Thanks Ron. My dad is a retired body and fender man, who brought all his tools home. Having access to the various graters, files, putty knives, etc., I just needed some bondo (picked up a gallon at Home Depot), and some basic techniques, which your clip fully covers. I appreciate it.
Finally somebody who does a great explanation plus some cool tricks. I’ve worked with residence for years but never use Bondo. Getting the mix ratio is right is where I was concerned and you gave me a good point to work with. Thanks again for some decent explanations.
A little time saving trick I learned in a cabinet shop is to wait until the bondo is almost set up so it's not sticky but still a bit pliable and you can cut any excess smoothly off the top of the repair with a putty knife.
Thanks for your video. I can add that acetone works great for final cleaning of the tools. Also when mixing little amounts of the putty like few grams (and I do it quite often), an electronic scale with 0,01g resolution is a great help in dosing the right amount of the hardener.
What is the ratio amounts for these two products ? I’m doing wood filler on a table and I only want a small amount but can’t seem to find any real number amounts for this mix . Thanks . I hope you can understand my question! 💁🏼♀️
Great video. I'll admit that I was using bondo all wrong for 20 years. (In my defense, I've used it very rarely, but probably because it was such a pain because I was doing it all wrong.)
Thank you loads! I'm not trying for a smooth finish, but your blending technique is the best I've found. Good advice! (I understand acetone will attack dried leavings, and someone said mineral oil -- read 'baby oil' -- will also clean tools and mixing surfaces, though I haven't tried it yet. I know it cleans brushes better than turpentine and is less toxic ...)
I wish someone would explain the ratio of hardener to filler in more exact terms. He says the ratio is critical but then just eyeballs how much hardener he adds. This is not very helpful to a new and/or infrequent user. I may use Bondo a couple of times in my lifetime and I don't want it hardening before I'm done with my project, or taking a week to harden because I added too much. How about something like "X ounces/grams of hardener to Y ounces/grams of filler gives you 15 minutes before it hardens".
Check out ChrisFix's video on rust repair. He has a neat trick on how much hardener to use. Its the video where he's repairing a blue mazda quater panel
It doesn't get rock hard, like fiberglass resin. You can nail through it, as long as you are nailing all the way through to the substrate. Body fill alone will not have much holding power. I was taught that filler should not be applied more than a 1/4 inch thick. I don't think I remember ever nailing through it: however, I think it would behave somewhat like MDF . . . Drill first. For more information Wiki Bondo.
Ron Budman, thank you for this very helpful information. I am in the process of refinishing a cast iron jockey made in Canton, Ohio by the Champion Fence Co. ? years ago. I have filled in several spots with BONDO tho I had an earlier problem with my mixture drying out sooner than I could work with it. I learned to mix smaller quantities and that helped. Is there any chance of thinning a mixture? The BONDO residue is chalky when sanded, suppose that's normal. I think it is ready to prime, using MOBILE Primer and Farm Implement Paint. Having learned a LOT, and having a wonderful time. Wish you were here! Elizabeth (age 80) .
You said that it doesn't harden in the can but I have some filler thats several years old and has never been used but it's the thickness of clay or silly putty. Its not runny at all, but completely moldable. Is that going to matter if I use it?
Can you put filler over dtm high build?So many debates over this. Just got off the phone with Tamco they said no filler on bare metal creates heat then condensation on metal and to put over there DTM high build 5310. I do not need epoxy if car is inside all the time it will save you a lot of money just block and top coat your done and still have epoxy properties in the DTM.
+Adam Baber If you apply the Bondo too thick it will either end up cracking or even just falling off. If you can pound the dent out enough that only a very thin coat of Bondo is required, yeah, it can save you having to replace the panel.
What's the proper mix ratio? I've noticed everybody's "about this much" ratio is different. I'd rather do it right the first time and not have to redo it.
I was taught many years ago to add about one inch of hardener to a golf ball size amount of Bondo. However, it is always best to go with a little less than too much.
not going to last more than a couple seasons outside at least in the Ne areas. you need to use the bondo multi purpose filler on wood but all the mixing and applications the same
There is actually a comment below somewhere from a guy that says mixing on cardboard is perfectly OK. I've actually been mixing plastic since it was first introduced to the industry back in the 50. I remember my father saying, "that will never work." Even into the 70's we were still using lead on sail panel seams.
Thanks Ron. My dad is a retired body and fender man, who brought all his tools home. Having access to the various graters, files, putty knives, etc., I just needed some bondo (picked up a gallon at Home Depot), and some basic techniques, which your clip fully covers. I appreciate it.
