water, and is still extremely strong, so how much is too much water if it can set under water?
I'm with you, grout to loose, I've never had to use ball-bearings on any of my grout joints, just trowel then wash, I don't get it?? 35yrs in the tile trade
@@dannythorpe1425 When excess water creates greater spaces between aggregate materials, the voids fill with air after the moisture evaporates. The resulting inadequate compaction reduces the concrete's strength. Concrete with trapped air levels as little as 10 percent experiences reductions in strength of up to 40 percent.
@Russ S that's not from too much water, that's from adding aggregate. Concrete will fully set underwater. Also adding aggregate and preparing the job properly won't have that effect. If the aggregate has no where to move the water won't displace it. Aggregate is not concrete, water doesn't weaken concrete.
You have to be very careful not to damage the tiles with the angle grinder.
The step with the ball you can leave out. No professional does that because you go over the joints with the rubber plate and after a little drying you come back with a sponge - as shown. But you have to work diagonal over the joints NOT along the joints. This way you'll get the beautiful shape of the joints automatically.
Imagine all the professionals sit there and play with a ball while making hundreds of square metres of tile laying - five head 😂
😅
Для профессионалов эта идея наверное не подходит, но я в восторге от этой идеи! Метлах на кухне уже расшатался. Клей высох. Мастер так и сказал: Снимать и снова укладывать. А это сколько проблем! Очистка и прочее. После этого видео я сама справлюсь. Благодарю Автора этого видео!
Renovator is better for this work ..
I always use renovator
Not to mention the ball leaves a con cave grout joint which will fill up with dirt. Not sure why he didn’t try to match the grout color.
У него просто был шарик красивый, и он решил его показать всем.
У меня тоже был, нужно поискать.
@@krasnonosov51 а ты знаешь какое значение слова на грузинском твой ник ( чатланин?)что-то вроде проститут или точнее пидор. 😁. Так что подумай.чатлак звучит правильно.
У меня было два, но один сразу закотится куда-то, а второй сломался...
@@БогатыйПролетарий Вы, наверно, на него наступили. Он вполне мог продавиться внутрь подошвы... Когда обувь износится поищите его шилом в маленьких отверстиях, он обязательно выкатится, если не запропастился куда ни буль...
утром на подушке шарик нашёл....
Seems awfully risky cutting the seams like that, risking making holes in the water barrier beneath the tiles.
Extraordinaire, cette précision dans le geste et l'agilité du doigt.magnifique.
Ez egy faszsàg,aki így szeretne fugàzni ,javîtani hàt sok sikert hozzà😊😊
First mistake is White grout on a floor, i bet that new grout went dirty grey within a month, Second, although using a grinder to take the old grout out is nice and quick, you only have to just touch the tile and you are taking off the glaze / chipping the tile. Whats with the ball bearing ??? you then squeegee the floor after running the bearing over the grout line putting the grout back into the grout line, then you wet sponge it again, so what profile there was you created by using the bearing as a molding tool has well and truly gone. What a pointless waste of time. Also the grout was far to watery. Please don't use this a guide for re grouting a floor. There must be lots of videos on here that show the correct way to do the job properly. Rant over. Nice grout float though.
So what colour would u use for grout?
@@ginoginetti Grey , all day long. There are many shades of grey to choose from. Black at a push but it will stain all your grouting tools and clean up takes so much longer.
I really don't like he's way of grouting
@@ginoginetti я, например, обычно в серых тонах затирал в бытность работы плиточником.
This ball trick is really unnecessary, even without him canceling the profile afterwards. But a nice and clean technique beside that.
Good technique and quite easy for filling up the joints between the tiles after cleaning up the old joists which have become dirty and weak as well.white cement slurry is deliberately chosen to make the video clip more clear to understand the workmanship which is absolutely perfect. Cutter is used to clear the old joints of cement quickly. Slight chipping of corners is covered with cement slurry after drying and rather joints are more tough as the corners are free of glaze and have become rough.
