If you're interested in any of the tools or equipment I use and you want to help support the channel then don't forget to check out some of the affiliate links in the video description. Thank you for the support!
I've been going through youtubers trying to see someone who can do this well and not get caught up in burning the thing for 10 hours or putting a buttload of extra steps into it, and you definitely have the best cast.
Man, that stuff is expensive. Seems worth it's though, as I bet it goes a long way with how little actually gets used as compared to other investment casting methods. Have you considered using polycast filament?
@@faultyinterface I wonder if one could achieve similar results with clay slip. You'd probably have to be careful with firing temperatures and things like that, but it seems worth a try.
That's a truly amazing cast! I love how you simulated the oxidation of the copper with blue spray paint! If you use ammonia fumes and salt I think you can also get some really cool patterns. How do you avoid voids as I don't see any exhaust tubes?
Thank you! I'll keep salt and ammonia in mind. There are some small voids on the right side of the neck and under the chin. I will cast it differently next time, but the vents from the chin to the top of the sprue worked fairly well.
that was very well done. A few links on some of the materials would be useful as well, or a list in the description. Excellent video - thank you for sharing.
This statue is worth like 200 dollars. Very nicely done. All you gotta know is 3d modeling in blender and casting methods. Ie sand casting and lost casting with ceramic slurry and sand. This video is gold bro.
Nice work. Just a couple of suggestions though: to reduce the amount of bronze used, fill the inner cavity of pla prototype with sand/sodium silicate mix (as you did previously doing aluminum castings) and let it harden by blowing CO2 gas through it. To hold the core in place, pierce PLA prototype and sand core with stainless steel wire. If PLA is not thick enough (about 5-6mm), add some wall thickness using molten wax and then fill the cavity with sand/Na2SiO3
This was really awesome! A lot of RUclips videos tend to cast basically the same thing (Variations of knives and swords and pop culture things) and it was really cool to see something like this! I'd love to see more casts like this one.
Really cool, thank you! Thanks for the alloy! I forgot new pewter is lead free! I was impressed at how the painting/distressing added interest. Much appreciated!
You should put an aluminium foil hat over the ceramic shell before you fill with sand as there would be less chance of you damaging the shell. Also when you’re running your burn out cycle for the PLA you should put a piece of flat bar under the lid to let the gases escape otherwise you’re gonna get carbon build up on the coils and that will shorten their lifespan. Great casting and an excellent choice of colours, what where the colours that you used?
Turned out great! I had my doubts on the spray painting but it really worked out awesome. I would suggest spray painting the plastic 3d printed model with some primer and then some paint before dipping. This would get rid of some of the lines visible frome the layering of the 3d printer. Great job looking forward to more of these vids
This is pretty much the process we used at the foundry I did some design work for. In the future, hollowing out the model would help. You'd have to do it in ZBrush or another program, but it can cut down the weight. I've printed entire monuments for this kind of a process. There are some hot and cold patina solutions from a company called Sculpt Nouveau that you might find fun to experiment with on future efforts, too. I'll link their channel. It's good info. ruclips.net/channel/UCUqAwBoqtvVd6HX2Gzpmbgw
Hi Seth, firstly let me thankyou for such a fantastic set if films. Great research and development, you have very much inspired me and I am sure many people like me that want to cast metal. I have found your films both educational and informative and you have very much aided my home casting project. You ask at the end of your great films for viewers suggestions. It is in this manner I am wondering if you were going to ceramic shell cast some form of iron? I am hoping to do this at some point and would like very much to see how you would go abut this?
Don't know how I missed this video.... Been viewing metal casting techniques and this one, with this example, is very convincing. Well done Sir, you've just added another subscriber. And thank you.
Amazing work, you really master the subject. And it is why I can’t help but to think that using paint lacks nobility. Your using such technic and dedication in what you do that the paint looks like a cheap shortcut. Don’t get me wrong I think what you do is amazing. Try acids or peroxyde !
