I took my drive shaft to get balanced at a shop. I had ugly vibrations when i get to 70mph on freeway! I have a 1988 Monte Carlo SS. When i got the shaft back, i intalled it and wow it made a difference. My car runs smooth on freeway and i even hit 100 mph with no issues.
Thank you for sharing this info brother. It was a crazy problem to have. I know it drove you up the wall!!! So glad you got it solved!!!!! This is why the car community it so awesome, we share!!!!! 👍🏿👍🏿
this is something new to me, I noticed that U-joint is not centered at one end if my chevy drive shaft I thought it is unprober installation but what I discvered after you video there was one of end cap is missing the washer and it is Spicer 331 thanks man for sharing this info which helped me to identify the issue I have since a year
Very interesting! I have a bad vibration going on in my 02 Ws6. I didn't even know about these little washer. I will be checking into this. Thank you for the video.
I’m having same dang problem, still chasing it. I also have Spicer U joints… was it missing thrust washer from factory ? Or had it come out when installing unnoticed ? I’ve recently took my whole driveline out and took it to be rebuilt and balanced, got new U joints. After I reinstalled I’ve had this vibration in rear end and I just had to replace gasket and pinion seal (both had started to leak) I’m thinkin this was symptom of vibration not separate problem.
Cool, love this.. hey, I’m not there, but the pinion angle looks odd in the video. I.e. the rear driveshaft entering the rear end looking to be in opposite degree needed for pre-load? The rear just looks like it need adjustment with the awesome looking “adjustable” link? I love the suspension components❤ Yeah, guess that makes the difference for the alignment of the driveshaft, simple thing the thrust washer. Makes the driveshaft rotate without the wobbles off axis. Cool, thanks for-it!
going to go look now. just installed an eatonlocker 3.42 rear end in my s10 and around 45 ish it vibrates real bad. below and above 45 it goes away also might be driveshaft angles
I'm having a tailshaft vibration issue in my 2002 model Holden VY SS Commodore at 40 km/h (25 mph) & it was very bad after I fitted a brand new rubber driveshaft doughnuts or Guibo,it was very bad between 40-60 km/h (25-40 mph) before I replaced the driveshaft centre support bearing & I did press the middle universal joint off to replace the centre bearing because the universal joint yoke had to be removed so that I could remove the centre bearing. It improved greatly after the centre bearing was replaced but if I stay at 40 km/h then it will vibrate & sometimes it won't. I need to check the pilot bearing for wear in the transmissions slip yoke because I believe that the tailshaft isn't lining up centrally so I need to check for play in the bush. The engine that's in the car is a 5.7 litre Chevrolet LS1 V8 & the transmission is a T56 Tremec 6 speed manual,it does have a worn out axle shaft Inner CV joint but I don't think that's the cause of the problem despite the fact I'm going to replace it anyway !
I've been chasing a vibration forever on my 97 LT1 Camaro SS. Wheels balanced, new harmonic balancer, new 3.5" aluminum driveshaft installed. Lowered on strano springs and koni str.t shocks. Wish I could solve it. Mechanics just say driveshaft or flywheel and shrug. I guess I need an adjustable torque arm to verify pinion angle and adjust if its out of whack
If this is seriously my issue, im gonna f*ckin snap lol ive had my rear apart twice, constantly messing with my driveshaft (evern changed it) and did 2 tailshaft bushings. However if it is my issue and I learned that from this video, i will reply on this comment with a thank you lol
Would you have a contact for this driveshaft professional I have a2011 mustang suffering the same problems haven't made a quarter mile pass yet or been able to hook up nitrous plzzz help me lol
Got a 2000 F350, in Europe!!! Recently it was towed because it was parked illegaly (so they claim). I was not present when they towed it. They cut the bolts that attach the shaft to the flange and removed the shaft from the flange. Towed it about 5 miles and hooked up the shaft again using aluminum bolts. 3 weeks later I drove it off their property. After a couple of maneuvers, trying to get out of their tow-yard, as soon as I got on the street, my flange broke! One thing I forgot to say, throughout all this time, my truck was always attached to a 37foot camper which has about 13,000lbs. Anybody knows why that flange broke?
I took my drive shaft to get balanced at a shop. I had ugly vibrations when i get to 70mph on freeway! I have a 1988 Monte Carlo SS. When i got the shaft back, i intalled it and wow it made a difference. My car runs smooth on freeway and i even hit 100 mph with no issues.
