So glad we got a smooth criminal like this geezer giving us tips for the trade 27 years of age and 12 years into the game and still learning and enjoying it Big up the plumb bwoiiis Safee
Got my NVQ level 2 in plumbing but it was a full time course of 2 days!!.. completed it in 2 years at age of 18 but couldn't get apprenticeship to do NVQ level 3. Now 15 years later want to get back into it. But will need to start from scratch probably do a refresher course too. Top video
Haha, when I was an apprentice, my mentor threw me a lump hammer and a chisel to chase in the kitchen hot and cold on the fisrt fixes. I realised until months later he had an angle grinder and sds chisel in his van that he used when he had to do it.
I just bought a Worcester 38cdi and I'm fitting it to my bungalow. Massive open loft and I'm laying all the radiator pipework down myself. Your videos have been very helpful mate :) ... (was all storage radiators, so its an easy, brand new fit)
About to renovate shower room. Need to bury hot/cold feeds. Probably gonna use the gaffer tape trick then use some bonding to cover before tiling over. Wish me luck!
Would you worry as much about the screed eating the pipe if you used plastic pipe in the wall cavity? Also would you still need to insulate the pipe if it's barrier pipe??
James if you have to use copper you could always use 15mm Wico and nail clips you wouldn’t need to chase so deep.Maybe your using lagging because of expansion in the central heating pipes love to hear your opinion.
Please be aware the correct method for wrapping pipes in screeds and plastered walls is to wrap them in Denzo tape when advising other non plumbing professionals , as the content of either gypsum or cement will corrode any copper pipe work .please note I am a plumbing lecturer and have been a gas engineer for over 30 years.
I accidentally drilled through a copper water line in my 1946 year double brick house. The pipes are located in a chased channel filled with cement based mortar/plaster. When I removed bricks and mortar to expose damaged fragment the copper pipe was like installed yesterday with no any corrosion. May be Australian cement is different, I don't know....
ayla un yep....Approved Document A (structure) states max depth of 1/3 of the masonry so for 100mm block 33mm depth chase. Vertical chases to be 1/6 the depth, so 16mm. That’s the Regs. Period houses have plaster depth of 25mm usually and modern homes have plaster dabs at varying thickness, max 25mm.
Cool video as usual , but tell for copper pipes in concrete they to use a sticky tape call demzo or is that a thing of past or am showing my age and also in US they just put plastic sleeve on top of copper pipes is that something we can do in UK?
Something you might have not known but "Duct trap" has metal in it which in the long run will cause electrolysis with the copper, Some inspectors in Canada wont pass.
I certainly didn't know that! But aluminium is less noble than copper so I don't think it would really be anything to worry about even if the % Al in the tape were not negligible. Maybe a chemist can advise.
Hi mate, great vid. Quick question, I have chased two pipes in the wall like this, but not as deep, chased about 20mm depth out and about 40-50 mm wide and installed 10mm pipe. Can I clip them and tape them with gaffa like in this vid and just plaster over or should spray small amount of foam over pipes before plaster.. Thanks
I would have chisseled out closer to the corner if some one wants to hang a picture it's looks like they might drill in to pipe depending on fixing, good job asusall 👍🏽
Hey, I paid a plumber £5k to install new boiler and radiators (not supplied by them). They have chased plastic pipes into the walls and said it's the best option (due to expansion) but they also haven't insulated them and currently they aren't flush. The quote says they wouldn't 'fill in' the chases but surely they should be insulating them and ensuring they're flush?
Loving your plumbing videos! I could almost contemplate chasing my own pipes in.. however they do at least give me an idea of how the work should be done (insulated etc). Am now looking for a local plumber to do the work. If I was tackling exactly the same task as in this video (including the chasing out, pipe laying, insulation and radiator installation (already purchased) - could anyone give me an estimate of a 'reasonable quote'?