Lucky man
Finally somebody who does a great explanation plus some cool tricks. I’ve worked with residence for years but never use Bondo. Getting the mix ratio is right is where I was concerned and you gave me a good point to work with. Thanks again for some decent explanations.
A little time saving trick I learned in a cabinet shop is to wait until the bondo is almost set up so it's not sticky but still a bit pliable and you can cut any excess smoothly off the top of the repair with a putty knife.
After watching this, my first bondo attempt was successful! Thank you Ron
You're a very good presenter. I found many of the little tips throughout quite helpful.
Thanks for your video. I can add that acetone works great for final cleaning of the tools. Also when mixing little amounts of the putty like few grams (and I do it quite often), an electronic scale with 0,01g resolution is a great help in dosing the right amount of the hardener.
What is the ratio amounts for these two products ? I’m doing wood filler on a table and I only want a small amount but can’t seem to find any real number amounts for this mix . Thanks . I hope you can understand my question! 💁🏼♀️
Thank you for your time and knowledge was very helpful and I feel like I can use bondo now because of you God-bless
You are so welcome
Great job , I feel you showed a great demonstration!
Thank you!
Great video. I'll admit that I was using bondo all wrong for 20 years. (In my defense, I've used it very rarely, but probably because it was such a pain because I was doing it all wrong.)
I appreciate the pro tips Mr. Budman
Thanks Ron ! I'll give 'er a go tomorrow !
Great "voice of knowledge" energy.
Right on buddy thanks for the help. Your wisdom is bondless!!
Thank you, this was really helpful and gave me the confidence to do it! Wish I had all those tools though, I don't have any!
I am going to fix my metal roof porch using bondo. This is good idea for repairs
Thanks, Ron! I appreciate the help!
Glad to help!
this is like the bestest coolest video ever
Thanks so much!
Thank you loads! I'm not trying for a smooth finish, but your blending technique is the best I've found. Good advice! (I understand acetone will attack dried leavings, and someone said mineral oil -- read 'baby oil' -- will also clean tools and mixing surfaces, though I haven't tried it yet. I know it cleans brushes better than turpentine and is less toxic ...)
William R Warren Jr Hi WRW Jr, this is good info, too. Thanks. E.
Awesome video! Helpful and informative even for a guy who considers himself well experienced! Look forward to more!
BONDO make their own "color keyed" to the RIGHT mixing color.
Where can I find this? I Googled it, but found nothing.
Bondo is a brand name and is sold everywhere. All shops and Walmart.
This is great Ron. I have an old table to resurface and paint, and your video was a big help.
Excellent video! Thanks for your help!
Thanks Sir Ron, i will apply your tutorial...
Great explainer videos. Thank you!
absolutely fantastic howto. thank you so much!!!!!
Awesome coverage of the basics. Where did you get the half round rasp? Didn't see many with the holes.
Thanks for sharing your knowledge and wisdom; you're awesome!! 😎
Wow great video!
I wish someone would explain the ratio of hardener to filler in more exact terms. He says the ratio is critical but then just eyeballs how much hardener he adds. This is not very helpful to a new and/or infrequent user. I may use Bondo a couple of times in my lifetime and I don't want it hardening before I'm done with my project, or taking a week to harden because I added too much. How about something like "X ounces/grams of hardener to Y ounces/grams of filler gives you 15 minutes before it hardens".
10% is good.
Check out ChrisFix's video on rust repair. He has a neat trick on how much hardener to use. Its the video where he's repairing a blue mazda quater panel
In case you have not found this in the last two years....
ruclips.net/video/KN_pWQXElNI/видео.html
Read the instructions
@@michael7144 I did, and, using a cubic inch as a metric is not helpful.
that was an informative and entertaining video. The music was good as well :) Good Job!!
Thank you for the tutorial
Great video
It doesn't get rock hard, like fiberglass resin. You can nail through it, as long as you are nailing all the way through to the substrate. Body fill alone will not have much holding power. I was taught that filler should not be applied more than a 1/4 inch thick. I don't think I remember ever nailing through it: however, I think it would behave somewhat like MDF . . . Drill first. For more information Wiki Bondo.
Ron Budman, thank you for this very helpful information. I am in the process of refinishing a cast iron jockey made in Canton, Ohio by the Champion Fence Co. ? years ago. I have filled in several spots with BONDO tho I had an earlier problem with my mixture drying out sooner than I could work with it. I learned to mix smaller quantities and that helped. Is there any chance of thinning a mixture? The BONDO residue is chalky when sanded, suppose that's normal. I think it is ready to prime, using MOBILE Primer and Farm Implement Paint. Having learned a LOT, and having a wonderful time. Wish you were here! Elizabeth (age 80) .
