Shark Ion Robot Vacuum Wheel Repair
HTML-код
- Опубликовано: 6 окт 2024
- If you feel up to the challenge and want to save some money here is a great option to check before buying new wheels for your robot vacuum. This will save you time but is not always the problem.
Here is a list of the tools I use to work on these robots
Torx Bit Kit
amzn.to/3NugrU4
Rubber Mat
amzn.to/3PbrmU5
Grease for electronics
amzn.to/3N9e6gh
Cleaning Supplies
amzn.to/46630RB
New battery
shark iq
amzn.to/43nim2A
shark ion
amzn.to/43nim2A
Shark RV1001ae Spinner Brushes
amzn.to/2MsFZnP
Shark RV1001ae Brush Roller
amzn.to/3chvBKi
Shark Ion r85 (850) amzn.to/2Kne7wr
Shark Ion r72 (720) amzn.to/2YJBTMq
Shark Ion r75 (750) Refurbished amzn.to/2yBELML
Replacement Parts ebay.com/usr/s... 
Наука
I bought one on Prime day. Used it once and it wouldn’t re-dock. It had gone under the bed and a stray dryer sheet got stuck in the wheel housing. Your video saved me! Thanks so much!
Great video! One thing to add. Instead of pulling the pin out with pliers, I was able to push the pin out from the other side using my T15 torx.
Great detailed video, thanks. I used a small vise grip to remove the pin effortlessly.
Great video! Everywhere I looked it talked about replacing the entire wheel unit. Smitty's World took the time to dis-assemble the wheel unit. Mine was clogged just like this example.
So glad I was able to help you fix the robot and save some money in the process
Outstanding. Thank you. After seeing how much hair and crud was on the offending wheel I took the other one apart to clean it. Additional tools I recommend are a dental pick or paper clip and a toothbrush. I also found a lot of dog hair inside the wheel gear teeth which I removed with my dental lick and shop vac. Thanks so much. Seeing how this is built has made me happy. It’s a tank.
Picked a refurbished one of these. Had T9 screws past the pin. Thanks for run-through
Mine had T9 too
Thanks, mine had a Rolo just stuck right in there. Soaked all the plastics I could separate, hit everything else with isopropyl, then greased it back up. Works like new.
Thanks for the info! You’d think they’d seal these better since they’re advertising them as being great for pet hair.
When I pulled the wheel assembly out it had over a handful of hair packed in there. The gearbox wasn’t that bad.
I reassembled using a little rtv to seal the gear assembly
Thank You so much! This was our problem and it was a lsuper easy fix! Our shark has been "broke" for 9 months. 3 weeks ago I broke my hand and the sweeping by my 9year old or only once a week by my husband was driving me bonkers!
Is there anywhere I can purchase specific plastic gears or should I never buy a shark product again.
Thank you sosososososo much. I just got off the phone with the shark helpdesk and the guy told me my problem was "eletric" but that also that "there's debris in the model." asked him to clarify because eletric and debris isn't really the same thing and what did he mean by "model". He said I would either have to shell out a lot of money for a repair or just replace it. This video just saved me so much money and my favorite appliance! (I'm very attached to this vaccum! Its the only thing I wanted for Christmas years ago)
Thank you so much, I wish I would of seen your video before I bought a new one. I did take out the wheels and there was a lot of hair. I'll be using the old vacuum upstairs. I definitely recommend the shark over the more expensive brands.
I used this video to repair mine successfully. Very appreciated sir.
So many videos of people just replacing the entire wheel.
I will try this later today, thank for the information!
Take pictures as you go. Take dozens of photos from different angles. Even if "its just a quick little thing" or "something I can't possibly forget". Photos of every wire, lead and connection. Taking photos is easier and takes less time than learning how to read diagrams, schematics and blueprints.
Thanks for the video! I was ready to throw away our vacuum, but after watching this video I have our vacuum running like new again.