Great work laddie! For the next time, try to make a shell casting- a hollow one. That way you'd need 1-2 pounds of bronze for the same casting. Less fuel consumed and less time :))
Nice job. The only suggestion of something you might like to try is instead of paint try using a patina like liver of sulphur, this works well on electro formed copper jewellery so it would be worth the experiment. There’s also some other patina solutions that use ammonia and salt from memory, if you’re interested I can try and find it in one of my plating books
How long does that bucket of plaster or ceramic last? Seems like a lot of ceramic for two jobs, unless it lasts a while and you actually used it for more. That’s an incredible casting, great job!!!
Thank you! The material is called Suspendaslurry sold by R&R and it has a shelf life of one year. However I think that it will last significantly longer. That bucket cost $170.
I feel your pain concerning the burns. I wonder , did you spray the piece with a clearcoat? You may already know that you can turn bronze green with chemicals. That too will require polishing the high points now and then, though. Perhaps it's just being pedantic (or maybe more authentic) to allow the piece to corrode some to get that color, but to each his own I suppose.
Wow. Impressive. Would love to be able to have a kiln and a means to melt bronze. Probably take me three years to afford that. Thanks for posting. I assume there is a way to make an inner shell so you don’t have to make a truly solid statue.
How beautiful melt! It looks like the surface of the cold cast is very smooth, is it? Is it due to the lost pla method especially? I've tried brass and greensand but the cast piece is always rough also because it shrinks a lot while cooling down. It looks like your cast hasn't shrank a bit, is there a special reason? Thanks for the video!
What was the ceramic stuff u where dipping in ? I’m in the middle of doing my first lost pla cast and used plaster and sand in the same method as you but that liquid ceramic stuff looks awesome
Nice work! I'm planning to do some lost PLa casting. I was wondering more about the burn out and if you have tried the esun esmooth? This product is meant to be easier to burn out.
yeah, hot stuff plus shorts, the only time this is acceptable is at a barbeque, im glad you learnt this one, next up is the hot splashy plastic and eyeball lesson, you will love that one.
So what is the differance between Pewter & tin? (without too much technicality) if you know incidently great work, I'm hearing more & more about "lost PLA casting".
Thanks for another great video! Quick questions, what kind of sand did you use and what was the temp you heated the part to melt the PLA out? Thanks again.
3D Bronze Glad you liked the video! I used very fine sand from the hardware store but you will probably have better results buying the sand firm R&R. I honestly don’t know exactly what temperature the kiln was at. I just turned it on and left it for a few hours.
You can get very high detail using different sand casting methods the biggest advantage in my opinion is you can cast any shape. undercuts are no issue.
Great video friend .. I congratulate you ...!!!!! What is the investment you use? How do you prepare it? And the sand that you apply to the piece when you remove it from the coating, what characteristics does it have?
This looks super cool! Have you figured out a way to deal with the print layer lines? Would it be possible to use a filament that could be smoothed out using acetone or something like that to get rid of the layer lines before covering it with the ceramic?
Thank you! Some models can be coated in wax if they’re not too detailed. Honestly, I really don’t mind the lines. It’s just part of the process. If you check out the video i made showing how I made the orangutan skull you can see how the wax worked.
Wow, thanks for the awesome video! The casting looks great! I was wondering though, how did you cast it so large and thick without striation or shrinkage?
If you're interested in any of the tools or equipment I use and you want to help support the channel then don't forget to check out some of the affiliate links in the video description. Thank you for the support!
This is hands down the best lost pla method I've ever seen
A couple of gemstones in the eyes would rock
Yes!
I did this on a similar one!! Good suggestion! Check out the video.
@@robinson-foundry looks great
yes, those would be rocks!
where can buy gemstones from?
I've been going through youtubers trying to see someone who can do this well and not get caught up in burning the thing for 10 hours or putting a buttload of extra steps into it, and you definitely have the best cast.
There is one thing that you can count on people doing reliably and that's making shit faaaarrrr more complicated than it should be.
The yellow ceramic material is called Suspendaslurry.
