That's my mower! Every couple of years I've had to spend about $100 on parts to fix one thing or another - and parts are readily available. Just fixed the steering link and put new blades on for about $50 total - it works like brand new. And the nearest equivalent of a new one is over $2,200 so I feel like I just saved two grand.
I can see the appeal for this mower. There are many cosmetic differences, with relation to the dash & some controls differ, slightly. I have a McCulloch M14538 (14 HP Intek, 38" cut), Peerless 6 speed, made by Husqvarna in their Orangeburg, South Carolina factory in 2011. It's been in Australia ever since. I'm the second owner, since the end of 2015. The original owner had it for (less than) it's first 4 years. It's still running as good as it was when it was built, as it should, when well maintained. That mower would be one of the last made under the (then) Electrolux owned Husqvarna. Husqvarna became independent again in 2006. They make Poulan, Jonesred, Klippo (now called Husqvarna Klippo), which is why so many parts are interchangeable.
I like my Poulan Pro. I had a Dynamark that I bought used about 25 years and the engine finally got weak so I retired it and got a Poulan, which looked to be constructed about the same as the Dynamark I had. I figured if the Dynamark lasted as long as it did, the poulan should last until I'm in my grave. It seems to be well built and does a great job.
very good video. and good knowledge, so the heavy duty deck part is different to my prouland tractor, mine is original but your sounds better, how I can get one , where you got it ? and how is the procedure to replace original with a heavy duty deck...sounds as hard task
Greetings, I have a 2002 model and am trying to replace the stationary clutch idler pulley. It loos like the bolt goes through the frame and has a nut on top. I think it is covered by the steering gear drive assembly. Do I have to take all that out just to replace this pulley?! (I'll also try your email.)
I have a popular for it for free from my neighbor but she won’t turn over at all no power nothin changed some things and still nothing what else could it possibly be any suggestions ?
Hi, I need help , I’m trying to replace my trans drive belt on my 54” deck 2006 Poulan Pro and I can’t get the tension pulley to budge in order to get the belt on …..
I got one like this for free. I was able to adjust the valves and bypass the safety switches so the motor runs great. But it seems to be stuck in gear. Will stop if I let go of the break, and won’t move forward nor revers. Please help me.
That's my mower! Every couple of years I've had to spend about $100 on parts to fix one thing or another - and parts are readily available. Just fixed the steering link and put new blades on for about $50 total - it works like brand new. And the nearest equivalent of a new one is over $2,200 so I feel like I just saved two grand.
I can see the appeal for this mower. There are many cosmetic differences, with relation to the dash & some controls differ, slightly.
I have a McCulloch M14538 (14 HP Intek, 38" cut), Peerless 6 speed, made by Husqvarna in their Orangeburg, South Carolina factory in 2011. It's been in Australia ever since.
I'm the second owner, since the end of 2015. The original owner had it for (less than) it's first 4 years. It's still running as good as it was when it was built, as it should, when well maintained.
That mower would be one of the last made under the (then) Electrolux owned Husqvarna. Husqvarna became independent again in 2006.
They make Poulan, Jonesred, Klippo (now called Husqvarna Klippo), which is why so many parts are interchangeable.
I like my Poulan Pro. I had a Dynamark that I bought used about 25 years and the engine finally got weak so I retired it and got a Poulan, which looked to be constructed about the same as the Dynamark I had. I figured if the Dynamark lasted as long as it did, the poulan should last until I'm in my grave. It seems to be well built and does a great job.
Boy you really know the Poulan tractors! thanks
You made a very helpful video
I have the same year mower made by husqvarna. The pin in the deck level arm is bent and I don’t know what to fix. Thanks for the video
it's located right under seat under battery
very good video. and good knowledge, so the heavy duty deck part is different to my prouland tractor, mine is original but your sounds better, how I can get one , where you got it ? and how is the procedure to replace original with a heavy duty deck...sounds as hard task
i have a pp24va54 poulan pro mower. can you tell me what oil filter to buy?? I can't seem to find that information on line.
How do I switch out the deck height arm? Have you ever done that?
Mine has been good up until this weekend... can't get it to start...
I have a 2007 Craftsman lt 2000 is it the same as a Poulan Pro
My popular (hydro) hangs up in forward and reverse. I have to keep pumping the pedal to get it to change direction. Any advice?
Wow that’s exactly like my LT 1000!
Greetings,
I have a 2002 model and am trying to replace the stationary clutch idler pulley. It loos like the bolt goes through the frame and has a nut on top. I think it is covered by the steering gear drive assembly. Do I have to take all that out just to replace this pulley?!
(I'll also try your email.)
What makes it stop going in reverse..2012
Thanks for this video!
How do I disconnect the auto-stop when getting off the seat?
My cable seems loose lawnmower won’t engage
have a poulan 38 inch, will a 42 inch swap right on? grandfather has an lt1000 42 inch and by memory everything is the same the way it removes.
Issue with front tire. Put new tire on old rim and I ca not get it secure. Why?
I have a popular for it for free from my neighbor but she won’t turn over at all no power nothin changed some things and still nothing what else could it possibly be any suggestions ?
What is the battery cca? i need one for one that my husband's work has but no battery trying to find what cca it takes.
Hi, I need help , I’m trying to replace my trans drive belt on my 54” deck 2006 Poulan Pro and I can’t get the tension pulley to budge in order to get the belt on …..
trying to locate the gear spring on the poulon pro
My popular pro will click but won’t start I’m trying to fix it what do you recommend
I have a Polan push mower instead of a riding mower
I am looking to buy Poulan Pro used riding mower with Vitek 19.5 engine
Is it a good choice any feedback appreciate it thank you
Any idea what to check on these when the tractor dies when engaging the blades? The blades are not jammed.
Did you ever find out
I have one!
I need help with my mower it crank but won't start
Mine broke the blade engagement cable from the lever !!!!!!
I got one like this for free. I was able to adjust the valves and bypass the safety switches so the motor runs great. But it seems to be stuck in gear. Will stop if I let go of the break, and won’t move forward nor revers. Please help me.
I have the same issue. Starts but stalls when put in forward or reverse ... And it stalls in neutral if I let off break too.
John Deere all the way
Craftsman or Poulan are weak. Can't hold a candle to a Hustler.