How to Replace Serpentine Belt Tensioner 2008-12 Chevy Malibu
HTML-код
- Опубликовано: 23 авг 2024
- Buy Now!
New Accessory Drive Belt Tensioner from 1AAuto.com 1aau.to/ia/1AEB...
The tensioner is a springed device that keeps the serpentine belt in your vehicle at the correct tension to keep it on the pulleys, without being so tight that it breaks. Eventually the tensioner may become worn, loose, or stuck, resulting in belts that squeak, slip, or fall off. This video shows you how to install a new TRQ tensioner pulley in your 2008-2012 Chevy Malibu.
• Check here for more videos on the 2008-12 Chevy Malibu: • Chevy Malibu 2008-2012...
This process should be similar on the following vehicles:
2004 Chevrolet Malibu
2005 Chevrolet Malibu
2006 Chevrolet Malibu
2007 Chevrolet Malibu
2008 Chevrolet Malibu
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oqy/1AX...
• Pocket Screwdriver
• 15mm Wrench 1aau.to/oer/1AX...
• 18mm Wrench
• 10mm Socket 1aau.to/onU/1AX...
• 13mm Socket 1aau.to/oqD/1AX...
• 15mm Socket 1aau.to/oqD/1AX...
• 18mm Socket 1aau.to/ohm/1AX...
• 8mm Socket 1aau.to/onU/1AX...
• Serpentine Belt Tensioner Tool 1aau.to/oE/1AXA...
• Ratchet 1aau.to/orU/1AX...
• Socket Driver
• Socket Extensions 1aau.to/oqD/1AX...
• Swivel
• Torque Wrench 1aau.to/oj3/1AX...
• Floor Jack 1aau.to/oeY/1AX...
• Jack Stands 1aau.to/oeF/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Chevy Malibu 2008-2012 7th Generation: • Chevy Malibu 2008-2012...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Pinky 6 video free horses making love
Just did this job yesterday on my son's 2009 Chevy Malibu. Took me about an hour, had to get a new replacement motor mount otherwise about a 30 minutes job if you're in no hurry. I did not remove the motor mount bracket from the engine. I was able to get the belt tensioner off and out with very minimal clearance, just wiggle it a bit and out it comes. Removing the motor mount bracket would make it easier to locate the location when putting in the new one but I managed to get it in there. Now after replacing the tensioner and motor mount his car starts up and runs so much quieter. 164,000 miles, leaks a little oil but it gets him to school and work.
This video is doing it the hard way it's much easier to remove the splash shield and do it from underneath you do not need to remove any engine mounts or the air filter box. Just remove the splash shield from the bottom and you can reach it just fine I've done it on a few
No it is not!!
Yes it is
You dont have to remove the engine mount retainer from the engine block at 2:10 the pulley will squeeze out (I just completed this replacement today). Make sure you dont drop the tensioner bolt into the air box intake or you will have to remove the front bumper like I did....SO fill that in with rags prior to starting this job
I assume it's the same deal for a 2011 Buick Regal? Same motor.
i love how the guy says vehircle
no, seriously though great video
somewhat universal for most ecotecs btw
Works on 2009 pontiac g6. Might be easier to take off tire?I did mine this way and it was pretty easy.I think you might get by just removing the motor mount but not the block bracket.It was only 4 bolts so I removed it any way. Thanks it was a great help.
Great video I did this earlier and the tensioner bolt gets snug but starts spinning again I can't even torque it get loose again. Can someone please help me on what I have to do?
Very Good Demo.
How can I lift the engine on a 2013 ?
The oil pan and exhaust are the only areas I see where I could put a jack
Thank you.
+SJ M8 Thanks for watching our video! 1aau.to/m/Shop-TRQ
Will this be same on Hybrid?
What size bolts are the four mounting bolts??
On Chevy or Malibu the engine block mount bolts are torque yield. You can't use the same bolt again!!
How many miles does the tensioner last
Your electric torque it's awesome ... it's funny you just put it n done... Wait a minute you kinda look like the guy from A1? .. comparing from regular torque wrenches ..
I just got my mechanic butt whooped by a "2013 Chevy Malibu" serpentine belt tensioner ....😠 Can you please do a video on that specific tensioner its a Total mechanic Problem 💯‼ email video or contact me when yall post it 2013 Chevy Malibu Eco
Is this video the same for 3.6 v6?
+Jose A This will be slighly different, here's the how-to video you're looking for: ruclips.net/video/2CclDz1k81Q/видео.html
how about a 2011 regal turbo 2.0? thx in advance for any input. awesome video
@@348frank348 this video is a good idea for the basic gist of it. In case you haven't gotten yours yet I just did my 11 regal turbo and it really only took an hour tops being methodical and adjusting a few of the steps from this video.
What engine is this for smh I hate TRQ
You do not have to take all that off
+Tony Mayweathers We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair. 1aau.to/m/Shop-TRQ
Que num. De parte es la banda y tiene que ser de 7 hilos dónde la consigo
😅😅😮