@@mazatroltipsandtricks6816 no thank you .. your video just made me more money per hour cuz I couldn’t remember how to use mazitrol I can g code and Fanuc manual guide I soo thank you
Sir please make video same like this but please make in metric mode mm you are really great you explain very well you have very good knowledge please it's my request to you please make videos in mm mode sir I watch your every single video please iam waiting for your response thanks a lot sir and hatss off to you
I'm sorry but changing a Mazak to metric mode is not the same as a Fanuc. You have to change a lot of machine parameters to do that. This machine was setup by Mazak from the factory as Imperial inches.
@@mazatroltipsandtricks6816 sir thank you but please explain in your own words make your own drawing on radius , turning,and threading and grooving just to know how to program in mazak smooth because I need your help sir iam getting very difficulties while making a program iam from India sir please help me it's my humble request to you sir
Your video's have helped me greatly I have a t32-2 qt 15 and have never run a cnc lathe before and with your help it's been awesome . I did find some stuff useful on my own that may help others with a limited 3 phase power supply, one is adjust machine parameters on the sp19 from 300 to 2500 as then it won't over voltage I run mine off only 40 amps with my phase technologies 10 hp converter . And as for the tool eye the B63 parameter just keep on adjusting until it cuts to what you program the machine for . I do have a question though as my machine doesn't have the EIA option or it's not turned on do you know how to add it ? Thanks again for your great videos .
Sir. Please help me understand how to find the centre point for a part that starts on Z13(mm) and ends at 33.1(mm) The outside diameter is 168.83 and the radius is 35. I have tried using the centre points 98.83(168.83 - 70(R35x2) and the centre on Z 23.05. The radius does not fully form!
Great presentation, but the designer won't give that kind of drawing to the floor..where in the SPT -Z and FPT-Z of the R.125 is not visible on the drawing, so the Qc will be having a hard time in checking part.
my method is always the same move the g54 outside the piece so you can work "air" do the finishing pass with the "wrong" utensil (rough pass) and write the "x" points, based on max turning pass that utensil can do then you have already the coordinate for rough the piece yes im in the wrong place since is auto-programming on mazatrol but i think this type of programming is too difficult and "slow" compared to normal programming on screen ^^
Hi Phil thank you for your time could you please make a program how to plunch into the inside diameter with a boring bar please? (Like nice taper then straight cut with a radius) if it make sense...
This was just a practice part. Many times a CAD drawing will just show the location of the center of the radius but not the end points. I was trying to use a common example.
@@mazatroltipsandtricks6816 if you know how to work out that formula with out a drawing package of the (4.00) please share it will be helpful as most drawings is very limited on details...
My machine was made in Japan back in 1986. This machine does not have a traditional turret. It has 16 tools all of which can be either static tools or live tools or a mix of both. This machine is the predecessor to the Integrex. Achilles heel is the tool changer does not like stringy chips. They will get wrapped up behind the tools and cause issues.
I have not seem that thanks, new to your channel, I’m doing some hex parts in a couple days only difference it’s on a smooth controller should be similar
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Training on Mazatrol Matrix and Matrix 2. Your videos are helping me learn the language. Thanks
Cool. Glad to help.
That literally is the best mazak programming video out good job
Thanks for the compliment!
@@mazatroltipsandtricks6816 no thank you .. your video just made me more money per hour cuz I couldn’t remember how to use mazitrol I can g code and Fanuc manual guide I soo thank you
@@glendenton3193 Sweet!
Thank you sir, you've made a lot of people a lot of money.
You're welcome.
Thank you, sir! You’ve just gained a subscriber.
Awesome! Thank you.
Thanks for the Video, it was very helpful in understanding Auto Calculations
You're welcome.
the first radius becomes slightly pointed in the large radius, there needs to be a radius between the large and the small to become tangential
Sir please make video same like this but please make in metric mode mm you are really great you explain very well you have very good knowledge please it's my request to you please make videos in mm mode sir I watch your every single video please iam waiting for your response thanks a lot sir and hatss off to you
I'm sorry but changing a Mazak to metric mode is not the same as a Fanuc. You have to change a lot of machine parameters to do that. This machine was setup by Mazak from the factory as Imperial inches.
@@mazatroltipsandtricks6816 sir thank you but please explain in your own words make your own drawing on radius , turning,and threading and grooving just to know how to program in mazak smooth because I need your help sir iam getting very difficulties while making a program iam from India sir please help me it's my humble request to you sir
Thank you for all video you are posting ,it's really helpful.can you make a video for tap and mill tap.thank you.
Sure, I can do that. Thanks.
Awesome work thank you so much
Glad it was helpful.
Your video's have helped me greatly I have a t32-2 qt 15 and have never run a cnc lathe before and with your help it's been awesome . I did find some stuff useful on my own that may help others with a limited 3 phase power supply, one is adjust machine parameters on the sp19 from 300 to 2500 as then it won't over voltage I run mine off only 40 amps with my phase technologies 10 hp converter . And as for the tool eye the B63 parameter just keep on adjusting until it cuts to what you program the machine for . I do have a question though as my machine doesn't have the EIA option or it's not turned on do you know how to add it ?
