If you remove the inner fender liner first, you can then use needle nose pliers on the backside of the retaining clips with the slightest squeeze and you will not break a single one when removing fender.
This could be the best drinking game of all time! Every time he either says "went ahead or go ahead" .....but you better just do a shot of beer cuz you're going to have a nasty hang over!
It’s less than the front for sure, you definitely gain more clearance but not like what you see in the front. Your results may vary depending on your lift, mine leans to the passenger side a decent amount. Hope this helps, thanks for watching!
I did the wiring a couple weeks before the install video, I basically found a picture of the halogen and the led and made sure the wires went to the same place on the new plug. If your buying the fenders new there is no wiring necessary, it’s plug and play. The reason I had to make a harness was because mine were used and the factory harness was cut up by the turn lights. Hope this helps, thanks for watching!
I’m not sure, I know the dealership sells them as a complete kit with the fenders. I would check eBay or Amazon for a replica fender liner or you could check if a local body shop can order them for you. Hope this helps, thanks for watching!
I’m desperate to find that moles connector. I have no idea where in the moser website to find it and search 6 pin or Jeep JL didn’t help. Can you possibly attach the exact link for the part. Thank you in advance
I did a lot of research to find out what went where. I found the wire diagrams on one of the Jeep forums, it’s been awhile so I don’t recall which one. I’ll try to find a link if I can.
Yeah they will go on just fine, there is a gap but it’s not too unsightly. I ran it that way until I switched to an aftermarket bumper. Thanks for watching!
Can I ask what offset wheels you have here? I'm going to be upgrading to rubi flares soon, currently getting my wheels n tires on sport axles. Much appreciated
I also got the fenders off a rubicon and wired were cut like yours where do you buy the wires you need also I have the led package just didn’t come with the fenders..
Valdemar Quidera having the LED’s already is nice, you won’t have to reprogram. I just bought 22ga wire off Amazon I’ll put a link in the description if that helps.
HighPoint Overland thanks, I’ll definitely check it out. To reprogram I used the JScan app and the Chrysler specific wire and Bluetooth dongle. There are a few people using it that have done videos already. If you want more info on the parts I can put links in the description.
I did a lot of research on the forums and ultimately looked at pictures between the two to figure out the order. I did find one write up that was very helpful I’ll try to find the link.
If you buy the fenders from the dealership it will be plug and play. You will need to get a programmer and tell your computer you now have LED fenders. I had to wire mine because the harness was cut when I bought them second hand. Hope this helps, thanks for watching!
@@FROSTBITEOFFROAD do i need a bypass cable or just the adapter and how do i program the led fender??sorry this is my first jeep thats why im a lil bit confused.
@@melvinsaturno5670 no worries, you have to buy the Chrysler specific cable and the Bluetooth dongle to connect to the app. The cable is plugged in behind the OBDII port to bypass the security on it. There is a video on it here somewhere I’ll see if I can find a link for you.
Why don't these videos ever show someone installing the new clips on the fenders? That's the hardest part of the job. It would be nice to see an easy way to do it.
Thanks for the great content, and keep them coming. I have a 19 JL sport, and it didn’t come with the led package. If I get the High top Rubicon fenders from mopar will I be able to install it with the same connector or do I have to rewrite the connector. If I need to rewire it do I need to install any other LED harness in the Jeep for the computer to know it’s LED? The reason I ask you s because I saw a LED harness on the mopar site and not sure if it was related. If I can rewire the connectors on the fender and be set after flashing I’ll be relieved. Thanks for your help! And keep the content coming
Thanks for watching, I had to re-wire mine because it was cut when I bought the fenders. If you buy them new they are plug and play! You do need to get a Tazer and tell the computer you have LED fenders or they will hyper flash and stop working after a few tries. Hope this helps!
Glad to see you spell your name right ;)
Thanks Bryan 🍻
If you remove the inner fender liner first, you can then use needle nose pliers on the backside of the retaining clips with the slightest squeeze and you will not break a single one when removing fender.
D Wax I’ve heard of that working, but I already bought all new clips so i wasn’t too worried about breaking the old ones.
This could be the best drinking game of all time! Every time he either says "went ahead or go ahead" .....but you better just do a shot of beer cuz you're going to have a nasty hang over!
Or every time I say “you guys” you would have one heck of a buzz!
so you get half inch in the back with Rubicon finder
thanks for the video
It’s less than the front for sure, you definitely gain more clearance but not like what you see in the front. Your results may vary depending on your lift, mine leans to the passenger side a decent amount. Hope this helps, thanks for watching!
Hello I would like to know how to do it in the jscan app I really don’t know what to do in the app
If you go under the adaptation tab, there is a LED lighting tab where you can add the LED turn signal function. Hope this helps, thanks for watching!
How do you know which wire is which?
Whats the wheel offset for the silver jeep
The wheels I had then were the Procomp Prodigy 17x9 4.75 backspacing. Hope this helps, thanks for watching!
I just swapped out my end caps on my Sport S for the Rubicon ones. This in preparation for installing the Rubicon fenders this week.
Russ Elmy yeah I’m on the lookout for a Rubicon rear bumper. They gap is pretty noticeable on the rear.
@@FROSTBITEOFFROAD If you have a 3 piece plastic bumper you only need the end caps a support brackets. easy swap
Russ Elmy yeah I do have the 3 piece one, I kinda want the metal one but I need the backup sensor holes. I’ll keep an eye out for both, thanks!
Can you give the link for the end caps?
could you share more about the wiring ? i have a sport too, been looking to upgrade to Rubicon fender with the look of DRL . thanks
I did the wiring a couple weeks before the install video, I basically found a picture of the halogen and the led and made sure the wires went to the same place on the new plug. If your buying the fenders new there is no wiring necessary, it’s plug and play. The reason I had to make a harness was because mine were used and the factory harness was cut up by the turn lights. Hope this helps, thanks for watching!
