How to Replace Fuel Injector 1994-2004 Chevy S-10
HTML-код
- Опубликовано: 8 сен 2024
- Buy Now!
New Multiport Fuel Injection Conversion from 1AAuto.com 1aau.to/ia/1AFI...
The fuel injector is responsible for delivering fuel to the intake ports or combustion chamber of your vehicle. If it is not working correctly you may find your engine running poorly. This video shows you how to install a new fuel injector on your 1994-2004 Chevy S-10.
• Check here for more videos on the 1994-2004 Chevy S-10 • Chevy S-10 2nd Generat...
This process should be similar on the following vehicles:
1994 Chevrolet S10
1995 Chevrolet S10
1996 Chevrolet S10
1997 Chevrolet S10
1998 Chevrolet S10
1999 Chevrolet S10
2000 Chevrolet S10
2001 Chevrolet S10
2002 Chevrolet S10
2003 Chevrolet S10
2004 Chevrolet S10
Tools you will need:
• Flat Blade Screwdriver 1aau.to/ori/1AX...
• Pocket Screwdriver
• 10mm Wrench 1aau.to/oeL/1AX...
• 10mm Socket 1aau.to/ooD/1AX...
• 8mm Socket 1aau.to/ooD/1AX...
• Ratchet 1aau.to/osH/1AX...
• Socket Driver
• Socket Extensions 1aau.to/oro/1AX...
• Torque Wrench 1aau.to/okA/1AX...
• Paper Towels 1aau.to/ocz/1AX...
Subscribe: / @trq
Check out our playlist:
Chevy S-10 2nd Generation 1994-2004: • Chevy S-10 2nd Generat...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Best vortex upper manifold and injector vid by far, and only 24 likes..
I agree man I looked through so many videos and this one was the ONLY one that was thorough and extremely informative. Big up!
👍
Hi i enjoyed this video very much help for me i hav 1994 s10 Auto 4.3 eng v6 i was woundering is the wire harness pretty much same ? I hav Alot of messed up wires and connectors tht i am going to try to do myself .they just look different from mine .what do i start w first well thank u I'll be subscribe ING to yr channel thank u
04 chevy s10 4.3 ls
Great instruction, I followed step by step and completed the whole job in about 4-5hrs, surprised how smooth it all went, thank you so much for the professional video, I saved myself about 450$
Note to public* mechanic work takes patience
Being mechanically inclined helps!
Doing this with my 2001 Sonoma
I am definitely not mechanicly inclined but I'm definitely trying!!
Your channel is awesome, no useless chit chat or annoying intros.
Thank you
The fourth time you said, 'set aside' was my cue to take my car into the shop
I'm going to be starting this project on a 2001 Blazer this afternoon. This is one of the best videos I've seen for a project this in-depth.
Yesss it is and he does it with GööD LIGHTNING 💡 VERY AWESOME
How'd it go
Let me say this. You are the man. You didn’t start out with a bunch of junk at 1st. This video had Good LIGHTING!! and you said what components were. And the torque sequence of what to do and you did and torque specs. You saved me $$$$ THANK YOU THANK UUUUU!!!! This video is ⭐️ ⭐️⭐️⭐️⭐️
Great! Now that I watched the video I’m ready to take it to my mechanic
You are a phenomenal instructor. Thank you for taking the time to show us. I’m going to use this knowledge to help our son maintain his grandad’s old 2003 ZR2. It’s been a struggle keeping it on the road.
+pterion34 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
J
Very clear and straightforward instructions, great job!!
Yoooo your video is very descriptive I was doing this job and put it on pause but now after this I’m all gas no breaks foward
today i tried to change my injectors. it was hard to install with hard plastics line. I finally put everything back together, and now my truck is running extremely rough, and misfiring.
Just bought a 97 ZR2. I'm becoming a big fan of this channel. Thanks for the quality work.
I concur best video on vortex plenum (upper manifold) I've seen. Thank you and aloha.
I hope I can do it as easy as you made it . I am fixing to change mine thanks for a very explained video
Thanks your sequence is spot on. My only comment is the new style spider legs are really, really stiff and difficult to maneuver compared to the old simple one line poppet lines. It was a battle getting them routed under the bracket and it took a lot of muscle to get the module in the bracket. Be prepared to be forceful, just don't break anything-it's a fine line. Good luck.