Thanks again for your great videos .
EIA is really not needed. Been running Mazatrol for 24 years and my machine has the EIA function.
Good one much simple then g code programming of same feature
Sir. Please help me understand how to find the centre point for a part that starts on Z13(mm) and ends at 33.1(mm) The outside diameter is 168.83 and the radius is 35. I have tried using the centre points 98.83(168.83 - 70(R35x2) and the centre on Z 23.05. The radius does not fully form!
God bless you
Thanks
Great presentation, but the designer won't give that kind of drawing to the floor..where in the SPT -Z and FPT-Z of the R.125 is not visible on the drawing, so the Qc will be having a hard time in checking part.
my method is always the same
move the g54 outside the piece so you can work "air"
do the finishing pass with the "wrong" utensil (rough pass)
and write the "x" points, based on max turning pass that utensil can do
then you have already the coordinate for rough the piece
yes im in the wrong place since is auto-programming on mazatrol
but i think this type of programming is too difficult and "slow" compared to normal programming on screen ^^
I suggest reducing rapid to 20 percent on the first run off part.
Absolutely a good idea.
Hi Phil thank you for your time could you please make a program how to plunch into the inside diameter with a boring bar please? (Like nice taper then straight cut with a radius) if it make sense...
I did do a video on using a boring bar in another video titled Demo Part 3. Let me know if you want more.
@@mazatroltipsandtricks6816 thank you
Thank you
Thanks so much for the help
You're welcome.
Very useful tricks. Thank you. I have a problem while creating program for some type of profiles . How can i send you the example drawing. Please help
My contact information is listed in the About me tab on my profile. You need to view it from a computer and not a mobile device. Thanks.
Which tool is this dnmg?
VNMG 332
How do u find the center of the arc (4.000 ) is there a formula or get it from a cad software ?
This was just a practice part. Many times a CAD drawing will just show the location of the center of the radius but not the end points. I was trying to use a common example.
@@mazatroltipsandtricks6816 if you know how to work out that formula with out a drawing package of the (4.00) please share it will be helpful as most drawings is very limited on details...
Didn't get the 4 inch dimension center of radious and the right and left explanation of the same .
The 4 inch dimension is the center of the radius as a diameter value. Left and right arrow shows where the radius intersects the line.
@@mazatroltipsandtricks6816 if the radious is 1.25" shouldn't the diameter be 2.5" I'm sorry still a little cloudy for me !!
@@frankalsterful No. The 4 inch dimension is where the center of the 1.25 radius is located in space.
@@mazatroltipsandtricks6816 what's the formula for finding that center?
this is a mazak made in japan?
any issues with it? i hear the turret is not a real lathe turret ?
My machine was made in Japan back in 1986. This machine does not have a traditional turret. It has 16 tools all of which can be either static tools or live tools or a mix of both. This machine is the predecessor to the Integrex. Achilles heel is the tool changer does not like stringy chips. They will get wrapped up behind the tools and cause issues.
@@mazatroltipsandtricks6816 maybe make a video show how to load tools? etc
@@fredrezfield1629 Sounds good.
@@mazatroltipsandtricks6816 hey man do you have tornado milling option on your mazatrol?
@@fredrezfield1629 I wish I did. It's an awesome feature.
Do you have any videos with a 40n? Mazitrol m-86 computer
No, I just have T-3 controls on my two machines.
Mazatrol Tips and Tricks ok was just wondering some stuff is the same it just seems like mine has faster ways to get there
Can you make more video about milling
Sure. Got something in mind? Email me a sketch if you want. I cannot do anything requiring Y axis though.
Please Make Mazak Integrex Program
I do not have an Integrex at home to video.
Could you show how to do a hex with live tooling or or flat parallel to each other?live your videos new to live tooling
Have you seen the hex video I already made or did you want something different?
I have not seem that thanks, new to your channel, I’m doing some hex parts in a couple days only difference it’s on a smooth controller should be similar
Hi... Do this using G42?
Not sure what you mean? I'm not programming it with G-code.
@@mazatroltipsandtricks6816 oic....i thinking you are using G CODE.You this technology easy to understand.Thanks your comment.
Tpc data and breakdown of how it works PLEASE!!!!
My older machine does not have TPC function so I cannot demonstrate how it works.
i got a lot of problem with TPC data and try to learn it ,but it is hard.if you find any video to learn that .please share with me ,thank you.
@@bambiluong9759 Ok, I will do a TPC video. My machine does not have it, but I will go through it the best I can.
@@mazatroltipsandtricks6816 Thank you sir .
@@bambiluong9759 very Simply Brother You try
Hii sir
does this apply to 640 control and matrix too ? ?or are those completely different ?
It should apply to those controllers as well. Mazatrol turning is essentially unchanged since the beginning. It works on the newer Smooth controls.