T.A.L.Y. - - - "Torque Assisted Left Yaw".... The main motor speeds up to assist the helicopter's yaw to the left using the main motor's increasing torque forces on the frame of the model around the vertical axis of its main shaft. You can hear "T.A.L.Y." in action when Jeff manually yaws the helicopter to the right (10m:32s), the main motor's RPM increases to help bring it back to the left. At the same time, the tail rotor's RPM decreases to allow left yaw to occur.... I believe "T.A.L.Y." is only found on helicopters with fixed pitch tail rotors. But I am very new to this stuff. I am not 100% sure on that.
@@westhobbiesrc8051 I think this is a huge limitation for this otherwise great heli. I do not understand why they spent so much with the great design and not support a protocol with telemetry. Even my tiny Nano S3 (several years old already) came with telemetry.
Yes and no, yes I figured out to do it. But it’s a complicated mix setup. I just heard of anther way Im Going to try. But if you have your normal mode with self level you could always go back to normal at any time and the self level will work as a rescue.
@@westhobbiesrc8051 does this rescue prevent the helicopter from going inverted? I guess what I'm asking is it a self level or is it a true rescue mode?
@@LichaelMewis Goosky or OMP does not have a true rescue mode. You are modifying self level to make a rescue, but yes rescue would stop you from going inverted when flipped.
Great video. I noticed when you were moving helicopter around while spooling up the satellite light was blinking instead of on solid does it matter? Also my friend put gear on switch D and it’s like having heading hold. Have you tried that yet? Thanks again great work and video.
Thank you, yes it should be solid. I was using a old DSM2 RX to bind and I rebind with a DSMX RX and the light was solid. Yes, you can put that on any switch. Personally I don’t ever use it but you can have it setup as “rescue” as well.
Hey! I got my S2 today, the cyclic moves in all orientation properly except collective. When I go positive the swash plate goes down, and visa versa. Any idea?
Thanks! Thank you for your reply. While at it, with regards to the attitude reset, the one holding the the full aft cyclic for 10secs, can it be done with the model static on the level ground with blades off? Thanks for your time! George
What is that old RX Model? I have a DX8 and 3 AR636B’s in planes, no Remote Ports. Need to find an older used Receiver. Ok figured out I can get an SRXL2 for $45. Serial Micro Receiver With Bind Button. 😊
I have mind setup on opentx, I have a switch which is effectively throttle hold, it just switches between 100% flat line and 0% same pitch curve in both. balls out 🙂
@@westhobbiesrc8051 there are plenty that have had no issues with spektrum but have seen too many issues myself mostly losing bind and refusing to rebind. Had a play with an nx8 recently, the UI was slow, laggy and loads of "screen rip" the case felt horrible and cheap. Something you could forgive on a £150 radio but not on something twice that price. The ix 12 is a £660 radio. Which is mental in today's world
@@DorsetSaferRoads 99% if people problems with spektrum is they use cheap Chinese receivers which are crap and lose bind or refuse to bind exactly what you were claiming. There is a reason I fly spektrum in my $20,000 plus turbines or 300mph plus speed planes. If you use genuine receivers never have an issue. But everybody is so quick to bash or blame spektrum themselves because they are too cheap to buy an actual receiver and don’t have any idea why it loses bind or fails. I’ve had three gimbal springs brake on the TX16S already. They are just such a cheap crafted radio even the feel of them is cheap they remind remind me of the old Chinese cell phones from years ago. They’re a great radio for somebody that doesn’t have expensive models or doesn’t fly anything big. Definitely a great radio but if you’re flying expensive aircraft or big aircraft you need reliability. Flying spektrum for 15 plus years and have gone over 300mph and never a Single issue. I am more than glad to pay every penny that they charge for the radios and receivers to never have to worry and I have a peace of mind. And on top of that, they have the best customer service in the game. You can drop your radio and break it and send it to them they fix it for free. You can crash an airplane or helicopter and destroy the receiver. You send it to them they fix it no charge to you. No other company out there that’ll do that. Got a remember I’ve been in this hobby a long time I have flung every brand of radios there is. There’s a reason I go back to spektrum every time.