Nice video mate, being a plumber/gas trainee, you've given me some great tips. Funnily enough I was doing this in my kitchen and 40mm down in the screened floor was the heating pipe, 10mm down more was my cold water main! What's the chances of that haha. Keep up the good work! Hold tight
Very informative videos. Need a little help if possible. I am currently in the process of doing my kitchen. The cold water feed is in this room so will supply everything then go upstairs and hot water will come from upstairs down to for sink ect. I planned to do exactly as you have and chase the wall out for the pipes. I was going to use 15mm copper can I use the exact same method as you have using insulation ect or does it need to be done different as it is hot and cold water? Thank you
Hi mate great video I'm.not a plumber can you shed some light and what I'd be looking at if I done the chasing (firmer brickie who does odd jobs ) for 2 rad pipes 2 water supply pipes for sink and if allowed a gas pipe to be put into a recess for a clean finish ? Thanks
Could you do the same with poly pipe? Also could it be done so that the pipes come from the wall above the skirting? I need to move a radiator and it is going onto a wall where there is parquet flooring and really don’t want to disturb it if I don’t have to. Any help greatly received
When chasing pipes in, are new pipes required or can existing pipes be used? Also what about when re-plastering the room anyway? Looking at purchasing a property with back boiler and pipes on show so trying to figure out how much needs spending!
Great vid! About to do the same job with a single pipe c/w supply to the loo cistern. Is it OK to fill the channel around the pipe with expanding foam, instead of render. Does it effect the copper pipes? It's going to be tiled over, so doesn't need a plaster finish.
I’ve got a newly qualified plumber re re routing my kitchen pipes. I would like the hot and cold pipes chased into one of the walls . He’s trying to tell me the walls are too brittle to do this. Is he spinning me a line and just doesn’t want to do it. It’s thermalite block behind my plaster board
Like your vids mate but not sold on this one I'm afraid! You used to have to cover copper in walls due to lime in plaster which eats into copper, that is no longer the case. With the insulation the plaster is guaranteed to crack. better option in my opinion is to use plastic pipe, but either way spray with expanding foam then plaster on top a much firmer backing for plaster, prevents material getting to pipes and insulates
Hi there, it's great you live our videos! I've personally never had a problem with any of the methods as long as you've got a nice deep chase. But we'll see!!! Many thanks, PP!
hi, im currently renovating my house, im going to fit a combi in the loft and re pipe the house, i noticed my friends new build is piped in 10mm plastic is this ok or should i use 15mm plastic, im going to chase it in the wall also, its a 4 bed house and its in microbore at the minute, love your how to's they are very helpful. thanks
Hi there. You can use 10mm plastic if it makes it easier to hide in the wall. However always try to use 15mm if you can! Especially on runs of more than one radiator. After three rads on a single run you need to use 22mm. Good luck mate! SUBSCRIBE! ➡️👉 ruclips.net/user/plumberparts 👈⬅️ IF YOU HAVEN'T ALREADY! 😎
Howdy, I was wondering what your opinion was on having exposed copper pipes in the bathroom. I want to do up my bathroom, take out the bath tub and put in a walk in shower. But I don't want the to break or chisel down the wall just to hide pipes, I just don't want them to damage the brick or concrete or destroy the wall. So I was thinking of just extending the pipes from the bathtub which is removed, having exposed copper pipes and just putting shower and tap fittings. I heard that lather can be applied in order to keep the copper pipes looking great. I am not sure if they make plastic coverings that clip on like the ones they make for electrical cables to hides tv cords , so you don't have to chisel down the wall. What's your opinion?
hi, i want to have wall mounted showers in my bathroom, the wall is a cavity wall and its the supporting wall. is it possible to trace pipe work on such wall or i have to build false wall? thanks
Correct. Well it's not the pipe which is the problem. It's the fittings. Pipes should be removable at both ends under a floor screed So he could have done this using only a bender
Help! I bought 2 flexible pipes that have that skinny m10 end for kitchen taps but my taps are a bigger(maybe 1/2") male end not female. Can I buy something to adapt them?? I need it to look like the wider female bit at both ends. I would just buy one but mine are 120 long and can't find something that long in wickes
nice work it should be better if you chisel the wall on the left hand side better then the middle just in case if they want to hung something in the wall they hit your pipe
For my shower, I have concealed pipes into a solid wall. My builder didn't do a good job which made the tiles crack and pop out of the wall. Now having to do it again! The pipe is plastic coming from floor to the control valve. Then copper pipe from control valve to shower head. Does it only need insulation on copper pipe and also the plastic?
