Broken shark ion robot vacuum can we fix it? Very interesting find
HTML-код
- Опубликовано: 3 мар 2020
- So today I got some more robots in and this one really interested me. So in this video I decided to record me taking it apart and fixing the issue which was simple but a first for me just shows you never know what can be wrong with these things . Also make sure to pick up trash that can cause issues before vacuuming.
Here is a list of the tools I use to work on these robots
Torx Bit Kit
amzn.to/3NugrU4
Rubber Mat
amzn.to/3PbrmU5
Grease for electronics
amzn.to/3N9e6gh
Cleaning Supplies
amzn.to/46630RB
New battery
shark iq
amzn.to/43nim2A
shark ion
amzn.to/43nim2A
Shark RV1001ae Spinner Brushes
amzn.to/2MsFZnP
Shark RV1001ae Brush Roller
amzn.to/3chvBKi Наука
How do I get my shark sweep/mop brush to spin. It comes up with error 2. One brush does not spin & keeps telling me to check under it.
Thank you. Just seeing your troubleshooting process is helping me build the will to try to fix my loud bot instead of trashing it. Would you mind adding the link for tools? Fingers crossed that I’ll be able to figure it out. Congratulations on the new baby. I hope you’re able to catch up on rest soon.
Shannon Allsworth thank you hope it helps you
This was somewhat helpful, but my rv750 wheel assembly is covered by the bottom. I removed the battery and all of the screws, however, I will need to separate the bottom from the top. Do you have a youtube showing how to separate the bottom from the top so that I can access the wheel assembly?
I have a Shark IQ and it got a little wet today, and no longer recognizes it's base charger. Any ideas?
If I have a Shark AI with xl base that thinks it's too close to a ledge to operate, can I buy a IQ and it charge & use the self empty base I already have?
My shark VacMop Pro won’t turn on do you have any suggestions?
In true "deh" mode I tried to get my shark to ,"go" but nothing. I checked voltages of charger and battery, both good. Contemplated taking apart and decided to watch your video. Shock me with an on/off switch that I had not seen!!! Shark runs while I sit red-faced. Thanks
What is acceptable voltage for a battery? I have a 14.8V and it is reading as 11Vm, not sure if that is enough or time to replace.
Hey, where can I find someone in my city (Miami) that does this type of repairs. I got mine for Christmas...got wet and stopped working. It charges but the buttons don’t work and when I try to start it from the app the clean and dock start blinking. It says to clean the cliff sensors, I did but that doesn’t fix the problem. I’m about to throw it away and have only had it for 2 months. Any suggestions?
I have an IQ robot with a broken cliff sensor. Is this something you can fix?
Hello friend, how are you? I like your work. Have you been able to repair the ones that don't want to return to base? thank you
Can you find parts for repair for shark robots ? Could'nt find any on the web.
I was literally just shuttering at you dropping your screw in a pile of other screws and your spit bottle and then at that very moment you acknowledge it 😂 looking for a video to help with a grumbling sound. I found this, which doesn’t help, but I did learn I need to change my filter!!
I have a newer Shark AI. When on the charger the battery light flashed red. How come ?
What does it mean when the max is lit up red and the vac won’t move?
Mine keeps going around and around and stops ! Anything u know will help?! Plz
Smitty - Do you have a Vacuum for a Shark Model 725 I can buy?
I cleaned my shark vacuum all sensors and everything is good. It still says to clean it but it’s clean . Can you please help me.
Mine say obstruction #2 please check under Robot. I took everything apart and cleaned really well. Seem like the right wheel tries to move but the left side locks up. Do I need a new wheel or just a sensor
Carol Gregory bad wheel take apart clean out see if the gears have hair inside them.
Io have the shark UR1105ARUS
It ran over dog poop I clean with a wet sponge and soap when it turns on it only flashes a red battery. On the charger same thing I have 4 volt on the robot and 19.8 on the charging base and I replaced the battery still nothing and is this worth fixing and do you sell refurbished robot
Hey Smitty, I have a Shark Robotic vacuum RV70. How do I disassemble it to inspect inside and wheels?
Buster Barnes remove the screws separate the body then remove each wheel and then take them part.
I’m looking a wheel motor wiring harness for a shark r75
How do i take off the wheel of something is stuck on it my issue is the same but your issue stopped u before i can learn to take off the wheel please and thank you
How do I fix the shark when it says to close to a cliff
Hey man, I started having an awful sound with my ion, and realized the main brush wasn’t spinning. Replaced the motor and still having issues. Any idea what else it could be?
Did you check to make sure the case itself that the motor goes and wasn’t melted and that the belt had good tension
Video gives me hope. Our shark fell into the shower without out us knowing. I accidentally turned the shower on it while it was upside down. At that point only one wheel was turning.
