Thanks a lot man ! If anybody around here is trying to fix the bearings of the urbanglide ecross pro, it’s the same only when you have to put back the motor inside the wiring are facing down and not up, otherwise it can’t go fully inside and you can’t close the lid
Brilliant video, much more helpful than I was even hoping for! Just a suggestion though, you may want to add some kind of tag to your video. I've just used the first 15 minutes to show myself exactly how to easily get to absolutely everything I need in order to fix the "E-001" error. You have made it simple to isolate all the correct wires, as well as removing the rear wheel to repair/solder any breaks that could be causing that exact fault. There aren't many videos that have helped with that fault (and on the exact scooter I was looking for). The ones I found were mostly non-english so I had no idea what was being said. If you were to add a tag for the E-001 code you might help even more people :)
Thanks for the comment mate. I'll take the advice onboard . Error 001 on a tf-100 LCD display most of the time means hall sensor failure there are a few rare exceptions but mostly hall sensor . If your ever stuck feel free to send me a message an I'll talk u through any scooter/ebike issue's
Hi, Do you know if it is the same size of bearings for the front wheel too please?......ideally I want to strip and replace them straight away rather than finding out what size they are and then have to order them. Thank you.
Nice vid. How much will you charge me to sort my scooter out. I've got a kugoo m4 and i popped the back innertube. I've been through about 5 tubes and they all pop. I ordered a solid back tyre for it but it doesn't fit even though it says its for m4. its doing my head in tbh lol taking the wheel off and putting it ack together for it to pop i think it may need a re wire because taking the wheel off all the time rips the wire casing. it still works fine but not really ridable with a flat tyre.
Hi my kuggoo M4 scooter charges okay but when I start it it cuts outs then won't go again and drains battery saying it's empty when it's just been charged fully ???? Any idea what it can be mate ?????
I have a grinding noise from the back wheel (Motor ?) when I accelerate but the noise goes when I release the accelerator even though the scooter is free wheeling, is there any demos to fix this problem, ?
@@5staranis800 Not yet, The fellow I bought the scooter from no longer answers the phone, im trying to contact kugoo directly, but not having a lot of luck, If I do get to resolve this, I will let you know and I would appreciate it if you do the same, Thanks
Hi mate , damaged motor wire few questions did u rewire it going with a new cable going right through the spindle or was it a cable break that left u enough room to rejoin the too half's in either case did u check the hall sensors are still functioning, chances are if u had a cable break and the scooter was powered up one of the three phase wires touched a hall sensor line and passed more than the 5volts the sensors can handle . Sounds bad but it's not and if u manged to Solder the cable back together I don't see no reason u couldn't swap out the sensors your self if u felt up to it
Hello matte I got I problem to find one motor for my escooter, its a kerin m4 pro 500w .. can you recommend some place to buy one ? Regards Márcio Abreu
IV had a tyre change now IV got error 1 and my scooter doesn't work the wheel spins when off the ground but makes a loud rubbing noise and when I try ride it it's cuts itself out
Hi mate I replaced my tyre tube and now I've got a error code 0001 a motor error but so it doesn't spin at all but when I switch of lights horn etc the motor starts to work but I just vibrates but when I put the scooter on ground it just vibrates
IV got the exact same problem. My wheel does spin when not in the ground but with a loud rubbing noise . If I try to ride it it just cuts out. Error code 1 aswell
@@5staranis800 no idea mate IV looked everywhere online and there not a thing that can help. I'm taking my rear wheel to bits tonight cos that seams to be my only option. I'll let you know if I can find the problem
Mate don’t get offended but it sounds like your from Cardiff I my kugoo playing up got a motor error and I’m from Cardiff any chance of looking at it please
Hi Mike hear ,thank you for your reply, I've got a kugoo M4 I have tried checking all CONNECTORS for loose pins and checked halls in hub and still at a lose
@@mikecathrew9658 hi error 6 on a m4 relates to a communication error between the lcd and the contoller its most likely one of to things a break in the wire loom or the wire loom Junction point at the head it has a known issue . Do u have a multi meter by any chance and I could show u how to find the fault
Thanks a lot man ! If anybody around here is trying to fix the bearings of the urbanglide ecross pro, it’s the same only when you have to put back the motor inside the wiring are facing down and not up, otherwise it can’t go fully inside and you can’t close the lid
Brilliant video, much more helpful than I was even hoping for! Just a suggestion though, you may want to add some kind of tag to your video. I've just used the first 15 minutes to show myself exactly how to easily get to absolutely everything I need in order to fix the "E-001" error. You have made it simple to isolate all the correct wires, as well as removing the rear wheel to repair/solder any breaks that could be causing that exact fault. There aren't many videos that have helped with that fault (and on the exact scooter I was looking for). The ones I found were mostly non-english so I had no idea what was being said. If you were to add a tag for the E-001 code you might help even more people :)
Thanks for the comment mate. I'll take the advice onboard . Error 001 on a tf-100 LCD display most of the time means hall sensor failure there are a few rare exceptions but mostly hall sensor . If your ever stuck feel free to send me a message an I'll talk u through any scooter/ebike issue's
Hi, Do you know if it is the same size of bearings for the front wheel too please?......ideally I want to strip and replace them straight away rather than finding out what size they are and then have to order them. Thank you.