@@FROSTBITEOFFROAD thank you very much for this informative message!!! that solve a lot of my questions
@@mbperfection no problem, enjoy the new fenders!
You know where i could get rubicon inner fender liners?
I’m not sure, I know the dealership sells them as a complete kit with the fenders. I would check eBay or Amazon for a replica fender liner or you could check if a local body shop can order them for you. Hope this helps, thanks for watching!
Where did you find the Molex Connector? Thanks
Mouser Electronics website, they had everything I needed to fab up that wiring harness.
I’m desperate to find that moles connector. I have no idea where in the moser website to find it and search 6 pin or Jeep JL didn’t help. Can you possibly attach the exact link for the part. Thank you in advance
Sorry for the misspelling. Molex / Mouser
Hard to see in vid, what color wires connect to each other when splicing.
I did a lot of research to find out what went where. I found the wire diagrams on one of the Jeep forums, it’s been awhile so I don’t recall which one. I’ll try to find a link if I can.
www.jlwranglerforums.com/forum/threads/factory-led-package-drl-turn-signals-awol-part-numbers-fighting-with-dealership.10616/page-8
Do you know if the rear fenders will still go on with the one piece sport rear bumper?
Yeah they will go on just fine, there is a gap but it’s not too unsightly. I ran it that way until I switched to an aftermarket bumper. Thanks for watching!
Hi do you have a link for the connectors I’m trying to do the same procedure on my JL thanks
Mr. chito www.justforjeeps.com/68395634aa.html
Do you know how wide they are compared to a sport fender flare? Would be much appreciated
They are 3/4” wider that the Sport fenders. This is to match the wider axles the Rubicon’s come with. Hope this helps, thanks for watching!!
Thank you so much! Really appreciate your reply. Btw, awesome Jeep 👌🏼
@@jonnyfsilvers no problem, thanks man I enjoy it!
Can I ask what offset wheels you have here? I'm going to be upgrading to rubi flares soon, currently getting my wheels n tires on sport axles. Much appreciated
@@jonnyfsilvers hey Jonny, my wheels are 17x9 -6mm 4.75” back spacing. I hope this helps thanks for watching!
I also got the fenders off a rubicon and wired were cut like yours where do you buy the wires you need also I have the led package just didn’t come with the fenders..
Valdemar Quidera having the LED’s already is nice, you won’t have to reprogram. I just bought 22ga wire off Amazon I’ll put a link in the description if that helps.
Frostbite JL how did you reprogram? My JL is a sport without led or drl. Great channel! Check mine out if you have a chance.
HighPoint Overland thanks, I’ll definitely check it out. To reprogram I used the JScan app and the Chrysler specific wire and Bluetooth dongle. There are a few people using it that have done videos already. If you want more info on the parts I can put links in the description.
Frostbite JL very cool! Thanks for the info.
@@FROSTBITEOFFROAD please share a link on how to reprogram for LEDs if you can. I have the same JL SU none LED fenders.
I have Jeep rubicon none led but I am going to contact my none led wires to led lights can you help me out please thank you
I did a lot of research on the forums and ultimately looked at pictures between the two to figure out the order. I did find one write up that was very helpful I’ll try to find the link.
Are you building a wire harness like I did or simply swapping led fenders for your factory ones?
@@FROSTBITEOFFROAD yes please
I need to get the molex connector send me the link please
@@eztrailsoverland1899 message me on Instagram I’ll send the pictures over.
I have a 2020 jlu sport s with led headlights. Will it be plug and play for it or i still need to wire it?? Thankyou for the help
If you buy the fenders from the dealership it will be plug and play. You will need to get a programmer and tell your computer you now have LED fenders. I had to wire mine because the harness was cut when I bought them second hand. Hope this helps, thanks for watching!
@@FROSTBITEOFFROAD will obd jscan work?
@@melvinsaturno5670 yeah that’s what I used, just make sure to buy the appropriate cable and dongle.
@@FROSTBITEOFFROAD do i need a bypass cable or just the adapter and how do i program the led fender??sorry this is my first jeep thats why im a lil bit confused.
@@melvinsaturno5670 no worries, you have to buy the Chrysler specific cable and the Bluetooth dongle to connect to the app. The cable is plugged in behind the OBDII port to bypass the security on it. There is a video on it here somewhere I’ll see if I can find a link for you.
Where did you buy this from?
They were a Craig’s List find.
How many inches of suspension do you both have?
Gabriel Cruz I have a Metalcloak 2.5” lift.
Good, with 37, nice
Why don't these videos ever show someone installing the new clips on the fenders? That's the hardest part of the job. It would be nice to see an easy way to do it.
Thanks for the great content, and keep them coming. I have a 19 JL sport, and it didn’t come with the led package. If I get the High top Rubicon fenders from mopar will I be able to install it with the same connector or do I have to rewrite the connector. If I need to rewire it do I need to install any other LED harness in the Jeep for the computer to know it’s LED? The reason I ask you s because I saw a LED harness on the mopar site and not sure if it was related. If I can rewire the connectors on the fender and be set after flashing I’ll be relieved. Thanks for your help! And keep the content coming
Thanks for watching, I had to re-wire mine because it was cut when I bought the fenders. If you buy them new they are plug and play! You do need to get a Tazer and tell the computer you have LED fenders or they will hyper flash and stop working after a few tries. Hope this helps!
@@FROSTBITEOFFROAD Most definately, Thank you!
@@FROSTBITEOFFROAD did you need to replace the fender liner as well or can you use the same ones from the stock fender flare?
@@masumchoudhury the new fender’s actually come with new inner fender liner’s already attached, so it makes it really easy!