I have watched this vid again,like other vids of yours. i might of mis-understood something,when you said you are working on a rescue mode for Spektrum system will this be for the Goosky s2 OR will it work on the OMP m1 also? thanks
Thanks for always watching! The rescue will work for M1 and M2 as well as the S2! I have already tested on the M2 and M1 and working great so I’m going to be making a video soon!
As of right now there is no video on rescue for spektrum yet! But very soon I have been testing and working on a file! If you set this up the way I did in the video you will have self level in normal mode and that can be used as a “rescue” but I’m building a file that will add positive pitch and upright the heli.
Please keep us up to date on that the android app is working we need a video on a general settings go throw on servos and speed and leveling the swatchplate. Thank you for all you have done.
@@bobwatson6558 Will definitely do! They just released the ISO app! I’m in the process of downloading it and then going to play with it and then make a video!
I have a Goosky S2 and a Blade 360 smart , the Goosky seems to center itself better... Doesn't follow last command so much... The blade doesn't seem to center itself as readily as the goosky , I set up the blade as per the manual, spectrum DX7 gen 2 would you say that sounds normal when comparing the two ,I know they're different flight controllers , just wondering if I can do something to make the blade not follow last command so much... Thank you
Yes it will! I used a DSM2 satellite in mine for a long time. Actually I still think it’s a DMS2 satellite in it now. You will just need to bind with a separate receiver.
Thanks for the quick response. I crashed my trusted T-Rex 250 and there are almost no spare parts to be had. I think it could be a sign to get something more up to date in that size! 😀@@westhobbiesrc8051
Hey Jeff, can you use a Kensun satallite like on the M2 with the Goosky? Also, I shouldn't have any issues running M2 evo batteries with my S2 right? Thanks!
Hey man great video! Just curious, I’m your vid you only use the spektrum satellite for binding and then remove it after that’s done but all the other videos I’ve seen they mount the satellite receiver to the heli and keep it connected. Is there a reason for this? Thanks heaps
Hi! I just got one, thanks for the video! You always help me! My futaba doesn’t have the option function, so my ch5 always going to be gyro. So, how can I do it? I noticed if I change value from avcs to normal it changes the modes, however, if I put gyro as inh, I don’t know if its going to be functional for gains, because it would be always in 3d, thats fine, but the gyro sens would work? Thank you so much. Nobody uses t10j anymore, i need to upgrade.
so I don’t know futaba anymore. been a long time since I’ve even played with one. but you don’t need to control gain. CH5 just needs to see a +100/-100 value to work the Auto level. +100 is on and 0 or -100 is regular mode.
Like all helicopters you’re gonna have your channel 6 standard. And then I’m assuming 7 and 8 would be for rescue. Thank you! I plan on setting it up to the TX16S and making a video very soon.
@@westhobbiesrc8051 Guess you never got around to setting up the Goosky on a TX16S. Just purchased the Goosky and a TX16 running EdgeTX. Would be nice to have seen a setup from you. Was flying helis years ago on Spektrum but haven't done so since 2012. Gave the DX8 to a friend way back then. I have a couple of my flybared Align450's flying with the TX16 and gonna try the Goosky setup in a day or two. Was looking forward to seeing how you setup Rescue etc. Nice vids BTW
@@rydfree Unfortunately no, my TX16S started giving me a bunch of problems and crashed two helicopters so I quit using it. The set up for the S2 is identical to the M2 video. So you can use that. I personally prefer spectrum transmitter‘s over the radio master for multiple reasons but reliability is the biggest one. I’ve had quite a few issues with it that I just fixed and never mentioned but once I crashed a couple helicopters from the radio losing RF and going into failsafe that was enough for me. Thank you.
