A 4.7k ohm 2w resistor can be used on the plug, in position 2&3, if the swirl motor should fail. Love your content, very helpful as I have a Chrysler 300c with the om642 👍
Not here , sprinters om642 checking when swilr flap is open or closed ,when will still open for example by resistor mod , then will go to limp mode , resistor work good with om642 below 2009 w211 cls jeep, not for up 2009-2010
@@amimenamimen8599 I have a 2007 MB GL320 with P2513 Code I believe its the Swirl Valve. Could I use the 4.7k ohm 2w resistor in position 2&3 to bypass the valve?
Are swirl flaps optional for this engine? I removed ones for my diesel bmw. I read they get brittle and break off in the intake. PS: I'm coming from Toyota channel and it's really odd to not hear "welcome to Toyota maintenance RUclips channel" lol. Keep up the great work.
dear friends and dear friends! I have watched this tutorial several times, I am in the same situation, for a Vito WDF 639..V6..3L. I received the new model so I could replace it. But, so here it is!, where can we find these famous Clips that you show in this tutorial?. For my part, I looked everywhere, I couldn't find his clips. If someone can tell me what the reference would be or on which site we can find them, so that I can start the replacement, cordially, YOURS from Gerard Monterin.
REMOVE THE INTAKE MANIFOLD, clen it and I bet the swirl flaps are not working properly, yes yes from a top it might seems that they are OK but I bet they are more KO then OK.
Thank you a lot! Very clear explanation. Greetings from Patagonia, Argentina.🙌
Great video!! Thank you and to people like you who give us a clue about all this small things who cause a big headeck😁👍
the t30 spring arm. when installing new is it supposed to be tightened? or is it supposed to be able to be compressed?
A 4.7k ohm 2w resistor can be used on the plug, in position 2&3, if the swirl motor should fail.
Love your content, very helpful as I have a Chrysler 300c with the om642 👍
Not here , sprinters om642 checking when swilr flap is open or closed ,when will still open for example by resistor mod , then will go to limp mode , resistor work good with om642 below 2009 w211 cls jeep, not for up 2009-2010
@@amimenamimen8599 I have a 2007 MB GL320 with P2513 Code I believe its the Swirl Valve. Could I use the 4.7k ohm 2w resistor in position 2&3 to bypass the valve?
@@bfams11you can will be work
@@amimenamimen8599 do I just pull the connector and jump it? That seems easy enough.
Can also be smart to change the gasket for the oil cooler under there. The orange silicone seals starts to leak.
Thank you so much for the info 🎉
I tried cleaning it with break cleaner but electrical pins keep getting oil in them.is this motor gone bad it's full of oil.
Are swirl flaps optional for this engine? I removed ones for my diesel bmw. I read they get brittle and break off in the intake. PS: I'm coming from Toyota channel and it's really odd to not hear "welcome to Toyota maintenance RUclips channel" lol. Keep up the great work.
do the flaps work the same on both sides,open open close close right?
dear friends and dear friends! I have watched this tutorial several times, I am in the same situation, for a Vito WDF 639..V6..3L. I received the new model so I could replace it. But, so here it is!, where can we find these famous Clips that you show in this tutorial?. For my part, I looked everywhere, I couldn't find his clips. If someone can tell me what the reference would be or on which site we can find them, so that I can start the replacement, cordially, YOURS from Gerard Monterin.
Thank you for this video. It is very good.
very good explination .aprecciate the help.
What caused the turbo to go bad?
Can a 100k resistor in the plug shunt these off similar to my gl320?
Dobra prace. Dik
Great information 👍
Mines been totally removed and coded out of the ecm.
REMOVE THE INTAKE MANIFOLD, clen it and I bet the swirl flaps are not working properly, yes yes from a top it might seems that they are OK but I bet they are more KO then OK.