Scheiß Fliesen. Ich hasse diese Dinger. Im Frühjahr werde ich sie aus der Küche entfernen.
This is a realistic view of what was done. Excellent comment!
@yuvrajmehta7744 Indeed poignant, well worded and relevant comment.
Some people don't realize that ceramics, cement and even gypsum plaster are but a few of materials which have been formulated and modified in numerous ways by either trial and error or by experts who understand how to use existing products,
One thing that came to mind is Expansion cement or anchoring cement.
One of the best pieces of evidence that there is a lot of very bad advice on youtube.
У человека слишком много свободного времени, что бы заниматься этой мазнёй.
Time you do the whole floor I'll be finished at home having my dinner.
Can't believe just watched it.
😭😭
😂
Ce monsieur il a du temps pour cela c tres long mon Frere comment tu trouve ton dos le soir
1m2 per day... that's a legit tradey
Id like to think this “section at a time” is just for demonstration purposes only not so much a technique. What’s the proper way of going by this in your opinion?
@@juanc.9735 Just every standard grouting technique recommended by the manufacturers. They are usually written somewhere on a flyer bundled to the grout.
The same goes for everything on a construction site. Idk, mixing concrete, routing the cables, HVAC installations. This may differ in some states - so you should be aware of it when buying some fancy shit on the Internet. Most European appliances would be useless in the USA, so all the tips for EU installations.
great, cost and frustration saving video. I had never heard of or seen the repair tube. Thanks.
Grout is not to be mixed at that consistency. It will likely crack or have pin holes. Also i don’t believe it would bond nearly as good as traditional method of pressing grout into the joints and wiping with a rung out sponge. But looks like a great way to shallow the grout joints tho 😂
Not to mention time consumption.. I bout fell asleep watching the video😂😂
Agreed. There is no guarantee that the grout actually ran deep into the gaps. Personally, I push grout in deep as I go, scooping off access, and working in, continuously.
If I need to repair grout that cracked/broke, assuming I don't want to pull up the tile, I'll use TEC AccuColor sanded siliconized acrylic latex caulk. Presumably it has flex as well as adhesion so it won't crack again.
30 лет класть плитку и не набраться опыта.. вы это имели ввиду?
30 лет почти в пустую...
Да врёт он, блядь буду. Тут и дураку понятно для чего он папиздел название ролика, чтобы срубить побольше просмотров 😏
Aaaaaaaa....!!!!!!
Perfectooo... !!!
Gracias !!!
Estaré aplicando esto MAESTRO!!!
Tengo guardadas bolillas de acero, justo!
I am a Jack of all trades and master of only a couple, but I must say this video was excellent. When you plan out a video of instruction this well, no words are needed. Well done sir!
Perché nn fa vedere la stuccatura da vicino?? Così si noteranno le scheggiature delle piastrelle dovute al flex col disco diamantato. Esisto soluzioni meno invasive.
😊😊
This is junk there is way too much water in the grout therefore there is no strength in the grout. DONT DO THIS
I agree starting off in the concrete trade this looked way to watery, cement should not flow so easily.@@vanrepchinsky313
Bizarrely Satisfying & Great Vid!
Шов пропилен глубоко, а новый цемент пролит лишь по поверхности, а не на всю глубину, что приведёт к провалам после эксплуатации. Шарик сформировал паз, а затем полутёрком его снова испохабили. В общем, халтура, а не работа.
Он сделал уплотнение шва. Так что все по уму
@@G.A.V.136 Это с ваших позиций. А по мне ХАЛТУРА, а не уплотнение.
@@G.A.V.136 чистить швы болгаркой большого ( ума) человек
@@G.A.V.136 Он просто запилил видос, ради просмотров.
Где, и в какой инструкции, по применению затирки, вы увидели чтобы её заливали как воду?
