Timney Glock Trigger install on Zev OZ9
HTML-код
- Опубликовано: 8 сен 2024
- Installing the Timney Glock Alpha Competition trigger in the Zev OZ9. The OZ9 has an integrated locking block so the Timney directions will not work. I use this method on standard Glocks as well since I find it easier not having to try to keep the spring down when inserting the locking block.
no bs intro. got to the point very nice
Perfect video. Thank you sir!
I copied this exact setup but the trigger fails to break. It’s not a connector bend issue; the trigger bar physically cannot travel far enough to sufficiently depress the sear. The right angle section of the trigger bar bottoms out and hits the frame early, before the cruciform can even contact the sear. The radiused end of the trigger bar towards the rear of the gun doesn’t even touch the connector. What gives?
I tried the Zev connector and 3 different lone wolf connectors. My particular model is the compact
I'm about to do the same thing. I've got a Timney Alpha for the Glock 3-4. I've also got a Johnny Glock Trigger shoe and connector. We'll see what happens.
Which one is better?
I have the same set up. Been disappointed with it so far. Trigger safety shoe is catching the frame on reset and been a pita to dial in. Seriously considering trashing it & putting in a Zev or Overwatch kit.
Just wondering if you have the original zev trigger stuck on the frame issue before?
By chance do you have any experience installing tactical pontoon into zevs? Curious if the process looks similar
I have a zev as well. Was the trigger you bought the 3-4 gen or 5th gen? Not sure what fits the zev, i don’t own a glock for comparison.
Gen 3/4
I’m having a problem when installing this trigger. I got the right version (3/4) and completely followed the guide to install it. But the trigger doesn’t work as it should to release the striker. I tried everything I can but still can’t solve it. Do you have any ideas about it?
Do you have another connector you can try? Some connectors break later than other, so your’s might be breaking to late. Or you can try bending the piece of the trigger bar that rides on the sear down a little bit so it engages the sear sooner.
Do you have a Gn5 trigger installed?
I’m curious if you had any issues seating the timney sear housing into the Zev ejector housing? I tried installing it in my OZ9 Hypercomp but it doesn’t fit all the way in.
Nope. I have no issues. Is that tony screw removed or very loose when you try to install it?
@@ZEE0H6 no I tightened the hell out of it to try and get it to seat down in there better but no luck
What gen trigger drops into the oz9?
Gen 3/4
Did you use the Zev connector or did you swap the connector?
I’m using the Zev connector. Feels the best out of the connectors i have, LWD, Glock - and dot.
Struggling getting my trigger to travel far enough to the rear. Thoughts?
Sorry for the late reply. Do you have another connector you can try? Some connectors break later than other, so your’s might be breaking to late. Or you can try bending the piece of the trigger bar that rides on the sear down a little bit so it engages the sear sooner.
Any idea if this will work for the OZ9c as well?
Yep. They use the same trigger.
double feed how do you solve the problem i am facing in my oz9 new
Double feed is most likely caused by magazine problem. Feed lips spread to far out to to much.
@@ZEE0H6 Ejector
Extractor
PLUNGER SPRING
DEPRESSOR
What do you use? I have extrac problem.
@@user-uk5wu9mm6f
30724 ejector
Zaffiri Precision billet extractor, 2 years now with no problems. I had extraction problems with the Zev extractor. I tried Apex 102-104 extractor and this didn’t work either.
Zev extractor spring and plunger
@@ZEE0H6
Oh my friend, this information is very helpful to me.
.
Before I used a Mag glock 17 gen 5.
.
Bullet master FMJ 124gr 150 round no problem
Bullet master LRN 130gr
150 round no problem
(onlythailandbullet)
.
When I come back to use pmag magpul it doblefeed to many
A lot of problems with 115gr ammunition.
Winchester 115gr / Thaiarm 115gr / sig365 115gr
Plunger, plunger spring. Just went thru this exact issue. Or worn extractor
What generation glock Timney trigger?
Gen 3/4 Timney
So how did it run and how man rounds
Runs great. Bout 100 live rounds or so. A bunch more dry firing.
Gen 5?
It’s an OZ9 so gen 3/4 cofiguration
All Zev trigger internals ?
Overwatch billet striker
Zaffiri Precision billet extractor
Timney trigger
LWD adjust overstop trigger housing
Jager tungsten guiderod
@@ZEE0H6 by “billet striker” do you mean the NP3'ed Gen1-4 9mm Striker? I can’t find billet anywhere
@@EzraLopezUSPSA hey sorry, that’s the striker I used