Is this a fixable problem and are there parts out there ?
Hi! I have a Shark QR1WOOSRUS that goes on erro 14, but I don´t have a BotBoundary strip.
This did the trick for me! Thing has sat in my office broke for 2-3years. Glad I didn’t throw it away!
My shark ion is 14 months old. I keep getting error 6 to make sure the bumper is moving freely. It is moving fine and I have cleaned the sensors. Customer service simply offered a discount on a new one. Is it worth trying to take the bumper off to see if there is something under it, like dog hair, causing an issue?
I have the same issue with mine. I took the bumper off and cleaned it, but I still get the same error. I just called customer service and they said it's unfixable. That seems odd to me.
I would like to buy a shark robot vac?
Hi I have a RV700_N and the MAX light just flashes and it doesn’t start up. I took off both wheels and there nothing in there. What else could it be?
Rocio Ramos that probably is the front bumper being stuck. Remove it and see if the metal pieces are bend
My 1001 model had a head on collision with my dogs poop and after cleaning it up, it gives me error 14 that is it is stuck on the magnetic boundary strip so I took the bumper off and clean those sensors off also, even thou I didn't see anything that cleaning could have helps and after re-assembling it, it's still error 14 and it's now saying it is stuck on the magnetic strip or also that the bumper is stuck. If there is a sensor gone bad, how can you determine which one to replace? Thanks
Hmm thats interesting do you have a strong magnet or speaker laying around? Might be stuck and be able to run the magnet around the on the top and bottom to loosen it up. Might also want to take the whole robot part and make sure nothing inside of it a lot of times the issue isn't the poop its the fluid and pee around the poop that makes the motherboards and sensors go bad.
My robot won’t go, beeps clean then max? What can I do
I am having a problem with my bumper. One side is getting stuck and the robot won’t run. Is it easy to take off the bumper to fix it?
Alexandra Ryan yes five torx bit screw and pops apart then you will need to rebrand the metal tabs on that side
How do I fix the red clean and ! On my shark ion rv750 ?
Mine has the same problem. Push CLEAN, it goes about 3 feet the the red clean and ! come on. I need help also.
Do you have the wheel and motor assembly for an RV750 Right?
Yes I do now
My shark stops right when it leaves the docking station....says check for obstruction...I've taken everything apart cleaned ...still only rolls a few inches and won't go further
How do fix the clean+dock flashing code Rv700
Thanks, I checked the battery, and it was charged. But you showing me there was an on-off switch did the trick (DUH!). It's now clearing the floor.
My shark is 9 months old. It ran through pet poop. I took it apart cleaned and let it dry. Never has worked again. Has cliff sensor errors. Anyone buy them for spare parts ?
I have a shark robot that is 2 years old and just started spinning in a circle. Will not do anything other than spin to the right in a circle. I have cleaned everything. Replaced the front wheel. Hasn’t helped. Advice?
Have you taken the right and left wheels apart and cleaned? Could be sensor issue, motor issue , gears going bad in one side, or motherboard not sending correct voltage .
Great help hope you’re new babies getting really big by now. Tks for the demonstration but do you have a link to the T10 Torx bit set you prefer please? - novice alert 🚨
Thank you they are getting big. Here is the set I’m using now
www.amazon.com/dp/B09GPXBYC1/ref=cm_sw_r_as_gl_api_gl_i_Q6XMJ4YXYXHVQ1T8749X?_encoding=UTF8&psc=1&linkCode=ml2&tag=smittysworld-20
Hey man. Mine won’t work. I did everything cleaned it all out and checked everything. When I put it on the dock and press clean it lights up blue and the battery flashed 1 red bar and then to 3 red bars and then nothing happens. Help!
This is exactly what mine is doing. Ordered a new battery. It comes today. I guess we'll see if that fixes it.
The one wheel on mine just spins freely. I can’t find anyone to repair it. Do you have any suggestions?
Watch my videos find the part on ebay and order the tools you need on amazon. Saves you a ton of time and money or just order a new one and sell the old one for parts.
What is the name/type of your long-reach screwdriver/screw set? I have a very old set of tool heads that won't reach as they are all short. Thanks in advance for any help.
amzn.to/3EmtqlF
Thank you so much.
😀
Hi, I have a Shark ion 1001ae. I love it. Anyway it's giving an error message that won't go away. Error #10 put me on a flat surface. It's on the flat surface and won't start. Please help if you have any tips or lead. I've cleaned all the sensors.
Johnny Marshall sounds like a wheel could be stuck off the ground a little bit. try pushing wheels in and see if they are moving up and downz
@@SmittysWorld thanks. So they go in and out freely. What I notice is that one side clicks when it's pressed past a certain point and the other does not. Are both sides supposed to click?