This video was great and just what I needed. Cleaned out it all out and the wheels spun great. Unfortunately, I severed a wire when I put one back in. Do you have a video on how to replace that? :)
There is a small cap on the end of the motor away from the gearbox. It covers an optical encoder (toothed cap + optical sensors) which tells the Shark's computer whether and how the wheel is moving. Very gently spread the clips, one side at a time, and pull the cover off. Ours had some hairs in it, which confused the sensor, so the Shark didn't think the wheels were moving. I blew the hairs out. If it happens again I'll use a tiny amount of RTV to seal the end cap.
That does happen I learned that after making this video it's pretty rare that happens but it does happen from time to time. I have also seen the end cap missing causing a bad wheel issue.
@@SmittysWorld hi do you sell right wheel unit for a MODELE: UR1105ARUS T3 14.4V --- 3.57A
Thank you, thank you, thank you! I have a shark IQ smart self-emptying machine that had a wheel that started binding up and this helped me solve problem.
Thank you for this video! It helped me greatly! Quick question… ever encounter a wheel where you can hear the gears?
I took my wheel assembly apart cleaned all the fur and hair out used some degreaser on all the gears reassembled with dielectric grease the gears spin very freely but when I put the motor in and the gears don’t spin. I am thinking the motor is bad. How can I get a motor without all the gears?
Thanks so much! Great easy to follow tutorial.
Hi Smitty, Great job on your RUclips about Shark Robot Wheel Repair! Do you have parts for sale? My left wheel gears are stripped. Please let me know.
No I stopped selling parts to many people scammed me out of money with ebay
I appreciate your video. I have a Shark AI robot model RV2520A0CA, S/N S31Q3081Z8H8. Following what you showed in your video, I took the left drive wheel assembly apart (left with the robot on the floor like it was going to clean with the front pointed away from me) and inspected it. The gears all look great. There were no chips or cracks and there was no hair inside at all. The motor spun freely when I spun it by hand. Even with all the gears removed, when I manually turn the wheel, it turns almost a full revolution and then seizes up. I can force it past that point but it seizes up again in the same spot on the next revolution. This causes the robot to throw a drive wheel error when you power it on to clean. Do you still repair these and/or do you still sell replacement parts? If I could ship you the drive wheel and you could fix it or if you could send me a replacement drive wheel, that would be excellent. Please let me know.
I can’t get the stupid pin out, any pro tips?
I had to keep slamming on it from both ends and eventually knocked it out
How do you remove the pin when it's flush with the housing it's in ?
I took apart my Shark robot vac Mod # UR1105ARUS as it was faulting for an obstruction. It seems that the right wheel is stiffer than the left. I took it apart, as per your excellent video but there wasn’t any debris(we do have 2 very hairy cats). Cleaned everything but it still shows the fault immediately. What is the cost of a (refurbished) wheel unit?
Is there any way to replace nylon gear A2 on Shark model 750?
I’ve done all of these steps. And my right wheel is still not spinning freely. It feels way more resistance than the left wheel. I’ve drowned it in quick dry cleaner, air compressor, lube, quick dry and it still feels like it’s too resistant. I think mine is tripping the error #2 because of the left wheel. It is still hard to turn. I added more lube.
@smittysworld Thank you for the video. I did everything you said but found no hair so I assume my motor is done for. Any tips on how to find the correct motor?
just got off the same model number and gear ratio the numbers on the motor itself doesn't have to do with anything
Hi which video Of yours has helped people catch the problem with the wheel so they do not need to buy a new one and instead can just repair it?
Great job
Where can I get the replacement motor I can't find it anywhere my motor has PRI-3655V-14175
Nice video... Mine robot would not drive straight. I took my right wheel apart and found the last gear that meshes with the wheel gear is stripped. Can I just buy the gear? Thanks in advance?
Message me on my ebay store
Do you have any similar video for Samsung Cyclone Force robotic vacuum clearner?
Your video for Shark Ion are very educational. Thank you.
No unfortunately I don’t have one to make a video on
My hair was inside the wheel FYI - there is a clip you pop off to get the wheel to back off - the hair is in there.
I need a right side drive wheel assembly for a RV1100VRUS. The electrical connector has a short in it.
CANNOT FIND A PART NUMBER.
Is it possible to remove the treads from the wheel? My wheel won’t spin very well even without the gears, so I’m thinking it’s an issue inside and I need to take the treads off.