Had to grind out a bad grout job due to caracks and discoloration. The customer had applied some kind of sealant that created a top layer like rock. Did the kitchen, foyer, hallway and bathroom, truly a nightmare job. In the end the customer was thrilled, no ball bearings were used.
В следующем видео ждём засекреченную технологию великих рукож.. пов вселенной, как можно сделать 5ти минутную работу за 24 часа! 🤔 Действительно - уникальные технологии))
тем не менее это видео 2 ляма)
Can u tell us what the proper way to doing this is. Or what NOT to do. Anything aside from just criticism please.
@@diy1Сейчас уже 10лямов, а лайков всего 35тыс! Делаем выводы!!!
Nice skill with that trowel, looks great. Is that sanded grout?
No dummy, it was white cement. And why white cement and not grout?????
Didn't that wheel say "wet cutting only"? Can we assume that was nonsanded grout? Doesn't mixing grout that thin compromise its strength and durability?
Yes, that was my understanding, the grout is there as a bonding and sealing of the joints.
As an experiment - - I would like to see a "plan view" showing two tiles and the now-supposed protection
Chtěl bych vidět jak by neporušil Tuo rozbuškou hrany té dlažby,cha,cha
That wasn’t even grout he was using it was white cement.
It wasnt grout, it was white cement.
High speed grinder on grout line with one hand, if that grinder gets away its gonna hurt. Maybe use a slower tool. Also what's the point of the metal ball?
Have to wait another 30 years for that. 😀
Gostei muito da sua explicação, sou mulher, mas as vezes faço alguma coisa de pedreiro, aprendi o básico pq meu pai era esse profissional.
Também pq posso fazer, não precisar pagar ou ficar esperando alguém fazer. Também fazer trabalhos artesanais como vasos de cimento, fontes, aquário etc.
Obrigada por passar sua sabedoria
👍👏
انت متزوجه
If u were a child of the 80s now that's what u call marble madness 😮great 👍 work.
Tem usar a inteligência para facilitar a mão de obra mesmo, parabéns pela idéia. 👍🏼 Deus abençoe
Just now learning about this. I learned this in the 1970s using a circular saw.
Don't want to be negative, but I spent most of my working life in the flooring business and all of my crews used the grinder/vacuum combo, and the ball bearing thing was cute but the same concept as the gadgets they sell for smoothing out caulk. I'm not sure what you thought was the new technique? Regardless, well made video and it may help out some diyer or homeowner, assuming they are experienced with using a grinder freestyle like that. You can make a mess of the tile if not. But again nicely done.
My thoughts too. ;)
If one is not careful that diamond disc will chip the enamel on the tile
"assuming they are experienced with using a grinder freestyle like that."
Yeah, I was looking at that and I was thinking that I would be making a mess of the tiles. The only way I would bother with this is if I were trying to remove the tiles and keep them for myself.
It's a lot of work man I just found epoxy and re- colored my groutand spend 10 years and last and it looks beautiful and it doesn't stain because it truly truly seals
Very good Thanks ❤❤
Жду ролик с названием "Путаны держат это в секрете! Удивило даже 60 летнюю Снежанну" 🖒😁 в остальном спасибо - дельные вещи показываешь
Занимаюсь укладкой плитки,почти те же 30 лет,ролик прокоментирую так:когда собаке делать нехрен,она яйца лижет.
@@serggorovets9019 Коту.
@@Agent_Smith777 Но не отгрызает.
@@Agent_Smith777 Собака коту?
@@ИАП738 Всякое бывает. 🤣
Бомба!!! Очень круто!!! Спасибо!!!
Risky using a cutting or grinding wheel, the slightest touch on the edge of the tiles could chip the tile edges and whilst pouring the grout in might look good initially I would expect the excess water to cause cracking and shrinkage as well as weak/soft grouting, finally I don't get the point of the bearing if you're going to run over it again after whilst still wet.
