Formula To Get TAKEOFF 90 & 45 Degrees Elbow LR
HTML-код
- Опубликовано: 6 окт 2024
- Piping,Welding,Non Destructive Examination-NDT
Common Piping Angles and their Solutions,Known and Unknown Angles and Angle Chart,Solving Rolling Offsets,mitered Pipe Cuts,Multipiece Mitered turns, "Y" Layout,90 deg. Saddle on (tees) Standard Weight Pipe,Pipe Circumference Divided into Equal Parts,90 deg.on (tees) extra Strong Pipe,90 deg. Eccentric Pipe Intersections, 45 deg. laterals,Concentric and Eccentric Supports on 90 deg. Long Radius Elbow,3 Types,Angle between Bolt Holes of Flanges, Pipe template layout,orange Peel head layout,Concentric Reducer Layout,Eccentric Reducer Layout,laying out Bolt Holes in Flanges,laying Out Ordinate Lines and lengths,Tank coil layout,Angle Iron Miter Cuts and Brackets,Special Offsets and Solutions,Slip or Spectacle Blind Data,Centers of Eccentric reducers and Eccentric Flanges,Centers of 15 deg.,221/2,30 & 60 deg. Butt Weld Elbows from 90 deg. Long Radius Elbows,Pipe Thread,Dimension of Weldolet on Pipe, Dimension of Socket Weld & Screwed Fittings, Dimension of Flanges Cast Steel Valves,Dimension of Flanges Cast Steel Fittings,Commercial Pipe Sizes & Welding Fittings,General Dimension of Welding Fittings,General Dimension of Forged Steel Flanges,Bolt,Gasket & Ring Joint Number Charts,Wrench Sizes,Drill Sizes for Pipe Taps,& Tap Drill Size Charts,Bolt Charts for Orifice Type Flange,Outside & Inside Diameter of Pipe& Flange Bores,Comparison Chart for Packing & gasket materials,Hand Signal for boom Operated Equipment,Hand Signal for Overhead & gantry Cranes,Useful Information,Pipe Expansion,Pipe Bends,Circle,Inches&Feet Converted to millimeters,Conversion Constant,Decimal Equivalents,Fractions& millimeters,Safe Loads,for Wire and Manila Rope Charts,Decimal of a Foot,minutes converted to Decimals of a Degree and trigonometric formulas,Pipe& Water Weight Per Line Foot &Feet head of Water to PSI,Wire bending,Symbols,Computation.
Playlist:
Pipefitter Works • PipeFitter - Piping Works
How to Read Isometric Drawing? • How To Reading Isometr...
Angle Computation? • Pipefitter Angle Compu...
Welding Works? • Welding
Pipe,Welding,Non Desructive Examination-NDT • Pipe,Welding,Non Desru...
How come you multiply mm to inches, in multiplying different unit you need to covert either one of the two. 38.1mm x 10 inches this is what you did which is wrong . I hope you rectify your explanation.
1.5 X diameter of pipe X 25.4 ( to convert it to MM ) = Take off in MM . Lols di mo gets ? Hahaha
Easier way is to break the OD in half 4 times add 1 and 2nd number for 90, add 2-4 number for 45 .
So 12,6,3,1.5 … 18 “ is takeoff for 12 lr 90,
Another example , 6,3,1.5,.75, 3.75 is takeoff for 6 inch 45.
Nice job
Cool content i like it bro very good
I appreciate it
For 90s: Long radius is x1.5 of pipe diameter. Short radius IS the diameter of pipe. So a 6" 90 long radius has a 9" takeout. A 6" 90 short radius would have a 6" take out. Simple. Not complicated
Good 👍
Magandang araw kabayan. Matagal na akong laging nakasubaybay sa mga lecture mo. Ako po ay Quantity Surveyor Pero Wala po akong alam sa sa piping. Pwede po bang mag paturo kung paano mag estimate using inch dia at inch meter at paano piniprepare para sa reporting. Yan po kasi ang tanong sa akin ng interviewer na Hindi ko nasagot. Salamat kabayan at saka God less.
contact me 09631285004
Dude, why make it SO complicated? Very simple. 1.5 X pipe size. ex. 6" pipe, 6"× 1.5= 9".
Tan45*1.5*6*25.4 simpal
Kino convert kase sa MM kaya yung take off na naka inches multiply lang sa 25.4 anong kumplikado dun ? Lols .
Gruvlok elbow formula plz
bro pag long radius multiple ba sa size ng elbow.pag short radius as is n ang constant wala n multiple?
Tanks from lraq
Thank you
for 45 just nps x .625
Nice.. thanks
15.8mm x 10 inches= 158 mm??
boss baka pede nyo ma share san ba at panu nakuha un take off na 38.1 sa 90 at 15.8 sa 45 elbow.. gusto ko lang talaga malaman may list na ako dati nyan kaso nawala sya at di ko natandaan
yang 38.1mm na convert yan mula sa 1.5 inch (1 inch = 25.4mm). Bali 1.5 x 25.4 = 38.1mm, the same sa 45 elbow 5/8in or 0.625in, 0.625 x 25.4 = 15.875
Boss 38.1 mm x 10 inch
The 10 inch no need to convert to mm thanks if you answer may Q
Boss ang formula kase is . 1.5 inch X 10 (diameter of pipe) X 25.4 = take off in MM .
Ang ginawa nya is ganto . Inuna nya yung 1.5 X 25.4 = 38.1 . So to convert the take off of 10 inch to MM simply multiply 38.1 X 10 = take off in MM . I hope naintindihan mo po
Sir. Unequal leteral tee for any Degree formate bataye plz
Hay naku si kabayan...
mm x inches = mm?
Ganun pala yun?
Hay naku kumikita na naman si kabayan ng 38.1× inches = mm
Ser saan galing ang 38.1
i m confuse... messy explanation
Its not center to center, it is center to end.
Sir saan ba galing ang 1.5?
Raduis of the 90 degree elbow, R= 50% of diameter of the elbow + diameter of the elbow. R=.5d + d; R= 1.5d.
kulang pa aking nalalaman sa PIPEFITTER gusto ko malaman lahat PIPEFITTER din ako?
stay tune bro
Sasaw man mu-explain dili han-ay.
Hindi me bhi batane ka kosish karo na sir
Ayusin mo ang paliwanag mo pre, tingin ko nalalaman mo lang yan sa actual work hindi sa pag aaral. Mahirap intindihin kay sa tunay na english. Parang masmadali intindihin ang tunay na english lesson.
Not clear explanation.. Can you make it simple. Coz your have difficulty on your english
Ang gulo ng explanation mo sir,
Ang gulo ng explanations mo
Hahaha try to actual than to explain in the piece of paper
bogo
Waste of time