I know this is late but I had to same problem and it was a snap ring you had to take off and clean the rod the wheel spins on and i got mine to spin well with out the gears
I have an error. Dock station is flashing blue, Max is flashing blue, Clean button is flashing red also explanation mark flashing red. Just would stop moving while slightly moving to the left. Thinking it's my left wheel.
Do you sell replacement parts for Shark QRobot?
Did all this and everything was pretty clean. I took a 9v battery and jumped it to the motor terminals and it ran fine. Plugged it all back in and it still doesn't work. Wires look fine. How do I test the main board?
Do you have any of the worm gears for a shark rv1001ae? So far best and like only video I could find on these wheel assemblies on these sharks
Message me on eBay and send me some pictures I probably dp
Question. I have a wheel that the spring mount broke off. Unfortunately all the screws to remove the wheel are stripped as I purchased a used unit. I was able to remove the spring without removing the wheel, so it is not an obstruction to the wheel. My question is; is the spring necessary? It seems to run fine without it.
It all depends on the model some will work just fine and some will throw a error code .If its working let it clean
Great video! thanks for the help, exactly what I needed to do.
i have rv750, but there's not 5 screws to remove the wheel unit. the entire bottom plastic is one complete piece. tried to take all screws off but, can't get the bottom off to access the wheel.
Where I can buy on set for 1 wheel? Mine has a broken one, the left one? Thanks for your help
I am trying to takeoff the wheel on my shark using your tutorial. It seems that two of the T5 screw wells are deeper than the other ones and I can’t get them to pull out. Is there a secret?
I'M LOOKING FOR A RIGHT WHEEL HOUSING FOR SHARK UR1000SR VACUUM. THE PLASTIC BROKE WHERE THE SPRING HOOKS TO THE HOUSING. IF YOU DON'T HAVE ONE, MAYBE YOU MIGHT HAVE AN IDEA WHERE I COULD GET ONE. IF YOU HAVE ONEPLEASE LET ME KNOW THE PRICE. THANK YOU, TOM
I enjoy your videos, thanks for help. I believe performing the cleaning process per the video, which mine had no debris or grinding or anything I could find I believe that it is the motor itself. Do you off the motors for RV1001AE model or would you now where I might be able to acquire them? Thank you.
Thank you... No hair in mine... Needed to lube the gear to stop the squealing
Hi, my Shark ran over a little bit of dog poo. I followed a video to take the wheels out, and I cleaned the Shark perfectly. I now get an error message every time I start it up saying there’s an obstruction. Sharks “customer service“ told me I need a new machine. They told me they would give me a discounted price on a new one for $100 more ($470, including shipping) than I bought this one for. Is there any other fix that you can think of? The vacuum is only a year and a half old. I really don’t want to buy another one after spending almost $400 on this one in such a short amount of time. Thanks!
Same thing happened to mine
So I have the a similar one, but inside that sprocket housing it was clean, but the wheel feels like it is binding alot. Is there a way to get the wheel off?
I have a Shark RV763 and cannot find a plastic gear in the wheel assembly that is damaged.
Could be a bad motor then.
My robot has the clean dock max and exclamation point blinking. It says it’s a drive wheel error. When it start it. It immediately turns right and then gets the error so I assumed the right wheel motor isn’t turning. Replaced the assembly and it is still doing the same thing. What could the problem be? Any help is appreciated
Maybe a wire broke or pulled loose. Maybe it's the other wheel? Maybe it's the drive circuitry on the main board.
@@scottwillis5434 never figured it out. Replaced the drive wheel. Inspected. No wires loose. No issues found. Threw it in the garbage and bought a roomba. Problem solved
So cleaned out my whole unit but there was no hair. Took out all the gears and greased them and the motor one, but when I assemble them they are tight and do not spin properly. The wheel spins easily without the gears and the motor spins easily without the gears too. Any recommendations?
remove the motor and spin it over see if there is some reistance.
@@SmittysWorld Do you have a video for that? HAHAHA
@@amandaweakley5919 what model robot do you have I don’t think so but naybe
@@SmittysWorld AV1010AE IQ
Thank you Man! Worked perfect for me!