Thank you for the no-nonsense straight to it video appreciate it
Lifesaving instructions my friend! Thank you for the awesome video for those of us that's still holding on to the Chevy Blazer....LOL!👍💪
This video was exceptional. I’d already purchased the fuel injector assembly before I watched this, but I went out of my way to seek out TRQ rotors, pads, and calipers for my upcoming brake job. I can’t thank you enough. Every step was so clearly laid out. Phenomenal.
Bought one of the cheapest s10 Xtremes in my area (Florida) and from the start it had issues. It would start fine but the ideal was rough and I mean rough, changed the spark plugs wires cap, distributor etc. With no luck :(
After watching this video for about a week I figured I’ll do it myself. Step by step by far the most in-depth videos on this I’ve seen so far. Now it’s driving with my misfires and seems to run like a champ
Great video. I just bought a '99 S10 and kept hearing about this "spider injector" system. So, a quick search brought me to this highly informative video. Now, if I ever need to address this unique injector assembly, I'll have a lot better idea of what it is and the entire process. I only wish I could do it in eighteen minutes and eleven seconds! 😁
+Andrew Bolig Thanks for watching our video! 1aau.to/m/Shop-TRQ
WOW!! One of the best instructional videos I have ever watched!!
You guys are awesome. Thanks for the video.
Thank you for posting this video. I'm smelling fuel when I pulled my intake pipe.
Thank you for the help. you guys have saved me so many times
I'll tell you what. Thank you for this video. Step by step awesome I'm very mechanically inclined but I'm not a mechanic I'm a carpenter. Very good one. All I can say is thank you. It runs awesome.
Streight to the point. Well done sir...👍
+Dizzy Assklown Thanks for watching our video! 1aau.to/m/Shop-TRQ
Holy cow, you guys are awesome!
Just an FYI, the factory injectors unclip and pull out. These cheap replacements snap into place and thats it. I am having an issue with the white plastic tube, it came off the injector before it got seated. And of course the injector won't push into place. So ultimately going to have to take off the lower intake manifold and start over. You've been warned lol.
THANK YOU FOR THIS VIDEO!!! Most informative video I was able to come across.
nice video but I did all that you did and now my truck has a over fueling problem it is dumping fuel down the exhaust pipe don't know what to do next I guess I will just go ahead an put a 350/350 in the damn thing
Take the positive end off, not the negative. You remove the entire ground to the electrical system when you do it that way.
Dude you make the best videos.
Aloha from maui! Thank you so much for this video! Again very great at how your teaching ppl how to do it themselves! I followed your video and did it! Part is coming for the oxygen sensors that I gotta change today. Hopes truck will sound better. Thanks again! Love your videos! Took me 2hrs 👍
Changed this for my 2002 chevy s10 pickup 4.3l
Since you released the fuel pressure, do you need to cycle the key first then start the truck?
Should I note a really really good push to get injector to set down
this video is great!! I thank you for explaining how it comes together and how each part of the motor is identified
Хорошая работа👍
Заводится всегда и везде с первого раза))
Please do a video of the lower intake gasket manifold REMOVAL!!!! Please !!!! 🙏🏽 🙏🏽🙏🏽
Thanks man, very helpfull
Do you have to replace the intake gasket everytime you pull it?
13:48 nice tug
Thanks, can't wait to start this project
So what happens if you have a misfire. Where’s that video
It's not that hard to say the socket size you ate using tho.... really helps me know what to take to the junk yard...
Are these injectors the same on a 2002 Chevy s10 2.2L 5speed ?
If probably the best most thorough mechanic video I've ever seen. Great job! Can you troubleshoot A P0303 Cylinder number 3 misfire From the Injector plug? Which plug was the injector plug? Which tab on the injector plug do you test? Thank you. If you are an awesome mechanic
Thanks so far! But what was removed at 8:27?
Awesome tutorial the best by far👍
What would be symptoms of a failing spider? Was there a reason for changing this one or was it just for instructional purposes?
Great video. I have it playing when I started to replace my spider injector in my 2000 Blazer. Question. The replacement ACDelco spider injector came with a new bracket that looks different than the stock one. Can I use the stock one? That's what it looks like you used. Thank you
How do you keep them from crimping. I done it the exact way and mine crimped
Awesome video thank you very much !