Man, that stuff is expensive. Seems worth it's though, as I bet it goes a long way with how little actually gets used as compared to other investment casting methods. Have you considered using polycast filament?
@@faultyinterface I wonder if one could achieve similar results with clay slip. You'd probably have to be careful with firing temperatures and things like that, but it seems worth a try.
Is there a different brand for suspendaslurr? Super expensive to bring it to Canada
suspendedslurry was my nickname in high-school... JK
I really like the color you chose for the paint, it turned out looking like Patina and really gave the cast this Ancient artifact sorta feeling
Thank you!
That's a truly amazing cast! I love how you simulated the oxidation of the copper with blue spray paint! If you use ammonia fumes and salt I think you can also get some really cool patterns. How do you avoid voids as I don't see any exhaust tubes?
Thank you! I'll keep salt and ammonia in mind. There are some small voids on the right side of the neck and under the chin. I will cast it differently next time, but the vents from the chin to the top of the sprue worked fairly well.
that was very well done. A few links on some of the materials would be useful as well, or a list in the description.
Excellent video - thank you for sharing.
This statue is worth like 200 dollars. Very nicely done. All you gotta know is 3d modeling in blender and casting methods. Ie sand casting and lost casting with ceramic slurry and sand. This video is gold bro.
I can see why you like this artist's work so much. It's beautiful and intricate. Definitely a fun challenge to cast well, which you did!
Nice work. Just a couple of suggestions though: to reduce the amount of bronze used, fill the inner cavity of pla prototype with sand/sodium silicate mix (as you did previously doing aluminum castings) and let it harden by blowing CO2 gas through it. To hold the core in place, pierce PLA prototype and sand core with stainless steel wire. If PLA is not thick enough (about 5-6mm), add some wall thickness using molten wax and then fill the cavity with sand/Na2SiO3
Thank you for using the file correctly, it drive me nuts when people don’t know how to use it, awesome work
In the words of my hero... "This belongs in a museum!"
Well done. Tremendous work and I enjoyed the video immensely.
This was really awesome! A lot of RUclips videos tend to cast basically the same thing (Variations of knives and swords and pop culture things) and it was really cool to see something like this! I'd love to see more casts like this one.
As a jeweler that vacuum casts silver and gold, awesome cast! Great method, excellent transfer of detail from the print!
Really cool, thank you! Thanks for the alloy! I forgot new pewter is lead free!
I was impressed at how the painting/distressing added interest. Much appreciated!
Great job hands down one of the best castings I've seen in a long time.
thanks for sharing your process! absolutelly amazing!
You should put an aluminium foil hat over the ceramic shell before you fill with sand as there would be less chance of you damaging the shell.
Also when you’re running your burn out cycle for the PLA you should put a piece of flat bar under the lid to let the gases escape otherwise you’re gonna get carbon build up on the coils and that will shorten their lifespan.
Great casting and an excellent choice of colours, what where the colours that you used?
Beautiful casting! It’s interesting how the pla only catches fire when you open the kiln and let some air in. Great job though I can’t wait for more.
Turned out great! I had my doubts on the spray painting but it really worked out awesome.
I would suggest spray painting the plastic 3d printed model with some primer and then some paint before dipping. This would get rid of some of the lines visible frome the layering of the 3d printer.
Great job looking forward to more of these vids
This is pretty much the process we used at the foundry I did some design work for. In the future, hollowing out the model would help. You'd have to do it in ZBrush or another program, but it can cut down the weight. I've printed entire monuments for this kind of a process. There are some hot and cold patina solutions from a company called Sculpt Nouveau that you might find fun to experiment with on future efforts, too. I'll link their channel. It's good info.
ruclips.net/channel/UCUqAwBoqtvVd6HX2Gzpmbgw
Well dang that is some awesome work!!!, cant wait to get me a 3D printer for casting projects 👍
Ralph Mourik Thank you sir! I recommend a Creality Ender 3 Pro. They’re great little printers.