Is it the same principle when using plastic push fit pipes? Does it still need protection from the screed and plaster? Just subbed. Great Chanel. Thanks
i just had some plumbing work done . simpler to the video you just shared but i noticed that theres a considerable amount of heat coming thru the wall. is that normal
wouldn't it be better to hang and position the radiator before soldering the vertical sections which go into the valves? How can you be sure that your short vertical pipes will go exactly into the radiator valves?
Great vid, terrible signing! Less tricky if you apply the duct tape before offering the pipes up to the wall though. My need for watching the vid was to see how you finish the holes from the floor to the rad,
Geeza as always top vid would have looked amazing if pipes came out of the wall instead of the floor. Can you do a vid on under floor heating does and don't.
So ar people paying for this kind of work in the UK? Im a plumber to, I mean, you are using copper, soldering it and works with a angle grinder. Here in The Netherlands we will work with alupex tube and a wall cutter, we can arrange this job within one hour without the use of a pipe bender and soldering materials. And you can chase alupex directly in the wall without any use off protection just plaster. So it will be much cheaper. Dont you guys use this in the UK? Please let me know.
So do you have 100% guaranty you will not have a leak and having to take the insulation to mend the leak?? Test first and then insulate and tape pipes??!!
A crack appeared later in the wall above as one half of the house moved away from the other due to the slot created by the plumber and the only thing retaining the houses together was the gaffer tape... 😆
Do you just fill the wall now with some 'cement' type substance or would you pre-fill some of it with that foamy stuff first? It must be a hell of a job to fill in, and then plaster?
Cement and skim. Some use newspaper to protect the pipes. Or fixer foam to fill the gap, cut back and skim. SUBSCRIBE! ➡️👉 ruclips.net/user/plumberparts 👈⬅️ IF YOU HAVEN'T ALREADY! 😎 Reply ·
I'm having a vertical radiator installed on my wall, the corgi who came to install it chased up the sides of the chimney breast where I am having it installed but he didn't pin the pipes to the wall. I meant to be having plaster boarding over the chimney breast but was he meant to pin these pipes? He just wrapped the pipes in black tape I guess to insulate them? Is the plasterer meant to pin these pipes or was the corgi meant to do that?
@@gooffey81 Hi Stephen thanks for this. My plumber has ripped me off. We told him to install the radiator ready for the pipes to be boxed in, he now claims we didn't ask for a 1st fix and also claimed that he didn't need to pin them in. I am not sure what to do as I lost £260 over it. His pipe work looks good but then again just left these two long pipes dangling about with the TRV's attached. I may have to get another plumber out now to rectify it. He just installed it to the chimney breast as in not a first fix and made out that we didn't ask for a 1st fix when it's pretty clear that we are having plastering done. He insisted that the plasterer can just plaster around the pipes and doesn't need to pin them which won't work because the TRV valves won't sit flush when boarded in, (having them pinned in probably makes the plasterer life easier since he will then know where to board and plaster the pipe work) pipes should be coming out of the chase about another 2 or 3 inches for room to play with which been told by a plasterer that the pipes either side should of been longer for extra play when we come to mount the rad back on the wall, then cut the pipes to length to marry up with the rad valves. Just lazy shoddy work, should I report him? Now he wants £60 to come back out and refix the issues and then the rad comes off the wall, brackets ect to get it all boxed in with plasterboard. Then he wants another £85 to come back and remount the radiator, redrill screws for brackets, refit them and test the radiator again when it's already been tested.