Try using the rounded end of a broom stick handle. It works just as well and you can do it standing up.
- что делаешь?
- шары катаю)
I grout my tiles with thinset. Then I seal it. It has been over 10 years and still hold strong. No worries and no regrouting.n
Para 4 baldosas puede ser, pero si es una superficie mas grande lo dudo y ademas del riesgo que hay si se desvía la amoladora dañando la pieza
That's a very good trick to apply tile grout!!! It really works!!! 👍
it may work, but grout is not intended to be that runny.
Was not grout.
When i do our tiles ...it's a problem with the spacers...that are all still in ..would it be best to try and scrape them out
Caramba! cada dia eu aprendo alguma coisa diferente. Essa do aspirador de pó, a colocação do rejunte, o uso da esfera para dar acabamento. Genial viu! Precisava gravar isso pra não esquecer. Obrigado amigo!
Pra mim é simples, mas pra quem ñ é da área se impressiona
😂😂
Pega aí uma residência de +ou- uns 50m² pra substituir o rejunte, use a esmerilhadeira com uma só mão, aspirador na outra e, claro "confortavelmente" de joelhos! 😂
@@dicasdeconstrucaoereformas3170Faço com um cavaco de chinelo velho, rápido e perfeito! Kkkkk
Sugiro que desaprenda tudo o que viu nesse video, exceto o uso do aspirador para limpeza (mas SEM a serra de diamante).
Wow that takes a steady hand!
Right after the grout is se and dry between the tiles, why aren't the tiles and grout both sealed against discoloration using some kind of polyurethane like we do for wooden floors? I don't wanna spend significant time cleaning when not necessary. I'd rather leave the grout a dark color and make future stains a part of them permanently (as not to draw attention to them.)
Woah. So they now make these grout strips and one can just place those instead of grout. It definitely stays secure for many years but in the case it needs to be switched it’s a strip that you can pull out!
I don't get why you have to furrow the grout anyway. That just gives a place for the dirt and grime to go and build up. Why not have the grout level with the top of the tile. So much easier to keep clean. Someone please explain the need to furrow the grout.
I am a builder and I can say there is absolutely no reason to do so, in fact it creates a void for water to sit in only to slowly disperse to the substrate in wet areas, it’s also a great to create lipping if the tiles are slightly out of level as laid.
you must be a builder from spain ,thailand, or usa, who dont know, that the furrow have to be in level with the tile edge, and the tile edge are bent, slightly down.
THIS is the right way to do it. if you lay the furrow over the edge, which is glazed, it will loosen over time.
It seems to people don't like the videos because he takes extra steps. That may not be necessary for others, but the one thing that I do see Benefit In ,is the organization and clean up You may or may not have to do if you follow his steps
You are chipping the glazing and the tiles will turn black from dirt.
how do you get the grout out then?
@@rickdeckard1075 a degrouter
@@RagdyAndy and that doesnt chip the tile?
@@rickdeckard1075 never happened to me so far :) A lot less chance of it happening too than using a grinding wheel lol
@@RagdyAndy oh ok, thanks andy
This is not the way to fix dirty grout. FYI. You can mix even amounts of swimming pool acid and water. Soak the floor so the tile and grout are both covered in the acid water solution. Let it sit for 20 to 30 minutes and shop vac the floors. Don't scrub. Just vac. The acid will release all impurities/ dirt from the grout. I worked for a very Greek tile layer when I was young. He offered the cleaning service to people he knew couldn't afford to retile their floors. Great guy. This method works 100 percent of the time to clean grout. After you have cleaned it , take Murphys oil soap and seal your grout lines.
The grout mix is too loose .It needs to be tighter because just like concrete mix ,when the mix is too loose ,,then the finished grout will be weak.That means it will more than likely crack and then pop out of the joints especially if there is any deflection in your floor. You have to stiffen the floor with 3/4 plywood sub floor and stiffen grout mixture by not adding too much water. You should never be able to "pour" your grout. Much too loose.
