Using LS car intake with truck accessories - 1965 Impala LS swap
HTML-код
- Опубликовано: 19 мар 2023
- ALTERNATOR MAY OR MAY NOT HIT YOUR HOOD. It still sits tall. This is dependent on your vehicle. Be cautious! We get our accessory drive ready on our LQ9 so we can be one step closer to setting the engine in the car! All part numbers used down below!
For more constant content:
Instagram: @Mylifesucksofficial_
Part numbers
Water pump: 252-846
Water pump spacers: 551674
Idler relocation: 551353
Tensioner pulley: 38195
Idler pulley: 36299
Belt (no promises this one will work for you, best used as a guide) : K060990
Music: Evan King - Factory
/ contextsensitive
contextsensitive.bandcamp.com/ 
Авто/Мото
Where was this video when I started my build 🤦🏻♂️ I’m the dummy that bought a car intake and a new truck water pump and learned the hard way . Great video 🤠🤘🏻
Sometimes the best way to learn is the hard way!
I made a couple trip to the parts store myself.
A 2010 camaro 6.2 water pump also works for the same set up. I used one on a 1999 5.3 truck engine. I used a dirty dingo relocation kit. Smaller bell on water pump, lines up perfectly to truck accessories drive.
That’s really good to know!! Thanks for sharing!
Definitely some great information. One day I will ls swap my C10. Glad you made is so understandable.
Any questions you have I’ll be here, broski!
Thanks for painting the engine a color that stands out, if you're going to take the time to build something awesome, make it stand out
Thank you! I had the same thought. Also wanted to give it somewhat of an "original" look. I'd paint the intake too but I think LS intakes don't look all that great painted. So this will do
I have an 06 Canyon Z85 RWD 5-Speed. I have a Gen 3 LM4 on a E40 PCM. I kept the truck Setup but went with a TBSS Intake because it's just better.
The tbss is pretty much the best stock intake you can run with as long as you have the clearance. Great choice! That was my original choice before I found this one second hand
sick i've been wanting to LS swap my caprice so this def makes me wanna commit
It’s a journey that will be worth it!
Thank you so much you explained this so well and help me a lot thank you
Glad to have helped!!
Great video brother!✌️
Thank you!
Nicely done.
Thank you!
That alternator/power steering bracket cleaned up nice. What did you use?
Uhm also need longer bolts to mount Camaro belt tensioner to your new Camaro water pump. The truck one is about 3/4” too short at least the ones on my 05 LQ9 were.
I don’t remember on mine specifically to be honest if I had to change the bolts. If I did then I probably found something around the garage or took a trip to the parts store. Luckily it’s an easy thing to take care of. Definitely something to note though! Thank you!
great great info paisa!! following your build,whens the install in the bay happening?
Hopefully soon! Still needing a few more parts before I can put it in the car for the last time. Really want to hear it run before the end of the year.
your not broke! haha
Im lucky enough to have a few extra dollars to spend on these silly projects but I promise I’m no bill gates! Haha I go to work every morning like anyone else!
How many inches lower is the car intake? Does it have much of a change in the torque curve does it do? I'm putting a L92 into a jet boat and want the engine cover as small as possible . . .
I believe the car intake is right around 5 inches shorter. But I can’t confirm that for sure as I’ve only read that, never measured myself. You’d have to dig a bit into forums to double check on that, unfortunately. But I can tell you that if I had a truck intake I’m not so sure it would even clear. As far as torque curve goes, that’d be having to compare some kinda dyno sheet. But a usually the idea is the truck Intake will make the torque sooner and have less high end. Car intake will be the opposite. Could make the same torque but will be at a higher rpm.
im at this cross road and can't decide on which belt or routing to go with? What did you find out. At the end of the video you show both ways to route the belt.
Either or is neither wrong or right. It’s whichever you decide you like best really. I’ll likely be going with the other option to have a shorter belt. But it would work just the same either way!
more wrap on the pulleys is always better so im going to set mine up like you have it and try that. thanks for making the video. @@mylifesucks327
hello what oil pan and engine mounts are you using I have a 1966 impala I'm trying to LS swap
BRP Hot Rods swap kit and the oil pan is a amazon knock off of a holley 302-1 pan.
What year is the power steering pump? I’m having nothing but issues with my bracket set up cant get the pulley to line up with the crank pulley
As far as I know it’s a 2006 engine. That’s just going off what the junkyard told me when I had it delivered to my house. That and the engine was originally a drive by wire set up. But I don’t know of the power steering being any different throughout those years. Is the water pump aligning with the crank pulley when using the spacers?
Water pump lines up perfect with the crank pulley just not the power steering
@@jasoncroft4822 is the pulley further out than the crank or further in towards the engine?
What size belt is that
Is your alternator going to clear the hood?
I did have to do some trimming on the hood for it to clear but nothing too crazy
How thick are the water pump spacers
I thiiiink they’re about 3/4 inch
F body alt bracket, f body PS bracket, and an f body crank pulley.... looks WAY cleaner and doesnt have a huge chunk of aluminum on the front of the motor.
Car accessories will always be cleaner. But truck engine swapped projects are much more common, this is just an alternative.
@@mylifesucks327 Oh I know. but the parts are everywhere and in the end will cost about the same.
@@pawpatina that's fair, just depends on watcha want really. Personally like the alternator being on top for easy access. Replaced many more of those than I have steering pumps. Luckily GM made these things like Legos for adults so there's many options
@@mylifesucks327 yea im stuffing my ls6 into a miata on my channel so i know all about it... no kits, only thing i bought was monster miata's cv axles since they are plug and play with a ford 8.8 diff.
What bell size.?
Sorry I don’t know the size, only the part number in the description!
Wasted money on water pump and intake… just use carb you’ll get more hp
Wasted money is subjective. This is the direction I wanted to go with it so it’s worth it to me. More than one way to get it done!
Water pump spacer part number 05/2024 update: ICT Billet 551690-71
Awesome thank you!!