Installing pipes to a radiator or plumbing appliances is all part of a first fix. Pipes should never be left loose. They should be clipped to a wall or knock over clips on joists. This can prevent the pipes from rattling..Sometimes they can get really loud when a heating system is running. The only reason to leave them loose on a first fix is to plaster behind them. I hope he's put cap ends on the TRVs (thermostatic radiator valve)? TRVs can open up when a heating system starts. That's how we go about every job. Good luck
*Links to the tools I use everyday here:* www.amazon.co.uk/shop/plumberparts
Plus, follow my *Vlog “TimesWithJames”:* ruclips.net/user/timeswithjames
So glad we got a smooth criminal like this geezer giving us tips for the trade
27 years of age and 12 years into the game and still learning and enjoying it
Big up the plumb bwoiiis
Safee
Got my NVQ level 2 in plumbing but it was a full time course of 2 days!!.. completed it in 2 years at age of 18 but couldn't get apprenticeship to do NVQ level 3. Now 15 years later want to get back into it. But will need to start from scratch probably do a refresher course too. Top video
The way I chase pipes into a wall is in the Carry on 'arse slap' style, then chase them round the room and into the wall. Works every single time.
Haha, when I was an apprentice, my mentor threw me a lump hammer and a chisel to chase in the kitchen hot and cold on the fisrt fixes. I realised until months later he had an angle grinder and sds chisel in his van that he used when he had to do it.
Ouch - that's mean! Brutal for you and too stingy to buy a new angle grinder blade.
I just bought a Worcester 38cdi and I'm fitting it to my bungalow. Massive open loft and I'm laying all the radiator pipework down myself. Your videos have been very helpful mate :) ... (was all storage radiators, so its an easy, brand new fit)
Glad to help!
About to renovate shower room. Need to bury hot/cold feeds. Probably gonna use the gaffer tape trick then use some bonding to cover before tiling over. Wish me luck!
Same me mate!
Brilliant video mate. Exactly what I was looking for.
Could use expansion foam to insulate the pipes?🤔.
pvc pipe doesn't need insulation?
Red rawel plugs are for sparkies!!
Great video! If I am using plastic pipe to bury into a wall for a shower do I need to insulate them? And where would I place the shut off valves?
Would you worry as much about the screed eating the pipe if you used plastic pipe in the wall cavity? Also would you still need to insulate the pipe if it's barrier pipe??
I thought plastic was an obvious choice too
Are 15mm pipes to much to plaster over if there just against red brick? Would it just crack the plaster further down the line
James if you have to use copper you could always use 15mm Wico and nail clips you wouldn’t need to chase so deep.Maybe your using lagging because of expansion in the central heating pipes love to hear your opinion.
Please be aware the correct method for wrapping pipes in screeds and plastered walls is to wrap them in Denzo tape when advising other non plumbing professionals , as the content of either gypsum or cement will corrode any copper pipe work .please note I am a plumbing lecturer and have been a gas engineer for over 30 years.
+James Hemsworth Hi James, thanks for your comment!
Sub here please>> ruclips.net/user/plumberparts
+1. Been to a few pinhole callouts where pipework under screed was wrapped in gaffa lol. Flooring ruined, nice big bill.
I accidentally drilled through a copper water line in my 1946 year double brick house. The pipes are located in a chased channel filled with cement based mortar/plaster.
When I removed bricks and mortar to expose damaged fragment the copper pipe was like installed yesterday with no any corrosion.
May be Australian cement is different, I don't know....
When so much of structure is cut doesn't it make the walls weak? I ask because plaster is only 10mm so you must be cutting brick/block.
ayla un yep....Approved Document A (structure) states max depth of 1/3 of the masonry so for 100mm block 33mm depth chase. Vertical chases to be 1/6 the depth, so 16mm. That’s the Regs.
Period houses have plaster depth of 25mm usually and modern homes have plaster dabs at varying thickness, max 25mm.
No James didn't worry as the gas leak he left blow the bulding up
Way too deep
Cool video as usual , but tell for copper pipes in concrete they to use a sticky tape call demzo or is that a thing of past or am showing my age and also in US they just put plastic sleeve on top of copper pipes is that something we can do in UK?
Something you might have not known but "Duct trap" has metal in it which in the long run will cause electrolysis with the copper, Some inspectors in Canada wont pass.