Wow, only 40 throttle for normal mode? Seems kinda low.. I'm waiting for AMain to get these back in stock, then I'm getting one. (I want a white one to match my lil S-1, and they're out of em.)
Thank you, so personally I don’t use or like JST connectors. I’ve had one to many melt. I would highly recommend leaving the XT30. It’s a far better connector. I’m not sure on Amps.
Hey Jeff! I am interested in getting into a GooSky S2 to start back into helis. I fly with a Futaba 18MZ for my fixed wing stuff. I can't find any good Futaba setup guides. I scanned the QR code for the T16SZ which is close to the 18MZ (same menus etc) but it's mostly Chinese or something. Any ideas where us Futaba folks can get better info on the setup? You would think that a company that their reciever is using a Futaba protocol would have tons of setup info. Thanx for your help and great videos 🤌🤌👍
You have to assign channel 5 which is the gear channel to your flight mode switch or whatever switch you want to be auto level. It needs to see a positive 100 value to be on and a zero or -100 to be off.
hello,will you rescue mode for spektrum be for the lastest high spec tx like yours? will the older DX7/8 be covered? Also for a novice like me actually seeing the settings was very good. would you be able to do a similar vid on duel rates? never quite understand them regards setup
hello! So technically speaking yes it should work on any spektrum radio. It will look different but I can actually even do a set up on a DX7! I have a DX7, DX9 and IX12 so I will be sure to test all three of them and make sure they all work the same. Because I fully understand that everybody has a expensive fancy radio like mine. I flew a DX6 then a DX7 then DX9 for 7 years then went to the IX12. Yes I can make a separate video on understanding Duel rates.
@@garymurphy5133 You’re very welcome! When I started this channel a year and a half ago I wanted to be one of the only channels that replies to every single comment and does my best to help every single person that I can! Because there is way too many people that just post videos but actually don’t do anything for the community or help the people that don’t understand.
@@westhobbiesrc8051 Fantastic attitude and goals for posting your Incredible Videos Jeff! On behalf of all who watch your Videos for the Instructional part of them, Thank you very much!! I also appreciate your Flights because of your Skill Level and Novice Pilots can see what these and other RC Helicopter's are actually capable of! People definitely need to show even the 200 Size Heli's the Respect that they deserve, in 1 second a Novice Pilot can go from Hovering to a serious cut! Take Care, Best to You and your Family and Stay Safe my friend!
Hey guy thx for the video! I just got the ix14 and the goosky s2. Which newer model Satellite’ (?) I think was the word u used? Should I get now to make these two work? I’m assuming the 6 inch extension doesn’t come with it either?
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
The was a HUGE help for my NX8, Jeff. Thanks a lot for making the video.
? at the roughly 10:40 mark of your video, I can’t/don’t understand the term “tally” and its meaning/application.
Please clarify this for me.
Thanks!
Same question, what is tally?
T.A.L.Y. - - - "Torque Assisted Left Yaw".... The main motor speeds up to assist the helicopter's yaw to the left using the main motor's increasing torque forces on the frame of the model around the vertical axis of its main shaft. You can hear "T.A.L.Y." in action when Jeff manually yaws the helicopter to the right (10m:32s), the main motor's RPM increases to help bring it back to the left. At the same time, the tail rotor's RPM decreases to allow left yaw to occur.... I believe "T.A.L.Y." is only found on helicopters with fixed pitch tail rotors. But I am very new to this stuff. I am not 100% sure on that.
Thanks
@@mikec9404 Thank you! I greatly appreciate it!
With this setting do you get any battery telemetry from the Goosky to your Spektrum Radio? Thanks
Unfortunately no, there is no battery telemetry with spektrum because the Goosky FBL does not support SRXL2
@@westhobbiesrc8051 I think this is a huge limitation for this otherwise great heli. I do not understand why they spent so much with the great design and not support a protocol with telemetry. Even my tiny Nano S3 (several years old already) came with telemetry.
Jeff any word on how to setup the rescue for the S1 and S2 with Spektrum?