Do you know where I can get replacement gears? I didn't see any on your eBay store. My gearboxes were full of dust, hair, etc and the teeth on the smallest drive gear are sheared off. It would be nice to buy a full set of replacement plastic gears.
I removed the wheel and a white gunk was on gears no hair no debris still prettty tight to move wheel i cleaned the gunk and now im thinking the gunk was grease? Put it back on and wheel is still hard to turn PLEASE HELP
So my motor seems fine, when I put all the plastic gears on, it will be stiff, is the middle gear that connects all of them bad?
I've got a 750 and 1 tires worn slick. I can't find the tire/wheel anywhere I also can't find the link to your store.
Great video! I was able to get the wheel out but the pin is flush with the casing so I can't grab it. Is there another way to get it out?
Opposite side of case you have to punch it out with a punch or screw driver and a hammer
@@SmittysWorld It worked! Thank you!!!
After all that, I was there was no hair in the inner case. However, the outer case was loaded with dog hair and some dryer sheet. Goblin is gobbling up the dirt once again. Thank you!
My three year old daughter fell on the robot and one of the wheels collapsed and no longer has that shock tension. Will replacing the wheel fix the problem or is there something additional to re-attach?
Replace wheel or fix the spring that broke off
Mine doesn’t want to wiggle so easily to come out after removing the 5 screws mine is a RV750R0US
T15 and T10 screws? What screw gun you use, link to HF cheap torx drivers.
Hey Smithy:-D I followed your video.... How can I buy just a gear wheel replacement? I have one that is stripped and it hasn't been easy finding a replacement on Google....
message me on ebay
sorry I meant how do I purchase these plastic gears
My ion robot shark RV750 is spinning in circles . Is there any reason why it’s happening ? Does it mean the wheels are damaged or do I need to replace it ?
Thanks!!
No problem!
Hello! How to remove last gearwheel and do full disassemble? Roborock S5 VMax.
Not sure I don't have one to take apart.
First off great video! I was able to declog both my side wheels in my RV850. Issue is now I can barely do a full run until they get clogged with hair again (I have 2 dogs)
Do you have any tips on keeping hair out of the wheel gear unit? Having to open up the wheel housing every run is more hassle than it’s worth.
Putting some thick grease in the wheel will help keep it out and sealing up the two half’s with a little rtv silcone
Thanks going to check my wheel now.
Do you have any wheels for a rv100ae? My right wheel was broken when I bought it and now the vacuum won’t work.
I’ve got a stripped gear A7 on my R750 and I cannot for the life of me find a replacement gear and I really don’t want to have to buy a whole new wheel assembly because of 1 gear.
750 or 750_N
Okay well mine still doesn't work and there's no motor grinding or noise 😅
Hey Smitty! Any chance you're still selling parts? Had to completely disassemble my AV2501S to fix the front wheel and somehow when putting it back together the wire harness broke off the right wheel motor. I think fixing it is beyond my capabilities. I'm having trouble finding a replacement wheel. You got one I could buy from you?
Sorry I don’t sell parts anymore. eBay is your best chance
I have a rv720 vacuum and one of the wheel assemblies quit working so I tore the whole vacuum apart and to get the wheel out on this model is nothing like any of the other you tube videos demonstrating how to remove it. I took the wheel assembly apart as well and noticed that the main gear on the wheel assembly was striped on the shaft. Not sure if there is a way to rig it to work or buy just the plastic gear. I'd think the easiest is to find a cheap vacuum being sold for parts but not sure if it is a common size gear through out all the models or specific to the 720. Any thoughts?
That’s gonna have same parts as a 700 robot 725 750 and 850 are different wheels come out from bottom.
Thanks for the video, by any chance do you have the wheels of the Shark RV750?, those are a little bit than the ones on this video.
No longer sell parts
I can't find your store on ebay and I don't know how to find your link. I need a replacement for a shark robot vacuum 5 wire set.
Where do i buy replacement wheels for the 750? The gears are so damaged in my one wheel from my baby riding it the vacuum just goes in a circle.
Link to my eBay store is in the description
No hair in mine I need a replacement but can’t find one
message me on ebay I might have some parts depending on the model
@@SmittysWorld I haven’t been able to log in to eBay ? It’s model AV1110ARUS
Any chance you sell the little gears in the wheels? I was able to clear the jam, but it looks like the smallest gear in my wheel is stripped.