Hi Seth, firstly let me thankyou for such a fantastic set if films. Great research and development, you have very much inspired me and I am sure many people like me that want to cast metal. I have found your films both educational and informative and you have very much aided my home casting project. You ask at the end of your great films for viewers suggestions. It is in this manner I am wondering if you were going to ceramic shell cast some form of iron? I am hoping to do this at some point and would like very much to see how you would go abut this?
Don't know how I missed this video....
Been viewing metal casting techniques and this one, with this example, is very convincing.
Well done Sir, you've just added another subscriber.
And thank you.
Amazing work, you really master the subject. And it is why I can’t help but to think that using paint lacks nobility. Your using such technic and dedication in what you do that the paint looks like a cheap shortcut. Don’t get me wrong I think what you do is amazing. Try acids or peroxyde !
Great work laddie! For the next time, try to make a shell casting- a hollow one. That way you'd need 1-2 pounds of bronze for the same casting. Less fuel consumed and less time :))
Amazing - really cool project.
Thank you!
Nice job. The only suggestion of something you might like to try is instead of paint try using a patina like liver of sulphur, this works well on electro formed copper jewellery so it would be worth the experiment.
There’s also some other patina solutions that use ammonia and salt from memory, if you’re interested I can try and find it in one of my plating books
Lost PLA Casting is very similar to the traditional Lost Wax Casting method. Great job!
Neat work and video... 😎👌🏽 Congrats from Mexico 🇲🇽
Wow! Beautiful!
Thanks!
¡Hermosísima! Gorgeous! Congrats!
i like when i see people burn plastic :) i love all plastic things....good job
That's a lesson learned the hard way, be glad that wasn't molten metal. Great cast.
Nice touch with the paint 👌😌
How long does that bucket of plaster or ceramic last? Seems like a lot of ceramic for two jobs, unless it lasts a while and you actually used it for more. That’s an incredible casting, great job!!!
Thank you! The material is called Suspendaslurry sold by R&R and it has a shelf life of one year. However I think that it will last significantly longer. That bucket cost $170.
It's awesome. Fantastic work
Truly Amazing artwork! 1st video & I know I'm subscribing straight away!
Beautiful.. you can still see the print lines in it...
Your video style reminds me of Brian Oltrogge. Calm and relaxing but also well planned and intelligent.
This is awesome.
Great job on the casting and the video. Sucks about the burns, glad it wasn't worse. Burning plastic is nasty to skin.
Dustin Skye Thank you! My leg healed well but did scar. Live and learn.
That's fucking sick. Love the cyan paint and rubbed off technique
Fantastic Artwork
Dude, that thing is rad! You definitely deserve waaaaay more subs
i fn love it good job and process. i cant wait to learn from you.
Beautiful n inspiring! Loved evey bit of detail. Especially how you gave the base an edgy look. 🤩
That's awesome. It would be right at home in one of those Tool music videos...
Wow!!!!!!!!!!!!!!!!!!!!! amazing, you got me super interested in knowing more about casting stuffing.
Fantastic! When I saw the title, I thought you can pour over the PLA itself and that is how it is lost :)
I admire your work.. amazing.. nice job..
Очень красиво получилось
awesome casting and very informative
Beautiful end result.
The details look great!
Hey, Dude. I'm new here. Your work is awesome! The statue stayed very nice. Congratulations!👍🇧🇷
David Dias de Souza Filho Thank you!
Hola Seth: muy bonito trabajo!!
Why you not try use some aluminum bronze? Like 95% copper 5% aluminum. Cheers
Great showy even the failures.
Of course you can send me the statue. Lol. Came out Fantastic
I would sure love to have one of my sculpts cast in bronze! Great work!
I feel your pain concerning the burns. I wonder , did you spray the piece with a clearcoat? You may already know that you can turn bronze green with chemicals. That too will require polishing the high points now and then, though. Perhaps it's just being pedantic (or maybe more authentic) to allow the piece to corrode some to get that color, but to each his own I suppose.
Wow. Impressive. Would love to be able to have a kiln and a means to melt bronze. Probably take me three years to afford that. Thanks for posting. I assume there is a way to make an inner shell so you don’t have to make a truly solid statue.