Yes and no, yes I figured out to do it. But it’s a complicated mix setup. I just heard of anther way Im Going to try. But if you have your normal mode with self level you could always go back to normal at any time and the self level will work as a rescue.
@@westhobbiesrc8051 does this rescue prevent the helicopter from going inverted? I guess what I'm asking is it a self level or is it a true rescue mode?
@@LichaelMewis Goosky or OMP does not have a true rescue mode. You are modifying self level to make a rescue, but yes rescue would stop you from going inverted when flipped.
Super video, super helicopter
Thank you!
Great video. I noticed when you were moving helicopter around while spooling up the satellite light was blinking instead of on solid does it matter? Also my friend put gear on switch D and it’s like having heading hold. Have you tried that yet? Thanks again great work and video.
Thank you, yes it should be solid. I was using a old DSM2 RX to bind and I rebind with a DSMX RX and the light was solid. Yes, you can put that on any switch. Personally I don’t ever use it but you can have it setup as “rescue” as well.
Ah ok thanks for the reply back. I just got the ix14 so setup is the same right?
@@hobie278 yes sir! Everything is the same. I fly on a IX14 now as well.
Good content as always
Thank you! Appreciate it!
Hey! I got my S2 today, the cyclic moves in all orientation properly except collective. When I go positive the swash plate goes down, and visa versa. Any idea?
Did you ever sort out a decent rescue option on this combo?
@@FletchyDog I did but it’s not simple, it takes a bit of mixing to make it work.
@@westhobbiesrc8051 I would love to see a video walk through on that. I just got one of these, running it with a Spektrum DX6 gen2.
Hi, any progress on the rescue file? Many thanks!
So it works great on the M2 but not the S2 (I know weird) so I need to play more. I think it’s in the FBL and trying to figure out a way around it.
Thanks! Thank you for your reply.
While at it, with regards to the attitude reset, the one holding the the full aft cyclic for 10secs, can it be done with the model static on the level ground with blades off?
Thanks for your time!
George
very cool,love it😀😀👍👍
Thank you! It’s a fantastic heli! Super easy setup
What is that old RX Model? I have a DX8 and 3 AR636B’s in planes, no Remote Ports. Need to find an older used Receiver.
Ok figured out I can get an SRXL2 for $45. Serial Micro Receiver With Bind Button. 😊
unfortunately you can not use a SRXL2. it has to be a regular DSMX satellite. you can use a AR6210 or get a Kensun DSMX satellite with a bind button.
@@westhobbiesrc8051
Thanks. Working with the Next SIM first.
I have mind setup on opentx, I have a switch which is effectively throttle hold, it just switches between 100% flat line and 0% same pitch curve in both. balls out 🙂
Nice, a lot of guys like OpenTX, I have a TX16S but nothing compares to my IX12! 😁
@@westhobbiesrc8051 nah I'm done with spektrum, seen way too many issues :(
@@DorsetSaferRoads I’ve been flying spektrum for over 15 years, never a single issue! Can’t say the same with other radios.
@@westhobbiesrc8051 there are plenty that have had no issues with spektrum but have seen too many issues myself mostly losing bind and refusing to rebind.
Had a play with an nx8 recently, the UI was slow, laggy and loads of "screen rip" the case felt horrible and cheap. Something you could forgive on a £150 radio but not on something twice that price. The ix 12 is a £660 radio. Which is mental in today's world
@@DorsetSaferRoads 99% if people problems with spektrum is they use cheap Chinese receivers which are crap and lose bind or refuse to bind exactly what you were claiming. There is a reason I fly spektrum in my $20,000 plus turbines or 300mph plus speed planes. If you use genuine receivers never have an issue. But everybody is so quick to bash or blame spektrum themselves because they are too cheap to buy an actual receiver and don’t have any idea why it loses bind or fails. I’ve had three gimbal springs brake on the TX16S already. They are just such a cheap crafted radio even the feel of them is cheap they remind remind me of the old Chinese cell phones from years ago. They’re a great radio for somebody that doesn’t have expensive models or doesn’t fly anything big. Definitely a great radio but if you’re flying expensive aircraft or big aircraft you need reliability. Flying spektrum for 15 plus years and have gone over 300mph and never a Single issue. I am more than glad to pay every penny that they charge for the radios and receivers to never have to worry and I have a peace of mind. And on top of that, they have the best customer service in the game. You can drop your radio and break it and send it to them they fix it for free. You can crash an airplane or helicopter and destroy the receiver. You send it to them they fix it no charge to you. No other company out there that’ll do that. Got a remember I’ve been in this hobby a long time I have flung every brand of radios there is. There’s a reason I go back to spektrum every time.