Great video thank you
So on a 97 4.3l. There is fuel coming out of the electrical spider harness~do you think it is a cracked injector line there? Also get the engine to start we spray carb cleaner in throttle plate
My v8 is popping too. Definitely was out of time. I changed the distributor and replaced. I went with ac Delco. The other autozone stuff is made in China and I purchased a sensor brand new from them that was bad out of the box. So you could have had failed new parts for future reference
Dude how do you remove upgraded poppets
Wish they would have done a 2.2..
How did you get your injector to sit above the lip as mine would not do this
With the fuel line bro I only got one going on ??? The truck came like at but now after finishing putting a spider injector in I have a massive fuel leak at the fuel line because only one hole has a line other empty but that’s how it was before ?? And it didn’t leak now it does any ideas thanks
A few major things wrong
That Injector metering body bracket is incorrect for an MPFI swap.
You really should use a heatgun on those nylon hoses and preroute as much as possible, smashing it down in like that is a good way to warp, kink, or crack a hose.
You can use a crowsfoot socket to remove the fuel rail, and dont spray gas on the firewall like that..
I was thinking about cutting the plastic ends of the injectors in half because they seem a bit longer than necessary.
What makes you think you know better than a team of engineers and manufacturing specialists? GMC designed this as a direct upgrade for a design that flaw became apparent in. Also, if they could save some money on the plastic material, manufacturing, and shipping, they have already done a weight and material minimization.
I'm having the same issue. Did you ever find a solution? The problem is that the plastic end, for some reason, is too long and will not seat in the injector holes. I don't know if I have a different intake or something but it doesn't go in like they do in this video.
Why did You Not Clean the bottom half of the plenum??.....With a dry rag......
Hello I just replaced my 2003 GMC Sonoma and im getting like misfiring only when I step in the gas pedal do you guys know how to fix this?? thank you
Except; how did you get the fuel lines to move to the side?
Help!!!! The top part of the Pintle Tube (plastic piece that goes into the engine) is too big and can not fit. Are these "universal"? I have tried everything and none of the 6 fuel injectors are going in properly.
are the sockets used metric?
After reinstalling my second fuel line the one closer to the steering wheeling wont sit in the spider injector it keeps popping out. My other fuel line sits in perfectly cant find a solutions any ideas?
+@conormccall7557 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I'm working on a 1993s10 2.8 show me the throttle body with the 2 clip that works the gas
My mechanic said some shops won't even attempt this job because it's too complicated, it doesn't look too bad from this video (especially for a professional), why would they say that?
Thought it was 513 on the driver side
How much would it cost to have a someone do that labor for me
your using the V-6 on an 98-2005 S-10 as the air intake on a 94 is MUCH different then the one you used in the video!!! Sorry I have a factory 94 S-10 with the 4.3 v-6 and you seem to be using the engine that they put in a Blazer!
I noticed you removed 5mm injectors, and replaced them with the 6.5 mm injectors. Is there any reason for that, and does that cause a change in how it the vehicle runs?
The new nozzle on the injectors is longer because it is more recessed which prevents them from getting clogged up as easily as the original style
98 and up is different
You can’t go straight in. I believe 1 &3 cyl are swapped.
Why did he need to replace the plenum gasket
Very complicated.
Damn you GM!!🤣🤣
How are you gonna post a video without showing how to completely take the cover off u left out the only part idk how to do
Easy enough but I own an Astro lol
Almost better off switching over to the marine intake that uses multi port injection.
This video has no sound to me
Who knows how to remove a new injector? I can't unhook the nozzles of the injectors.
49
Attempting today, most of my connectors and rubber is brittle and rotted. Good luck to me! Ill repost back.
Ok, all done. No special tools required. Didn't break any connectors. Found an eroded 90° elbow on the EGR valve, (the one with the vacuum hose as well). Had to replace an o-ring for the break booster tube housing, at the plenum. She runs good and my daughter bought me a whopper for appreciation.
Background; I'm mechanically inclined, was a mechanic in the army and do most of my own repairs.
You can do it!
Do you have to replace both gaskets every time the parts are removed??
Im having trouble taking the plastic cover off. I think my injector assembly is attached to it. How do i fix this?