You make very beautiful works of art. Try casting something nice with the alloy Nordic gold. 😊
Dude that is awesome!
Turned out great!
How beautiful melt!
It looks like the surface of the cold cast is very smooth, is it? Is it due to the lost pla method especially? I've tried brass and greensand but the cast piece is always rough also because it shrinks a lot while cooling down. It looks like your cast hasn't shrank a bit, is there a special reason?
Thanks for the video!
great cast. would have tried to build a natural patina from copper nitrate though, instead of painting.
What was the ceramic stuff u where dipping in ? I’m in the middle of doing my first lost pla cast and used plaster and sand in the same method as you but that liquid ceramic stuff looks awesome
Suspedaslurry
@@eternal7083 SuspendaSlurry® .?
@@arturoarturo8452 yes, SuspendaSlurry
made a typo
Thanks so much just into 3D printing. Wife’s a jeweler .
So you know where this is going .
Thanks
Nice work! I'm planning to do some lost PLa casting. I was wondering more about the burn out and if you have tried the esun esmooth? This product is meant to be easier to burn out.
great video, really perfect finished product, I was wondering how long did it take to burnout and at what temperature?
Great result! Isnt the melting of the plastic toxic? Can imagine it will smell alot.
yeah, hot stuff plus shorts, the only time this is acceptable is at a barbeque, im glad you learnt this one, next up is the hot splashy plastic and eyeball lesson, you will love that one.
You are wearing some decent Sydney safety shorts there... ;)
yup learned the hard way )
It's wonderful work!
So what is the differance between Pewter & tin? (without too much technicality) if you know
incidently great work, I'm hearing more & more about "lost PLA casting".
Love the videos you should some more of these suspendaslurry castings they come out so good. Just do it! Lol
Thanks for another great video! Quick questions, what kind of sand did you use and what was the temp you heated the part to melt the PLA out? Thanks again.
3D Bronze Glad you liked the video! I used very fine sand from the hardware store but you will probably have better results buying the sand firm R&R. I honestly don’t know exactly what temperature the kiln was at. I just turned it on and left it for a few hours.
Beautiful work!!!
Nicely done! The vents made for a cool beard, shoulda left ‘em 😂😆
I was thinking the same and actually said NOOOOO when he was cutting them 😋😂👍
awesome my friend.. goodjob😀😀😀
This seems like a long process compared to the plaster and greensand method, what are the advantages with this method (i'm still learning) ?
Gary McKinnon Yes, it is a long process. The trade off is high detail and the ability to cast complex objects that would be impossible to sand cast.
You can get very high detail using different sand casting methods the biggest advantage in my opinion is you can cast any shape. undercuts are no issue.
Thanks both.
Super! A perfect job!
This is pretty amazing work.
Amazing work!! Thanks for sharing.
Very cool..i will teach myself to do this one day :)
Sorry to see you got burned, but this is why we wear ppe.
Great work and good video
Great video friend .. I congratulate you ...!!!!!
What is the investment you use? How do you prepare it? And the sand that you apply to the piece when you remove it from the coating, what characteristics does it have?
You should try a forced patina on your bronze work!
Awesome thanks for sharing
Nice work man!!!!
Thank you!
That turned out really good. I really want to try the suspendaslurry, but, with the shipping and the cost of it, its really close to double the price.
That was a very good vídeo content thankyou
kitchen utensils represent
Awesome job!
Excellent video!!
I would like to know what is the yellow liquid that you use in the mold
This looks super cool! Have you figured out a way to deal with the print layer lines? Would it be possible to use a filament that could be smoothed out using acetone or something like that to get rid of the layer lines before covering it with the ceramic?
Thank you! Some models can be coated in wax if they’re not too detailed. Honestly, I really don’t mind the lines. It’s just part of the process. If you check out the video i made showing how I made the orangutan skull you can see how the wax worked.
Good job.
Wow, thanks for the awesome video! The casting looks great! I was wondering though, how did you cast it so large and thick without striation or shrinkage?
Beautiful work