Are these slightly bigger than the OMP HOBBIES M2 EVO or are they the same size? Thanks in advance.
Same size as the OMP M2 EVO.
I have watched this vid again,like other vids of yours. i might of mis-understood something,when you said you are working on a rescue mode for Spektrum system will this be for the Goosky s2 OR will it work on the OMP m1 also? thanks
Thanks for always watching! The rescue will work for M1 and M2 as well as the S2! I have already tested on the M2 and M1 and working great so I’m going to be making a video soon!
@@westhobbiesrc8051 Hello, i can not find a vid about rescue mode on Spectrum ? thanks
@@Johs_Heli_Videos hello! I never did one because it’s pretty complicated. I can still do it but it’s a lot of mixing to make it work.
very great video thank you !!
Thank you for watching!
Please send me the link for your video on setting the rescue mode at normal mode.
I have a Goosky coming soon.
As of right now there is no video on rescue for spektrum yet! But very soon I have been testing and working on a file! If you set this up the way I did in the video you will have self level in normal mode and that can be used as a “rescue” but I’m building a file that will add positive pitch and upright the heli.
Please keep us up to date on that the android app is working we need a video on a general settings go throw on servos and speed and leveling the swatchplate.
Thank you for all you have done.
@@bobwatson6558 Will definitely do! They just released the ISO app! I’m in the process of downloading it and then going to play with it and then make a video!
I have a Goosky S2 and a Blade 360 smart , the Goosky seems to center itself better... Doesn't follow last command so much... The blade doesn't seem to center itself as readily as the goosky , I set up the blade as per the manual, spectrum DX7 gen 2 would you say that sounds normal when comparing the two ,I know they're different flight controllers , just wondering if I can do something to make the blade not follow last command so much... Thank you
@westHobbiesRC: I have only DSM2 Satelites around and an old DX7 radio. will it work with the Goosky S2 Legend??
Yes it will! I used a DSM2 satellite in mine for a long time. Actually I still think it’s a DMS2 satellite in it now. You will just need to bind with a separate receiver.
Thanks for the quick response. I crashed my trusted T-Rex 250 and there are almost no spare parts to be had. I think it could be a sign to get something more up to date in that size! 😀@@westhobbiesrc8051
What was the swash type? Seems kind of important
Swash type is normal, you don’t need to adjust that in the radio.
Hey Jeff, can you use a Kensun satallite like on the M2 with the Goosky? Also, I shouldn't have any issues running M2 evo batteries with my S2 right? Thanks!
Yes, you can run the Kensun in the S2. No, you won’t have any issues running the M2 EVO battery’s in the S2.
@@westhobbiesrc8051 perfect thanks for the help as always!
Hey man great video! Just curious, I’m your vid you only use the spektrum satellite for binding and then remove it after that’s done but all the other videos I’ve seen they mount the satellite receiver to the heli and keep it connected. Is there a reason for this? Thanks heaps
Thank you! I leave the satellite, I unplug it from the RX I used for binding and plug it back into the FBL.
