So I've done quite a few analog and shell swaps with joycon and have a few tips. 1: You don't need the guitar pick. The plastic on the controller is very thin and gouges easily. Youre better off if you just pull up from the side rail and open it like a clam. Guitar pics/pry tools are for clasps, which joycon only have on one side 2: Hand drive all your screws. Again, thin plastic with small screws. Its extremely easy to strip the thread in the shell itself, so its crucial to not over drive your screws and correct threading mistakes quickly. The screws are small, hand fatigue will be minimal. 3: On the right joycon, just make sure it closes up properly. It bows out in the middle if something isnt set right. Yours seem fine but this is just a common enough thing to check for
Very good question. I don’t think I’ve seen people use switch controllers without a switch. You could probably borrow a friends to do it though but I’d assume they write to the switch firmware on the controllers.
Hey bro! i don't know if this is a common problem but.. do you know like how to change ROG Ally's Screen i just want to know is it hard to replace i have a little accident on my screen i just hope can i change my screen i see a replacement on a website called A-Accesories i seen you mods things so many times so maybe i think i could ask you
It’s possible but it’s very much a pain for most people. Motherboard has to come out. The screens are quite expensive. You might be better off finding a used or open box ally and transferring your stuff over to it and selling your old rog ally at a small discount. You’d save alot of money and time
So I've done quite a few analog and shell swaps with joycon and have a few tips. 1: You don't need the guitar pick. The plastic on the controller is very thin and gouges easily. Youre better off if you just pull up from the side rail and open it like a clam. Guitar pics/pry tools are for clasps, which joycon only have on one side
2: Hand drive all your screws. Again, thin plastic with small screws. Its extremely easy to strip the thread in the shell itself, so its crucial to not over drive your screws and correct threading mistakes quickly. The screws are small, hand fatigue will be minimal.
3: On the right joycon, just make sure it closes up properly. It bows out in the middle if something isnt set right. Yours seem fine but this is just a common enough thing to check for
Looking forward to see more posts from you. Sweet creation, CPPC TEK. I pressed the thumbs up symbol on your segment. Persist in the solid work.
Thank you so much ! 💕🤠
Awesome. My wife has this issue with her switch all the time.
thanks man perfect timing i just got my gulikit sticks today and needed a good video!!
🤠🤠🤠heck yeah. I hope you enjoy them and this video makes the process a little easier. Just be patient and it should go pretty smooth.
How do these compare to the gulikit ones?
I'm also curious
If I’m not mistaken they are the same units
I cant even find gulikit tmr for switch lite anywhere
I wonder if these will work on the Quest 2 and quest 3 controllers
If they use the same joystick module in theory yes
How do I calibrate this on PC if I don't have a switch? And would the calibration be written permanently to the controller's firmware?
Very good question. I don’t think I’ve seen people use switch controllers without a switch. You could probably borrow a friends to do it though but I’d assume they write to the switch firmware on the controllers.
How have these been holding up?
Amazing. Haven’t had any issues at all.
@@cppctek Awesome! Do you use your joycons often?
Hey bro! i don't know if this is a common problem but.. do you know like how to change ROG Ally's Screen i just want to know is it hard to replace i have a little accident on my screen i just hope can i change my screen i see a replacement on a website called A-Accesories i seen you mods things so many times so maybe i think i could ask you
It’s possible but it’s very much a pain for most people. Motherboard has to come out. The screens are quite expensive. You might be better off finding a used or open box ally and transferring your stuff over to it and selling your old rog ally at a small discount. You’d save alot of money and time
@@cppctek Ah it's a pain well i have to search on facebook marketplace now. Thank you bro
Does these fit in the pro controllers?
I don’t think so
whats your opinion of these vs gulli sticks aknes.
Probably the exact same sticks to be honest if I had to guess.
🎉awesome my guy got a few u need to do fo me 😂
lol why you always want me to do the hardest jobs lol 😂 all them dang tiny screws and ribbon cables are for the birds lol 😂
@@cppctek big facts but u my guy 😂🙅🏿♂️❤️