Thank you. My first mix was wasted. Coz I put some amount of hardener.
Thanks grandpa!
Thank you very much , Helped me alot to understand .. You rock dude ..
Great video. 🙂👍
Very informative. Thank you!
You said that it doesn't harden in the can but I have some filler thats several years old and has never been used but it's the thickness of clay or silly putty. Its not runny at all, but completely moldable. Is that going to matter if I use it?
Thank you for this video sir
merci beaucoup pour le programme
would this work to fix a crack in a camper bathtub? If not what would you use?
awesome tips thanks sir
Great vid
Great info but I’ve failed at this kind twice, think I’ll stick to DAP for right now.
It drys to fast on me.
good vid, i like your style ;)
Very helpful. Thanks a lot
thanks toolman
What brand/where did you buy the curved rasp file? I haven't been able to find anything exactly like that one.
Went to the website listed and it’s not there. Website might be down?
thanks my man , i used to put a lot of hardener
For everybody all of the stuff he is using can be found at your local hardware store
Thanks for sharing.
Good vid! Thanks man
Can you put filler over dtm high build?So many debates over this. Just got off the phone with Tamco they said no filler on bare metal creates heat then condensation on metal and to put over there DTM high build 5310. I do not need epoxy if car is inside all the time it will save you a lot of money just block and top coat your done and still have epoxy properties in the DTM.
where can i buy the curved brass file?
Good video. Over here sounding like channel 12 news though lmao
How hard is the bondo after it is finally cure? Can it be drilled or nail in?
You are amazing
I dented my back right side quarter panel near the tire. Curious if I can use bondo to cover it instead of getting a whole new quarter panel lol
+Adam Baber If you apply the Bondo too thick it will either end up cracking or even just falling off. If you can pound the dent out enough that only a very thin coat of Bondo is required, yeah, it can save you having to replace the panel.
+John Ratko Thanks for replying to Adam's post . . . somehow I missed it.
thank you friend
What solvent do I use to soften the grey unmixed putty? Mine is starting to dry up and now it's closer to the consistency of a wood filler.
Sorry, I really don't have a clue.
Thank you bro
Thanks sir, I am a woman doing this for the first time🙂
How do you OPEN THE CAN?
What's the proper mix ratio? I've noticed everybody's "about this much" ratio is different. I'd rather do it right the first time and not have to redo it.
I was taught many years ago to add about one inch of hardener to a golf ball size amount of Bondo. However, it is always best to go with a little less than too much.
@@RonBudman Perfect timing! I was just starting to mix some. Thank you!
Anyone else notice the crack in the glass that formed when he dropped the tool on it?
Love it! :)
Thanks Ron
Can i also use this on cement?
just use cement
Thank you
Is spot putty stainable sir?
I don't think so.
not going to last more than a couple seasons outside at least in the Ne areas.
you need to use the bondo multi purpose filler on wood but all the mixing and applications the same
What’s the hardener brand, please
Bondo comes with it's own tube of hardener
@@johnathin79 mine was missing.
If anyone knows it, please let me know. Thank you
@@bellabell1188 should've came with it. It's a set.
You're so cool thx.
Good video, thanks!
thanks
im starting to use this on scale 1:24 model cars to fill gaps
Thanks Ron. I cannot find curve something file in HomeDepot. did I get it wrong?
Try Amazon goo.gl/tjvMlP or your local auto body supply store or NAPA.
The only thing I don't like about the product is that the can is not full it's about 3rd full
👍👍👍
Good
thanks for the short concise vid..Any thing over 10 min is way to much BS....thanks again
Actually bondo will dry out
YOU DID NOT EVEN BOTHER SAYING IN WHAT RATIO TO MIX!!! ARE YOU CRAPPING ME??????????????
Learn something from your side
Makes me cringe seeing people in the business using cardboard or plywood to mix bondo.
There is actually a comment below somewhere from a guy that says mixing on cardboard is perfectly OK. I've actually been mixing plastic since it was first introduced to the industry back in the 50. I remember my father saying, "that will never work." Even into the 70's we were still using lead on sail panel seams.
@@RonBudman where you at ?
This video is completely vague about how much hardener to use per unit of filler. Useless.
Yea cause advice from a stoner fills me with so much conference
Awesome video!
Glad you enjoyed it
Thank you