Epoxy grout is recommended for stain resistant strong grout
I'm not a professional, but I've done several tile installs for myself. The grout is unusually liquid in this video (lots of water) and since, I as believe tile grouts (at least, sanded grouts) are basically a Portland cement base mixture, how is the hardness and durability after hardening and drying? I wonder about its durability.
you must have a steady hand or chips the tile
Do you know that God has created a way for you to receive mercy and experience freedom in Jesus? And its love for you - so that you have eternal life and forgiveness in Jesus! God, to fellowship with you, gave His Son as an atoning sacrifice. Jesus has paid for you to save you from eternal condemnation because of sin. But this only applies for those who are willing to repent and accept the Lord Jesus in their lives! Repent I beg you, and desire Christ above all else! Love him and follow him to the end, not you you will regret it Would you totally give your life to Jesus Christ and accept him as your personal Lord and Savior?
Çok güzel olmuş ellerine emeklerine sağlık 🍀 🇹🇷
Not gonna lie, that's too much work for me lol. I'd just paint the cracks black or brown.
😃👋👋👋СУПЕР !!! Браво МАСТЕРУ !!!
Для расшивки швов ушм лучше использовать отрезной круг по металу.Так безопаснее для плитки.
УКАЗЫВАЙТЕ пожалуйста какие материалы были истользованы! Спасибо.
А что не видно?
@@Pravdin-Eduard Вижу сметану! 😁
@@ИАП738 смент три кулька написано было)))
Nice one I've try it many times especially when you are inside of a house that is finished , the diamond disc you should put in other way ...
Es evidente que tiene un muy buen pulso. No creo que astille baldosas ¿Ven como se hunde el disco de corte? Creo que ocurre porque el suelo de apoyo de la baldosa es demasiado débil en algunas partes. El disco se hunde sin que se ejerza una gran presión. Idea: un accesorio unido a al cuerpo de la herramienta y que reemplace a la mano que sostiene la manguera permitiría agarrar la cortadora con ambas manos. Ganaría mayor seguridad para evitar accidentes y mayor firmeza para cortar y evitar posibles rayones en las baldosas.
the ball bearing technique is new to me but brilliant...will add that to my grouting process.
wouldn't a spoon do the same thing as a ball bearing ?
@@smerchly spoon, broom handle, bic pen cap...
@@grumpyolddude439 The bricks behind my fireplace was done by my fingers , no tools required . That was 35 years ago and still looking great .
Use a parte sem ponta de um lápis cilíndrico grosso que fica ótimo.
احسن به این فوت وفن و رایت کاری موفق باشید ممنون از راهکارهای مناسب ❤❤❤
Bonjour, très bonne technique.
Une autre technique que j'utilise pour tout les joints silicone ou autre c'est d'utiliser l'arrière de la cartouche de silicone pour retirer le surplus.
Ça fait un joint parfait.
You are genius. I hope my house will not be refurblished by you!
Muy bien felicitaciones por su excelente trabajo.
Genera ideas. Gracias por su vídeo. Es didáctico y motivador. Le envío cordiales saludos desde México.
I just hope you don’t have a heating floor 😮
If he did it wouldn't be directly under the tiles and he would know 😂
Фуфло
A buddy of mine use to let the grout set up for a little bit so it was just a little moist, not wet, then take the end of a broom handle or any wooden handle and run it down the grout line the same as this.
I always used the side of a penny. Works great.
Ficou bonito o acabamento. Vou testar em casa. Obrigado.
А при резке болгаркой ,разве края плиток не образуют сколы...и тогда не будет красиво...
Por isso ele virou o disco, assim o atrito no esmalte fica ao contrário,não afetando a peça.
Я делаю наоборот : болгарской полирую, если же нужны сколы, то проще их делать зубилом.