+Derek R (dRykenTV) Hmmm ok, good info!
I certainly didn't know that! But aluminium is less noble than copper so I don't think it would really be anything to worry about even if the % Al in the tape were not negligible. Maybe a chemist can advise.
Can you chase plastic piping? If so, does it need protecting like the copper pipes?
Hi mate, great vid. Quick question, I have chased two pipes in the wall like this, but not as deep, chased about 20mm depth out and about 40-50 mm wide and installed 10mm pipe. Can I clip them and tape them with gaffa like in this vid and just plaster over or should spray small amount of foam over pipes before plaster..
Thanks
Outside Wall You Must Have Mild Winters. This Would Be A Freezing Problem In Northern Climates Even With Glycol. Nice Work!
Cheers!
Do you have link to the next vid, when your colleague screeds / fills over the pipe?
I would have chisseled out closer to the corner if some one wants to hang a picture it's looks like they might drill in to pipe depending on fixing, good job asusall 👍🏽
Hey, I paid a plumber £5k to install new boiler and radiators (not supplied by them). They have chased plastic pipes into the walls and said it's the best option (due to expansion) but they also haven't insulated them and currently they aren't flush. The quote says they wouldn't 'fill in' the chases but surely they should be insulating them and ensuring they're flush?
I've seen some plumbers use white pvc pipes and chasing it in. Is that ok to do instead of copper pipes?
Loving your plumbing videos! I could almost contemplate chasing my own pipes in.. however they do at least give me an idea of how the work should be done (insulated etc). Am now looking for a local plumber to do the work. If I was tackling exactly the same task as in this video (including the chasing out, pipe laying, insulation and radiator installation (already purchased) - could anyone give me an estimate of a 'reasonable quote'?
Do solvent weld wastepipes need sleeving/protecting when burying in screed?
No it's plastic. The reason for taping the pipes in the video is that concrete or plaster corrodes the copper over a period of time
Nice video mate, being a plumber/gas trainee, you've given me some great tips. Funnily enough I was doing this in my kitchen and 40mm down in the screened floor was the heating pipe, 10mm down more was my cold water main! What's the chances of that haha. Keep up the good work! Hold tight
No worries Sam, glad to help!
What are the options if the pipe coming out of the wall are not long enough for the new shower?
I'm looking at doing this in my house. Will a double skimmed brick wall in a victorian house be deep enough gouge out a decent chase for them?
Very informative videos. Need a little help if possible. I am currently in the process of doing my kitchen. The cold water feed is in this room so will supply everything then go upstairs and hot water will come from upstairs down to for sink ect. I planned to do exactly as you have and chase the wall out for the pipes. I was going to use 15mm copper can I use the exact same method as you have using insulation ect or does it need to be done different as it is hot and cold water? Thank you
Hi mate great video I'm.not a plumber can you shed some light and what I'd be looking at if I done the chasing (firmer brickie who does odd jobs ) for 2 rad pipes 2 water supply pipes for sink and if allowed a gas pipe to be put into a recess for a clean finish ? Thanks
These vids are so good I might cancel my Netflix subscription
So good looking
you're a riot mr Plumber! subscribed!
Quick question about insulation, why 15/13 and not 15/9? it's more compact, does the same thing and it's cheaper:)
My friend, you are a good teacher.
Scheut Cheers!
Could you do the same with poly pipe? Also could it be done so that the pipes come from the wall above the skirting? I need to move a radiator and it is going onto a wall where there is parquet flooring and really don’t want to disturb it if I don’t have to. Any help greatly received
When chasing pipes in, are new pipes required or can existing pipes be used? Also what about when re-plastering the room anyway? Looking at purchasing a property with back boiler and pipes on show so trying to figure out how much needs spending!
Great vid! About to do the same job with a single pipe c/w supply to the loo cistern. Is it OK to fill the channel around the pipe with expanding foam, instead of render. Does it effect the copper pipes? It's going to be tiled over, so doesn't need a plaster finish.
