Honda EU2000i - Ultimate Ignition Troubleshooting and Repair
HTML-код
- Опубликовано: 11 май 2022
- Today we will be troubleshooting a no-spark condition on this Honda EU2000i inverter generator. This was a complete restoration, during which it was discovered there was no spark. The standard troubleshooting steps were conducted to bring this specific problem to resolution.
Honda EU2000i Generator, Maintenance Tune Up Kit, Filters, Oil, Spark Plug, Fuel Filter
amzn.to/3yPAgNQ
#hondagenerator #generatorepairing #diyrepair Авто/Мото
One of the best videos I have ever watch on RUclips. This guy is straight to the point, very detailed, knowledgeable, and through. Will definitely be subscribing to his channel.
Just wanted to say how helpful it was that you showed how everything was put back together.
Glad to hear it helped.
Top Dog you are! not a single U Tuber vid on these generators even comes close.
Thank you.
Only 1 thing I saw left out was the screw in the air filter housing. But excellent video.
This was great! I'm so glad your workbench is messy like mine! If it was spotless, I would doubt the information's authenticity....
I’ve watched several similar videos. This was by far the most helpful both as to the testing procedure and the disassembly. Now think I can finally repair mine and put it back together afterwards. Many thanks.
Great to hear!
You are really a professor
Hello from the west of Algeria
Thank you.
VERY nice video. Thank you! 👍😎
Great job! Thanks for all the details and clear instruction you give.
Excellent presentation. You helped me get my generator back in the game. Thank you, good job.
I'd like to thank you for a good demonstration but most of all honda for building a fine machine that is built to be repaired and serviced bythe owner.
Copmplimenti, non è facile fare questi video di smontaggio !😀
Very useful video, thanks.
Did you ever do a video for an oil sensor change?
Very good video! helped me get a spark after 2 minutes. The only think I noticed, you closed the airbox cover before bolting the screw in the airbox into the block and than installed it only with the two nuts on the carburetor. Odd.
The device at the time was in several states of disrepair as you'll see in the restoration video. Some footage was made as I was addressing only a specific issue at the time.
@@delorean1 Again, very good informative video. It helped me diagnose no spark. Your other video helped me with a gooey carburetor. Thank you for sharing the knowledge!
I have 3 of those generators. At a certain point I used them on my semi trucks to power portable air conditioners. This was when the new emission came out and idling a big diesel would clog a DPF. I built cages for them on the frame behind the cab and added an external aluminum fuel tank. I used it for about one summer before ditching the idea since those portable home AC were not designed for a vibrating vehicle and I went through several under warranty. Those gensets remained on the trucks for 2-3 years out of laziness before I removed them and stored at my storage. I just rebuild one (mainly plastic part, very bad fuel system, oil, plug and filter) and have no energy for the remaining two. Let me know if you're interested in buying them cheap.
Great video. Have you run across this problem that I can't seem to fix with the many internet 'common problems' of the EU2000i. The ECO switch does not kick down the rpms. And the motor runs rough without achieving full rpms. In other words, turning the ECO switch 'on and off' does not change the rough rpms, however the switch is fine as tested with an ohm meter. Carb's cleaned, but I also replace with a Chinese knock off a couple years ago and was running fine. I still have the original. Yes, the generator has had its issues, with less than 500 hours. So much so I've replace it with an EU2200, but am still up for a challenge!
Great video, very helpful!
Very well done.
Thank you for your time and consideration in making this very detailed video. You are appreciated!
My pleasure!
This was an excellent video I'm currently working on a Ryobi 2200 don't know how a generated the signal for the spark that this is very very helpful your presentation and how you feel about the video with the exact information please specifically very very much appreciated I'm here in the US Virgin Islands and we are limited to the texts that are available for some of these items
Thanks for sharing your knowledge / experience with us!
My pleasure!
I enjoy your style of video. Excellent content.
Hi my question to you is if the ignition coil reading on the primary is 0 will that cause the engine to just die and I couldn't restart no spark at the plug changed plug still northing so checked reading coil secondary is good but primary is 0 Oil sending switch checks oil. Thanks Rick
Hello, would you know the Ohm spec of the Pulse Generator on a Honda EU1000I A2? I have a weak and intermittent spark. My PG ohms out at 30ohms. 270 less than your measurement on this EU2000I video. Looks like I am only making .25mv on a pull but not sure I was pulling my friend was watching the MV All wiring has good continuity. Ignition coil resistance in spec. With no way to check the module I am hoping the Pulse Gen Is NG. Thank you!
thank you
You're welcome
How do you test throttle motor and eco switch? I bought a new carburetor and the plug is square not flat
Did you torque the spark plug. I replaced mine and found it very different with the compression washer? Makes me wonder if it is tight enough?
The compression washer is scary because you think you are stripping out the head, but eventually the torque will increase as it bottoms out.
I have 2 identical EU2000i generators, I have a no spark condition on unit number 2. The coil measures 1.7 on the primary. I replaced it with a working one from unit 1 and still no spark. The pulse generator measures 340 ohms at the ignition module and at the 6 pin connector. And I get voltage with a pull on the cord. I swapped the ignition module into the working unit 1 and it works. Tested the oil switch and engine off switch. All work. Replaced the spark plug. No spark. All measurements at the ignition module read correct. Before I tear down to get to the pulse generator is there anything I can try? Thanks for your video.
I did post all of the troubleshooting steps.... whatscha got left?
Anybody heard of one creating some pretty heavy duty sparks from the inner/plugs area?
Mine 'sparked out' today and now the motor runs but no power to power points! 😕
how do you check if the carby's blocked???
Brake cleaner and compressed air.
Any chance you could do a similar video on kipor ig 1000. Wire colours and part names are too different.. Hello from ireland
Sorry I do not know of this model.
When I try to turn the eco button on nothing happens. I replaced the eco switch but still the eco mode doesn't work. Do you know what could be the problem?
Check your "Throttle control motor"... sitting under the white plastic case on top of the carburetor...
@@Horus2Osiris okay but how do I check it? I mean what am I looking for?
A lot of the components are very similar to the EU1000i generator.
I wasnt aware, havent worked on that model.
What can cause no pulse at the fuel pump?
I do have good engine compression
That hose to the pump could be broken or not correctly fitted to the engine./
Your too advanced for us. Water it down. Pretend your talking yo 14 year olds