Hi! I just got one, thanks for the video! You always help me! My futaba doesn’t have the option function, so my ch5 always going to be gyro. So, how can I do it? I noticed if I change value from avcs to normal it changes the modes, however, if I put gyro as inh, I don’t know if its going to be functional for gains, because it would be always in 3d, thats fine, but the gyro sens would work? Thank you so much. Nobody uses t10j anymore, i need to upgrade.
so I don’t know futaba anymore. been a long time since I’ve even played with one. but you don’t need to control gain. CH5 just needs to see a +100/-100 value to work the Auto level. +100 is on and 0 or -100 is regular mode.
@@westhobbiesrc8051 Perfect, its exactly how I'm doing. Actually >0 AVCS is autolevel and
Hi, great instructs. How many channels used for the S2? For the t16s, are ch 7, 8, or 9, active? Thanks..
Like all helicopters you’re gonna have your channel 6 standard. And then I’m assuming 7 and 8 would be for rescue. Thank you! I plan on setting it up to the TX16S and making a video very soon.
@@westhobbiesrc8051 Thanks for your reply. I guess in time more info will be available. Looking out for your video on this.
@@westhobbiesrc8051 Guess you never got around to setting up the Goosky on a TX16S. Just purchased the Goosky and a TX16 running EdgeTX. Would be nice to have seen a setup from you. Was flying helis years ago on Spektrum but haven't done so since 2012. Gave the DX8 to a friend way back then. I have a couple of my flybared Align450's flying with the TX16 and gonna try the Goosky setup in a day or two. Was looking forward to seeing how you setup Rescue etc. Nice vids BTW
@@rydfree Unfortunately no, my TX16S started giving me a bunch of problems and crashed two helicopters so I quit using it. The set up for the S2 is identical to the M2 video. So you can use that. I personally prefer spectrum transmitter‘s over the radio master for multiple reasons but reliability is the biggest one. I’ve had quite a few issues with it that I just fixed and never mentioned but once I crashed a couple helicopters from the radio losing RF and going into failsafe that was enough for me. Thank you.
Wow, only 40 throttle for normal mode? Seems kinda low.. I'm waiting for AMain to get these back in stock, then I'm getting one. (I want a white one to match my lil S-1, and they're out of em.)
Nice vid, do u know what type of amps the ESC is pulling for this heli?
Thinking of switching out the XT30's for mu trusty JST connectors ;)
Thank you, so personally I don’t use or like JST connectors. I’ve had one to many melt. I would highly recommend leaving the XT30. It’s a far better connector. I’m not sure on Amps.
Hey Jeff! I am interested in getting into a GooSky S2 to start back into helis. I fly with a Futaba 18MZ for my fixed wing stuff. I can't find any good Futaba setup guides. I scanned the QR code for the T16SZ which is close to the 18MZ (same menus etc) but it's mostly Chinese or something. Any ideas where us Futaba folks can get better info on the setup? You would think that a company that their reciever is using a Futaba protocol would have tons of setup info. Thanx for your help and great videos 🤌🤌👍
so , this set up will work as well with DX9 radio ?
Yes it will!
@@westhobbiesrc8051 thanks.
Did you end up keeping idle up 1 at 65% and idle up 2 at 90? I ordered a s2 and it should be here in a couple days. Very excited.
Yes, everything has been kept the same as this video.
Can you use the Kensun with bind button on this?
@@ctfirepitpistolandcigar512 yes you definitely can!
Sorry to keep bothering you but what did you set for flight mode setup and channel assign as. Thanks
You have to assign channel 5 which is the gear channel to your flight mode switch or whatever switch you want to be auto level. It needs to see a positive 100 value to be on and a zero or -100 to be off.
@@westhobbiesrc8051 thanks again for all the help. I'm still a little new to some of the heli stuff.
@@stevenhurlocker6061 anytime! I’m glad to help, we all need to learn some time and it’s always great to have someone tech it that knows a little lol
Any rescue mixing yet? Get videos!!
Thank you! Yes, I’ve got rescue to work but it’s very complicated so I need to try and make it easier.
@@westhobbiesrc8051 I will be waiting thanks!
Any progress on the rescue for s2 yet?