I’ve got a newly qualified plumber re re routing my kitchen pipes. I would like the hot and cold pipes chased into one of the walls . He’s trying to tell me the walls are too brittle to do this. Is he spinning me a line and just doesn’t want to do it. It’s thermalite block behind my plaster board
Any reason you didn’t or wouldn’t use Speedfit pipes ?
Like your vids mate but not sold on this one I'm afraid! You used to have to cover copper in walls due to lime in plaster which eats into copper, that is no longer the case. With the insulation the plaster is guaranteed to crack. better option in my opinion is to use plastic pipe, but either way spray with expanding foam then plaster on top a much firmer backing for plaster, prevents material getting to pipes and insulates
Hi there, it's great you live our videos! I've personally never had a problem with any of the methods as long as you've got a nice deep chase. But we'll see!!! Many thanks, PP!
Denzo ftw
Makes sense... but both methods look neat.
Can you not use a roll of plastic save on potential joints /leaks ?? Would it be OK with render ??
hi, im currently renovating my house, im going to fit a combi in the loft and re pipe the house, i noticed my friends new build is piped in 10mm plastic is this ok or should i use 15mm plastic, im going to chase it in the wall also, its a 4 bed house and its in microbore at the minute, love your how to's they are very helpful. thanks
Hi there. You can use 10mm plastic if it makes it easier to hide in the wall. However always try to use 15mm if you can! Especially on runs of more than one radiator. After three rads on a single run you need to use 22mm. Good luck mate! SUBSCRIBE! ➡️👉 ruclips.net/user/plumberparts 👈⬅️ IF YOU HAVEN'T ALREADY! 😎
ahh i see thanks, so out the boiler in 22mm then T off in 15 to all the rads, i have 13 is that correct?
thanks for your help
So this tape you stick on, would it’s condition change due to the pipes getting hot, and how long can it last with the pipes?
Do you recommend insulating cold water pipes to protect pipe from concrete?
I see you use mapp gas for soldering, not propane. Is there a reason for that, or is it just what you had on hand?
It's what I had to hand mate. I do find mapp is a little hotter too! Cheers for your continued interest in the channel! You should get a sticker!!!!
Great Video , having to deal with this now from the sink.
Please be carefully those old vinyl type tiles can contain asbestos ,so not a good idea breaking them up
This video is great! Thanks for the advice and nice singing there ;)
Howdy, I was wondering what your opinion was on having exposed copper pipes in the bathroom. I want to do up my bathroom, take out the bath tub and put in a walk in shower. But I don't want the to break or chisel down the wall just to hide pipes, I just don't want them to damage the brick or concrete or destroy the wall. So I was thinking of just extending the pipes from the bathtub which is removed, having exposed copper pipes and just putting shower and tap fittings. I heard that lather can be applied in order to keep the copper pipes looking great. I am not sure if they make plastic coverings that clip on like the ones they make for electrical cables to hides tv cords , so you don't have to chisel down the wall. What's your opinion?
Use stainless, looks ok.
hi, i want to have wall mounted showers in my bathroom, the wall is a cavity wall and its the supporting wall. is it possible to trace pipe work on such wall or i have to build false wall? thanks
+ice lam Should be fine. Just make a channel in the cavity, install your pipework then cover and seal as normal.
great video i am just doing this exact job in our living room. many thanks for the tips. and video great slo mo for those not experienced keep it up.
As per water regs ‘No water fitting shall be embedded in any wall or solid floor’ - Schedule 2: paragraph 7 explained G7.1B
I didn’t think regs allow for screeding over pipes any more. I thought everything has to be ducted or boxed in?
Correct. Well it's not the pipe which is the problem. It's the fittings.
Pipes should be removable at both ends under a floor screed
So he could have done this using only a bender
Help! I bought 2 flexible pipes that have that skinny m10 end for kitchen taps but my taps are a bigger(maybe 1/2") male end not female. Can I buy something to adapt them?? I need it to look like the wider female bit at both ends. I would just buy one but mine are 120 long and can't find something that long in wickes
Hi mate Can u please tell where or how I can get a 6mm bore flexi tap tails
How did your mate chase that out so neat?