Yes I do message me on eBay I’ll check later tonight if I have any . Send me pictures of the one you need and model info
Smitty, Do you know what the cable connecting the wheel motor to the main board is? It's a 6 pin connect but I don't recognize it as JST or SM
Sadly it’s custom to shark from what I can tell but I do sell them
Very helpful. Thanks.
What if wheel comes off track.
Replace full assembly
Some of the screws to remove the wheel seem to be stripped and cant get them out, any other solution?
you can drill them out then remove them with pliers after wheel comes out but have to be carful
I bought t-10 and t-15 from harbor freight. Well got wheel out as you shown with t-15. Then tried to get the wheel cover off with t-10 and was to big. Any suggestions?
Different models require t-8 t-9
I took my wheel housing apart. Gears looked great. There was something in between the wheel and the housing. Took it out. Motor, wheel gears move. Turn it on drive error still pops up. Any ideas?
Keep breaking it down until you find out which part has the excessive drag in it, or spot the junk causing the drag.
I have just gotten one step closer to being the smartest man on Earth
Looks like my wheel bracket is broken. Do you have anything coming up in your ebay store?
Send me a email smittysworld2015@gmail.com
Your link to your ebay shop doesn't work. Do you have a refreshed one or have you stopped selling parts for these?
I no longer sell parts to many people tried to scam me
@@SmittysWorld I get it. Your video was super helpful though. Just found out I need a new wheel motor because of it. I hope you'll keep posting informative vids. Keep your head up man. 👍🏾💪🏾
I have an RV1001AE are the wheels the same as the other models? Having trouble finding for that specific unit
They are only the same for 1001 series . I have some listed on my eBay store
Can I buy just the gears? The plastic gears in mine were worn out.
Send me a message on eBay I’ll see if I have any laying around
Hey smitty I need the same but specific the 2nd from the wheel side would be nice to have a complete set if you have some let me know
how do I locate the plastic gears in my UR1100 wheel drive gear?
Take the wheel apart like this it's a little different but very similar.
Hi! Can you please tell me if I can take the wheel a part to clean it for the RV1001AE. I open it but still fill kind of hard. I am not able to take the wheel out.I am bot sure if that is possible
Have the rv 1001ae. Got the wheel off. The inside screws are not T10. The pin is different. Did you figure it out?
I have a slight issue for my vacuum where one of the gears is broken on it
what gear
I’ve watched several videos and everything seems to be checking out but it’s still making this awful screeching noise anytime it goes to clean. Any ideas?
You check main brush roller motor
Ok so I have now 2 robots and 3 bases, because shark for doesnt send out parts! I need two drive wheels please
Hi Smitty, what is the name again and where can i get those two type of screw dirvers? -Thanks!
Torx bit and you can get them at harbor freight Lowe’s and Home Depot even Walmart should have them get get a set t9 to t25
Will need t10 and t15
Your're the best thanks! Wish me luck my tire is stuck and won't move hoping to open and just find debris to clean by following your video!
@@andie1584 hopefully that helps I would just get a set of torx drivers long shafted just in case they are different size I have seen two with different size screws but all have been between t9 and t20
funny that you mentioned that, I was able to take all the screws except for one, it had to be the one that is allll the way at the bottom :s feel like its different size, now that you mentioned it, it makes sense, so i think am gonna hold off and buy the torx set your suggesting
Does anyone know if the pin on the 900 series wheel is removable? I've been trying to get mine out but I can't get it to budge.
Should be but pain to remove
Hm yeah I feel like I'm gonna break this thing before I get the pin out. Before I break it, do you know where I might be able to buy a new wheel + housing for the 900 series?
@@jacobharvey6809 send me a email at smittysworld2015@gmail.com with some pictures of the wheel and robot I’ll see what I can find maybe give you some help
ok we took the wheel apart down to the gears and they were pristine with lots of white grease. Now what???
Do you have a way to test the motor
lol put it back together twice, and now it works, the fool thing! =)
@@annmarin3304 great to hear