I see they have the iPhone iPad App now.
Yes they do, it’s been out for a little while now. Works great!
Hello, would this work with a Crossfire rx? Did anyone test this?
I’m not sure, I would think so. It’s SFHSS protocol to bind with internal RX or there is a Sbus plug on top.
@@westhobbiesrc8051 thanks!
hello,will you rescue mode for spektrum be for the lastest high spec tx like yours? will the older DX7/8 be covered? Also for a novice like me actually seeing the settings was very good. would you be able to do a similar vid on duel rates? never quite understand them regards setup
hello! So technically speaking yes it should work on any spektrum radio. It will look different but I can actually even do a set up on a DX7! I have a DX7, DX9 and IX12 so I will be sure to test all three of them and make sure they all work the same. Because I fully understand that everybody has a expensive fancy radio like mine. I flew a DX6 then a DX7 then DX9 for 7 years then went to the IX12. Yes I can make a separate video on understanding Duel rates.
@@westhobbiesrc8051 Thank you very much for listening to a request for help ,let alone offer to help. looking forward to it.
@@garymurphy5133 You’re very welcome! When I started this channel a year and a half ago I wanted to be one of the only channels that replies to every single comment and does my best to help every single person that I can! Because there is way too many people that just post videos but actually don’t do anything for the community or help the people that don’t understand.
@@westhobbiesrc8051 Fantastic attitude and goals for posting your Incredible Videos Jeff! On behalf of all who watch your Videos for the Instructional part of them, Thank you very much!! I also appreciate your Flights because of your Skill Level and Novice Pilots can see what these and other RC Helicopter's are actually capable of! People definitely need to show even the 200 Size Heli's the Respect that they deserve, in 1 second a Novice Pilot can go from Hovering to a serious cut!
Take Care, Best to You and your Family and Stay Safe my friend!
Is this set up good for someone new in the hobby?
Yes definitely, you just might want to add some expo to your aileron and elevator.
@westhobbiesrc8051 thanks so much for replying!
@@gpxrp7520 you’re welcome! Thank you for watching!
Use John Salt’s beginner setup. It allows you to dump the collective and set it down easy
Thank you for the video. My controller is spektrum nx8e mode 1 and can I connect with Goosky S2 ?
Thank you for watching! You just need a DSMX satellite.
Whats the correct satellite for the nx8+?
@@Atreyu285 any DSMX satellite. I would recommend the Kensun DSMX Satellite.
My s2 rtf straight out of the box has a tail drift... how do I get rid of this please and thank you Dave
Not sure but try using the trim on chanel 4
Hey guy thx for the video! I just got the ix14 and the goosky s2. Which newer model Satellite’ (?) I think was the word u used? Should I get now to make these two work? I’m assuming the 6 inch extension doesn’t come with it either?
And does the newer receiver come with a bind button now?
Hi Dose Anyone know how to setup rescue bailout on spektrum tx please ? Thanks Wayne
working on that now. It’s pretty involved, lots of mixing
Will the Spektrum DSMX remote receiver P/N SPM9745 work for binding it. Thanks in advance.
So that’s just the satellite, you need to bind with a Regular RX with that satellite. You can get the Kensun satellite that has a bind button.
Thank you so much for the help.
@@stevenhurlocker6061 you’re welcome! Glad to help!
IOS app is available now
Yes it is
U da man
android is better than iphone 🙂
Never! Android is a thing of past, no one like them dinosaurs 😂
@@westhobbiesrc8051 no way 😁 iPhone horribly restrictive and expensive 😁
lol... Apple stole most of is features from android open source code.... but pick what you like...
4 minutes???. I ran it for 4 minutes ok 100% and the volt got to 2.8 per cell
Yeah I land around 3.2v per cell. I fly mix for 4 minutes and if I’m running 100% throttle I land around 3:30
I wouldn't switch to an iPhone either, no thank you on the crapple products lol
I would switch to android either so… no thank you lol