Was there a reason for not chasing the horizontal runs of pipes into the wall?
nice work it should be better if you chisel the wall on the left hand side better then the middle just in case if they want to hung something in the wall they hit your pipe
amario anas Bear that in mind for next time!
For my shower, I have concealed pipes into a solid wall. My builder didn't do a good job which made the tiles crack and pop out of the wall. Now having to do it again! The pipe is plastic coming from floor to the control valve. Then copper pipe from control valve to shower head. Does it only need insulation on copper pipe and also the plastic?
insulate everything - it all loses heat! (unless its a cold water service)
Good call Benjy! SUBSCRIBE! ➡️👉 ruclips.net/user/plumberparts if you haven't already!
Nice video mate, how did use test the pipe work under the floor?
+Alexander Lamond Pressure test? Standard way with an air pump.
Do plumber have piping routes like sparks have cable routes, so to avoid drilling or cutting into the walls where there’s pipework ???
Not as strict as sparks route but plumbers should run everything vertical or horizontal
Hey jolly fellow...Do you have any videos on how to remove galvanized pipes from walls and replace with PEX ?
building reg...Vertical chases should be no deeper than one third of the wall thickness!
And they aren't in this video! Sorry for the delay in replying!
Sub here please➡️👉 ruclips.net/user/plumberparts 👈⬅️If you haven't already!
Is it one third 'wall' thickness or 'leaf' thickness?
Leaf.
I'm in the north east uk. Need rad pipes hidden in 3 rooms. How much should I expect to pay a plumber to do this?
Pipes come down from ceiling then along skirting to rad.
Is it the same principle when using plastic push fit pipes? Does it still need protection from the screed and plaster?
Just subbed. Great Chanel. Thanks
Yes mate!
plumberparts hi what should be used as a heat shield
i just had some plumbing work done . simpler to the video you just shared but i noticed that theres a considerable amount of heat coming thru the wall. is that normal
+Abi Rotimi Yeah it will be normal.
WHY DIDN't you test for any leaks before covering with foam insulation. How would that be done. thanks
soon find out when water is in them.....
wouldn't it be better to hang and position the radiator before soldering the vertical sections which go into the valves? How can you be sure that your short vertical pipes will go exactly into the radiator valves?
+Aman A Because I'm a legendary plumber.....and I'm lucky! PP!
+plumberparts ;-)
I'm not a plumber and just bonded straight over the bare pipes coz I'm a fuckin gangster. 12 years later still going strong
Great vid, terrible signing! Less tricky if you apply the duct tape before offering the pipes up to the wall though. My need for watching the vid was to see how you finish the holes from the floor to the rad,
Geeza as always top vid would have looked amazing if pipes came out of the wall instead of the floor. Can you do a vid on under floor heating does and don't.
kuli557 I will!
How much should a job like this cost roughly?
nice neat work good job
journeyman plumber here
i know everyone would have their own ways of doing it especially my boss lol..
Can you please make video on how to pressure test pipes with standard air pump. Many thanks
Will do!
Arbeed Ahmed ?
+plumberparts where is the video ?
Thanks
+plumberparts I didn't know that was an option. Looking forward to the vid.
I love the videos to, but I thought that the Water Regs didn't allow pipework on external walls? Thoughts anyone? Keep up the good work!
Hmmm might be if it's single skin perhaps. Otherwise I've seen it in nearly every property I've worked in! Regards, PP!
Nice job
Ps loving the videos mate , keep up the good work 😁
love the videos keep them coming
Cheers dude!
So ar people paying for this kind of work in the UK?
Im a plumber to, I mean, you are using copper, soldering it and works with a angle grinder.
Here in The Netherlands we will work with alupex tube and a wall cutter, we can arrange this job within one hour without the use of a pipe bender and soldering materials. And you can chase alupex directly in the wall without any use off protection just plaster. So it will be much cheaper. Dont you guys use this in the UK? Please let me know.