Nice vid. How much will you charge me to sort my scooter out. I've got a kugoo m4 and i popped the back innertube. I've been through about 5 tubes and they all pop. I ordered a solid back tyre for it but it doesn't fit even though it says its for m4. its doing my head in tbh lol taking the wheel off and putting it ack together for it to pop i think it may need a re wire because taking the wheel off all the time rips the wire casing. it still works fine but not really ridable with a flat tyre.
Do you have to open the battery screws to get to the wires
Hi what size are the rear bearings and are they the same size as the front?
Hi my kuggoo M4 scooter charges okay but when I start it it cuts outs then won't go again and drains battery saying it's empty when it's just been charged fully ???? Any idea what it can be mate ?????
Hi mate thanks for the comment ,yes unfortunately sounds like your battery is out of balance or damaged
I have a grinding noise from the back wheel (Motor ?) when I accelerate but the noise goes when I release the accelerator even though the scooter is free wheeling, is there any demos to fix this problem, ?
Ive got the same issue have you sorted it
@@5staranis800 Not yet, The fellow I bought the scooter from no longer answers the phone, im trying to contact kugoo directly, but not having a lot of luck, If I do get to resolve this, I will let you know and I would appreciate it if you do the same, Thanks
Can you put that motor on a g2max front wheel ?
This looks so hard Mate
What would you do if u damaged the wire's,I have soldered back together but it still doesn't work???????
Hi mate , damaged motor wire few questions did u rewire it going with a new cable going right through the spindle or was it a cable break that left u enough room to rejoin the too half's in either case did u check the hall sensors are still functioning, chances are if u had a cable break and the scooter was powered up one of the three phase wires touched a hall sensor line and passed more than the 5volts the sensors can handle . Sounds bad but it's not and if u manged to Solder the cable back together I don't see no reason u couldn't swap out the sensors your self if u felt up to it
Hello matte I got I problem to find one motor for my escooter, its a kerin m4 pro 500w .. can you recommend some place to buy one ?
Regards Márcio Abreu
R u gonna show us the M4 doing 35mph with the speed mod?
Hi there I really need to no something!
What amp fuse can I put in a plug to charge my kugoo m4 kirwin?
Yesterday my engine completely stopped working.and I step on the gas but nothing happens.😭 what do you think happened.❓❔❓
IV had a tyre change now IV got error 1 and my scooter doesn't work the wheel spins when off the ground but makes a loud rubbing noise and when I try ride it it's cuts itself out
I've got the same issue have you fixed it
You can grease the motor? (the magnets) Is that a good ideal? wont it cause any harm to the motor?
There is no friction between them it's a brushless motor absolutely not
Hi i keep getting e006 and e005 error any ideas please
Hey I was wondering where you get your tyres from
Amazon
Nice Intuitive Video's Bud, nice rear shocks, where & how much? I'll get back to you about the lighting kit's & foot plate designs, cheers
Hi mate I replaced my tyre tube and now I've got a error code 0001 a motor error but so it doesn't spin at all but when I switch of lights horn etc the motor starts to work but I just vibrates but when I put the scooter on ground it just vibrates
IV got the exact same problem. My wheel does spin when not in the ground but with a loud rubbing noise . If I try to ride it it just cuts out. Error code 1 aswell
@@lornadavis6663 that's exactly what's happening to me too let me know if you fix it pal
@@5staranis800 no idea mate IV looked everywhere online and there not a thing that can help. I'm taking my rear wheel to bits tonight cos that seams to be my only option. I'll let you know if I can find the problem
@@lornadavis6663 me to please I got the same 😂
Can u do same video but for kugoo G2 pro
I shall when I have one come in, however none in at the mo
Mate don’t get offended but it sounds like your from Cardiff I my kugoo playing up got a motor error and I’m from Cardiff any chance of looking at it please
Sorry just seen your comment , if u still need it repaired just let me no
Wait there is a tubeless for m4 Pro
My KugooKirin G3 has becomebe locked down, How can I reset the speed?
Hi so to do this it would be in the P setting.. If you'd like to get in touch and send me a screenshot ext then I'm happy to walk you through it
@@alphamods6791 Thanks, I've fixed it.
Where did you get tiers from please
Amazon mate 10x3 tubeless tyres but they also can be used with a 10.25 inner tube that is supplied as well with each tyre 19.99 each
Is it a good idea to lubricate the magnets in the motor?
Are you serious 😐
The wire on my back wheel has been damaged and I don’t know what to do only had it a month
I done the same thing gonna attempt a repair on the weekend
@@roya1er210 did it workout and how hard was it
It works lost a few mph off my top speed for some reason but its very findly but its possible
How can i get in contact with you, i have a few questions if you dont mind
Alphaoneprint@gmail.com
hello I am contacting you for help wiring controller for the kugoo m4
Sure no problem
Need help with Erre coad 6
Hi thanks for the comment, what scooter model do u have
Hi Mike hear ,thank you for your reply, I've got a kugoo M4 I have tried checking all CONNECTORS for loose pins and checked halls in hub and still at a lose
@@mikecathrew9658 hi error 6 on a m4 relates to a communication error between the lcd and the contoller its most likely one of to things a break in the wire loom or the wire loom Junction point at the head it has a known issue . Do u have a multi meter by any chance and I could show u how to find the fault
@@alphamods6791 yes I have a multimeter if you pont me in the right direction I am shuar
I can do it
You damaged your new bearing by taping it with hammer..