У него швы довольно широкие 3-4 мм, сколы могут появится только если болгарку уведёт в сторону. Но у него остаётся старая затирка по краю плитки, которая портит весь внешний вид шва.
@@gosh702iv5, так ведите болгарку ровно, в чём проблема? Может болгарка бракованная? В космос летаем, а тут ерунда какая-то...
@@krasnonosov51 сложно вести ровно рез болгаркой, при этом держа другой рукой пылесос.
Think out of the box, smart man
Още един откривател на топлата вода ! Искам да го видя на 150 /200м2 с тая сачма ...
Jak się chłopu nudzi i ma sracz na 6 m2, to ma czas na takie zabawy. Inna sprawa, że to jest robota zrobiona po chuju, bo między płytkami będzie się brud gromadzić.
Bravo impeccable !!
ДА ОН СМЕЁТСЯ НАД НАМИ! Быстрое движении камеры (и предметов) создаёт настроение непринуждённости. Медленное - наоборот напрягает, кажется, что сейчас что-то вот-вот может произойти. Но ничего не происходит...
Estupendo!!👍🏼
белая затирка на полу, нет слов...
Your smart guys thanks for showing
This would be harder to do with the new tile ready pans and kerdi foam pans. You would have cut the water proofing barrier and the pan would then leak.
This repair was not a shower floor, but watered down cementious grout will not cure properly.
Works great on walls!
Что вы там курите парни? На плитке хорошего качества и если клал спец - зафугуется ровно без этого идиотизма, а если плитка некондиция какие нах шарики?
Ok, for who say this takes forever, yes, but I’ve got a tool that can use on regular grout (mixed to consistency that us tilers like and use, imo that is) and then just dip correct size “ball end” in water for some gliding agent to tool grout joints. Ya do this after 1st wash and before final buffing stage. Does add an extra step; so does add time, and imo, if can do great job with joints and being consistent w/ everything…..really don’t need to use, even if doing a regrout.
Is cool to watch though, and see. Maybe for a patch repair or something, but not gonna do for a 10k floor laying down using tile, as yeah, money ppl aren’t gonna like those extra hrs 😂
Já faço essa mesma técnica com cabo de vassoura, e fica top.
ELE E BULITAÇO VC E CABAÇO.KKKKKKKKKK
good job sir👍
there is coloring for the grout. No need to redo the grout
Excellent you are the pro. Great video. You make me speechless 😶
Kiedyś w 80-tych latach do fugowania używało się tylko białego cementu i ta metoda była powszechna. Różnica polegała na tym ,że do nakładania używało się packi z styropianu a przeżynało fugi odpowiednio zaostrzonym patyczkiem. Nihil novi...
👌🇵🇱👍Pozdrawiam
przecież zamiast kulki stosuje się profilowaną szpatułkę ! co to Q za nowość ???
😂magia normalnie
A ta kulka to po co? Sprawdziło by się to tylko na idealnie równych szczelinach i idealnie położonych płytkach
@@damiandamian7384 amatorszczyzna...
Sáng tạo quá bạn ơi
Заменить затирку герметиком на масле или белым силиконом) будет стоть долго и не пачкаться)
Не укладываю плитку 30 лет, но слышал ещё лет 20 назад, что так же плиточники проходили закруглённым торцом зажигалки по швам. Смысл тот же, выходит так же.
No, no NO! INSTEAD, USE A STEAM CLEANER MACHINE. Fast, EZ, and much better 1st choice.
A steam cleaner cant clean everything. If the customer have wishes you do it.
@@Holzwuermli Just do it. Go buy a steam buggy, then use it. You'll never want to be without one ever again.
@@byenzer5101 nein man. Wenn der Kunde einen Wunsch hat, dann wird erfüllt, egal ob man das sauber bekommt oder nicht. Es gibt Menschen die wollen es nicht gereinigt haben sondern neu! Schonmal daran gedacht?