Johnny Marshall they shouldn’t click could be a broken piece in the wheel making it say it’s not on the ground I’d remove the wheel that’s clicking and examine and compare to the other wheel.
Sounds good. I'll try that. Thank you so much!
Just wanted to tell you that you helped me fix it. Thanks alot. I'll keep an eye out for your helpful vids in the future.
What screw driver is that. Mi e has weird screws
Torx bit
My shark robot ran through some dog poop. Cleaned it. Will charge leaves the dock. Then stops. What can I do?
Honestly either take it part and clean everything with 91 percent alcohol let dry and try or throw it away
I have an RV851WV that I can't seem to figure out. It acts completely dead. Tested battery voltage, 13.8 V, charger shows 19V across the terminals, switch flips on and off, and can't seem to get it to power up, no lights or chime. Shark customer service said I needed a battery, replaced it and no change. Any recommendations on where to go for diagnosis?
Did it get wet?
@@SmittysWorld no. My wife turned off the schedule via the app before we went on vacation, came home and it was unresponsive. No one was here to possibly mess with it, and it sat on the dock the whole time.
So somehow just by taking it apart, I managed to make it work. Tore it down to the board, plugged the battery in, and it fired up. Slapped it back together and it's been working fine since. I'm guessing it's got a loose connection somewhere, but I'm keeping my fingers crossed!
@@wrifraff sorry I never responded just seen you had messaged back that’s awesome you got it working
I'm in Bartlett Illinois where could I find a place to repair my Shark the wheel
Chances of finding a place to repair it are slim to none. eBay is only place to find parts. I have stopped selling parts because of eBay fees.
My shark IQ is saying too close to a ledge error number seven is there a fix for this it is setting in the middle of the floor
You need to clean the sensors make sure all the sensors are clean now to bring on them and then you need to check your bumper make sure it’s free check your wheels and make sure that they are pushing in and out him and have a good spring tension and sitting on the floor flat and you could be any of those issues. Unfortunately the new roebucks when I have issues isn’t always so simple so you might have to contact shark and if you’re within a year of purchasing it could be under warranty
Would the battery have anything to do with the robot not sensing the charger base?
I shark robo vac started flashing clean and!. I cleaned it put back on charge ,no lights come on at all.Only week old???Can anyone help??
Jacqueline Cipolla check charged and sensors. I would warranty it or return it for another one if your having issues this soon thoS
Hi! My shark ion robot 700_N just won’t turn on, won’t even charge. Bought a new battery and still.... nothing. Charging lights do not come on when it’s on the dock and on the on position, nothing lights up. Any ideas?
Cheyanne Childers could be a few different thing. First most batteries are low or dead on arrival so could be the charger is bad, could be the charging contacts on the bottom of the robot. Could be the on off switch. Worst would be a bad motherboard. Check these things , turn on off robot see if wiggling they’ll switch or on off back and forth will cause it to do anything. Check to make sure power on the charging station is working. If you have a volt meter test the charger , the charging pads and the switch.
Smitty's World thanks for the input! I appreciate it! Will try all of that
Hi There @smitty'sworld!! I have a Shark ION model RV852WVQRG that is having issues. It's still running and moving fine but when I move the one wheel it seems like the gears are stripped. I'm going to follow one of your videos for taking the wheel apart so I can get a good look at the gears/wheels. Do you have replacements for this model? 🙏🏼 Sincerely, fellow Floridian! 😊
I can get them for you or I might have some
@@SmittysWorld sweet!! Thank you!! I will let you know.
Hello. My shark ion has been bumping into everything since the day I got it out the box. I wiped off the sensors but nothing seems to help. What else can I do? Please help!
Mikesha Huntley when you mean bumping it just going till it hits something then turns and moves to another area and bumps something ? This is normal unless you have a shark iq robot . These robots have a feature built in that slows them down before they hit something but it’s normal to hit everything .
@@SmittysWorld Yes, that is exactly what it does. This is my 2nd shark robot, the 1st one did not bump into anything so I'm not use to this. I currently have the Shark ION Robot Vacuum R75.
Mikesha Huntley some of them are better at slowing down and not hitting stuff as hard but they are random navigation bots unless you buy the 1001 which has a camera and maps out the floor plan. So it’s gonna move around once the bumper gets pushed in it will change direction.
@@SmittysWorld Got it! Thank you for the education and quick replies.
Can I ship a robot to you for repair ?
what screw driver did u use
Long shaft torx bit set. There is a few different sizes in the bot mainly t8 and t15
Is your EBAY store open? I could not find it.