+Mar Cel I think its called something else over here. Use it on Uponor..
is expanding foam ok to use touching the copper pipe?
Yep fine
I thought that expanding foam corrodes copper.
So do you have 100% guaranty you will not have a leak and having to take the insulation to mend the leak?? Test first and then insulate and tape pipes??!!
A crack appeared later in the wall above as one half of the house moved away from the other due to the slot created by the plumber and the only thing retaining the houses together was the gaffer tape... 😆
trunkimg barrier pipe ?
Why did you not just stick the rad tails out the wall?
I'm sure the client isn't going to come back and render the wall either.
He bloody better! He owns the home and wanted the pipes in the wall!
And here was me thinking the "chase" was the cutting/drilling job. So it's actually just the fitting part. Every day's a school day.
At these work speeds It takes months to install a few radiators
Do you just fill the wall now with some 'cement' type substance or would you pre-fill some of it with that foamy stuff first?
It must be a hell of a job to fill in, and then plaster?
Cement and skim. Some use newspaper to protect the pipes. Or fixer foam to fill the gap, cut back and skim. SUBSCRIBE! ➡️👉 ruclips.net/user/plumberparts 👈⬅️ IF YOU HAVEN'T ALREADY! 😎
Reply ·
I want to put a picture up where those pipes are wheres my Drill
GETTHEDEUCE loool
Pp if u had a rad schedule u would win d lottery!!
And make D'movie!!,
Centra of wall was that important choice? Obvious a picture will be hung there, nail straight into pipes
I'm having a vertical radiator installed on my wall, the corgi who came to install it chased up the sides of the chimney breast where I am having it installed but he didn't pin the pipes to the wall. I meant to be having plaster boarding over the chimney breast but was he meant to pin these pipes? He just wrapped the pipes in black tape I guess to insulate them? Is the plasterer meant to pin these pipes or was the corgi meant to do that?
The plumber should do it. It's his job, not the plasterer.
Unless the plasterer removes them which they are buggers for
@@gooffey81 Hi Stephen thanks for this. My plumber has ripped me off. We told him to install the radiator ready for the pipes to be boxed in, he now claims we didn't ask for a 1st fix and also claimed that he didn't need to pin them in. I am not sure what to do as I lost £260 over it. His pipe work looks good but then again just left these two long pipes dangling about with the TRV's attached. I may have to get another plumber out now to rectify it.
He just installed it to the chimney breast as in not a first fix and made out that we didn't ask for a 1st fix when it's pretty clear that we are having plastering done. He insisted that the plasterer can just plaster around the pipes and doesn't need to pin them which won't work because the TRV valves won't sit flush when boarded in, (having them pinned in probably makes the plasterer life easier since he will then know where to board and plaster the pipe work) pipes should be coming out of the chase about another 2 or 3 inches for room to play with which been told by a plasterer that the pipes either side should of been longer for extra play when we come to mount the rad back on the wall, then cut the pipes to length to marry up with the rad valves. Just lazy shoddy work, should I report him?
Now he wants £60 to come back out and refix the issues and then the rad comes off the wall, brackets ect to get it all boxed in with plasterboard. Then he wants another £85 to come back and remount the radiator, redrill screws for brackets, refit them and test the radiator again when it's already been tested.
Installing pipes to a radiator or plumbing appliances is all part of a first fix.
Pipes should never be left loose. They should be clipped to a wall or knock over clips on joists.
This can prevent the pipes from rattling..Sometimes they can get really loud when a heating system is running.
The only reason to leave them loose on a first fix is to plaster behind them.
I hope he's put cap ends on the TRVs (thermostatic radiator valve)?
TRVs can open up when a heating system starts.
That's how we go about every job. Good luck
Is that a rothenberger access chair ? Haha
antthebear If only, couldnt afford it! :)
Would the plasterers bonding take to the insulation I alway use gaffer tape or if it’s a Friday FUCK ALL HAHA
Very Cool
+Plumbers In Your Area Cheers dude!
Nice
Can't run plumbing in outside walls in Canada so I don't need to worry about ever doing this
word up