Email me smittysworld2015@gmail.com
@Smitty's World, nice videos! I need a right wheel assembly for a 850, do have any around? Actually, all I needed is the large nylon gear that drives the wheels. I could not find your store or contact info to save my life.
smittysworld15 send me a message I might have the gear by itself.
www.ebay.com/str/smittysworldstore
Smitty's World do you have the computer board on model rv761_n??
How do you know if the wheel is broken
There is a lot of different ways to tell sometimes not as easy as others. Check to see if it’s free spinning or bound up.
Do you do repairs of people ship shark robots to you? No one in Greensboro will work on em!
I just took both wheels off and the little fuse like things was good and nothing around the wheels
Carol Gregory smittysworld2015 at Gmail is my email send me some picture
I'm getting error #7
Hello, I need to repair a robot that is damaged, it indicates that it is on a precipice. Thank you
Hi
Do you have a video on the WV220 hand held vac, it came with the 87 combo charging station.
Ed Stapleton I have one on changing the battery. I can make one what do you need to know about it?
@@SmittysWorld complete housing break down, any replacement parts available, etc.
@@SmittysWorld also are you planning on doing vids on the self-emptying model?
Ed Stapleton I can make a video and do have plenty for sale let me know the parts you need. I don’t have plans right now to do self emptying yet I will once I get ahold of some models that are broke to see what common issues there is.
@@SmittysWorld I'm guessing I need a motor for the hand held,i switched out batteries and nothing changed, are there other common issues with the hand held?
Hey man... I've tried everything with my Rosie. Do you do repairs?
No unfortunately I do not know what kind of issues are you having on what model do you have
How do I fix the red flashing clean and ❗️?
Tioka SCHLUTER what model do you have
Smitty's World - the 750
I have the same issue. The side brush seems a little stiff, but other than that nothing obvious. I also have an RV750
Have you had a ! (Red) + Clean + MAX flashing blue error.
William Smith what model
@@SmittysWorld RV851WV
Hi You make great repair videos.. ? I have a shark that my dog pee’ed on. I noticed smoking from where those motors are on side nothing seems to light up as far as buttons.. is it Worth fixing?
BROWERPOWER 2010 dog piss will make it not worth fixing it corrodes electrical parts really bad so it’s gonna be nasty and not cheap to fix
My shark runs for luke 10 seconds and says returning home
My robot turns on and works for like 10 seconds then it stops and a red❗️appears I checked on my manual and it says the suction motor needs something done. Ok so what happened to my robot was that my cat sprayed on it lol I know it sucks. The question is can it get fixed???
jay Verduzco suction motor might have gotten spray in it or the motherboard honestly try getting it replaced under warranty before trying to fix it .
Smitty's World that was fast thanks lol the problem is this happened a year ago or so and don’t have the paper work for it. You think is fixable ?
jay Verduzco it’s fixable for sure but could get expensive since we don’t know exactly what the true problem is. Take robot apart see if there is any spray corrosion on the motherboard then go from there to the suction motor .
Smitty's World thanks for the help😉 I will try I guess I got nothing to loose it been sitting in my closet useless lol
Took out the vacuum motor and want to know what voltage the motor is so I can test it , please ?
Depends on model 6v to 12v should move it up to 16v
@@SmittysWorld I am trying to test the motor. model 725 . Just found the sticker it is a 16.8volt motor. Do you have a replacement motor?
@@SmittysWorld Do you have a replacement vacuum I could buy?
Why is the dirt not going into the dust bin? The rollers have been cleaned. It drops big clumps of dust and hair
roller probably has stopped turning best way to check is put on glass table and look under.
My sharky just grunts to move and stops? Wat could this be?
wheel or main brush motor
I have a new rv2520 the right wheel doesn’t work I’ve replaced the whole wheel and motor assembly and it still says error 2
Flashing two red lights
Hey man, I need to contact you, want to set up a business in my country
Whatcha mean?
My AI is having an instruction issue and nothing is wrong.!
! Comes out and stops woking
Check battery
Can you fix my robot ion?
Customer service told me it's the old model and they don't fix them anymore.
Contact info if u repair
Having problems with mine. The clean and exclamation light comes on. I already cleaned out, changed filter, checked the wheels. Please help!
Nancy Nguyen clean sensors with rubbing alcohol make sure bin is installed all the way.
Ours was doing the same thing I tried EVERYTHING finally I took my air compressor an cleaned the entire thing with it an the filter got in every crack an crevice an BOOM it worked again ... fyi it was flashing the red ! AN CLEAN good luck i hope this helps because we couldn't find ANY videos telling us what we could do to fix it
MoMoMain24 I just did the same thing and it worked. 👍🏻
@@ryanstreet2930 glad to hear it man I dont know why there isnt any videos on here about that