Thank you for videoing this. I have replaced several u joints and never noticed the washers. Normally I don't look at the
inside cap. Again thank you.
Thank you for sharing this info brother. It was a crazy problem to have. I know it drove you up the wall!!! So glad you got it solved!!!!! This is why the car community it so awesome, we share!!!!! 👍🏿👍🏿
this is something new to me,
I noticed that U-joint is not centered at one end if my chevy drive shaft
I thought it is unprober installation but what I discvered after you video there was one of end cap is missing the washer and it is Spicer 331
thanks man for sharing this info which helped me to identify the issue I have since a year
Not a problem 👌
Very interesting! I have a bad vibration going on in my 02 Ws6. I didn't even know about these little washer. I will be checking into this. Thank you for the video.
Thanks man. Well i know where to begin now. Had suspicion that im hving vibration in my prop shaft assmbly. Was already considering the whole thing
Brilliant & sharp approach to DYI auto repair. Thank you !!!!
Good info, Fbody owner here, similar issues. I will check it out
How did you not notice the runout on the drive shaft ?
Dont forget your tail housing bushing as well. Good to go
I’m having same dang problem, still chasing it. I also have Spicer U joints… was it missing thrust washer from factory ? Or had it come out when installing unnoticed ?
I’ve recently took my whole driveline out and took it to be rebuilt and balanced, got new U joints. After I reinstalled I’ve had this vibration in rear end and I just had to replace gasket and pinion seal (both had started to leak) I’m thinkin this was symptom of vibration not separate problem.
Cool, love this.. hey, I’m not there, but the pinion angle looks odd in the video. I.e. the rear driveshaft entering the rear end looking to be in opposite degree needed for pre-load? The rear just looks like it need adjustment with the awesome looking “adjustable” link? I love the suspension components❤ Yeah, guess that makes the difference for the alignment of the driveshaft, simple thing the thrust washer. Makes the driveshaft rotate without the wobbles off axis. Cool, thanks for-it!
going to go look now. just installed an eatonlocker 3.42 rear end in my s10 and around 45 ish it vibrates real bad. below and above 45 it goes away also might be driveshaft angles
👍👍👍👍
Thank you.😎
I'm having a tailshaft vibration issue in my 2002 model Holden VY SS Commodore at 40 km/h (25 mph) & it was very bad after I fitted a brand new rubber driveshaft doughnuts or Guibo,it was very bad between 40-60 km/h (25-40 mph) before I replaced the driveshaft centre support bearing & I did press the middle universal joint off to replace the centre bearing because the universal joint yoke had to be removed so that I could remove the centre bearing.
It improved greatly after the centre bearing was replaced but if I stay at 40 km/h then it will vibrate & sometimes it won't.
I need to check the pilot bearing for wear in the transmissions slip yoke because I believe that the tailshaft isn't lining up centrally so I need to check for play in the bush.
The engine that's in the car is a 5.7 litre Chevrolet LS1 V8 & the transmission is a T56 Tremec 6 speed manual,it does have a worn out axle shaft Inner CV joint but I don't think that's the cause of the problem despite the fact I'm going to replace it anyway !
Awesome tech stuff ... thisbis good to know
It sure is. I have a lot more coming.
I've been chasing a vibration forever on my 97 LT1 Camaro SS. Wheels balanced, new harmonic balancer, new 3.5" aluminum driveshaft installed. Lowered on strano springs and koni str.t shocks. Wish I could solve it. Mechanics just say driveshaft or flywheel and shrug. I guess I need an adjustable torque arm to verify pinion angle and adjust if its out of whack
Was the vibration present under load only or with no load too (pedal off / neutral) ?
Always did it until thrust washer was put back in.
Crazy how that tiny thrust washer could cause a vibration. One thing I haven't double checked on my 97 Camaro hmm
Thanks brother! Good info!!
If this is seriously my issue, im gonna f*ckin snap lol ive had my rear apart twice, constantly messing with my driveshaft (evern changed it) and did 2 tailshaft bushings.
However if it is my issue and I learned that from this video, i will reply on this comment with a thank you lol
Would you have a contact for this driveshaft professional I have a2011 mustang suffering the same problems haven't made a quarter mile pass yet or been able to hook up nitrous plzzz help me lol
He said Denny's.
Probably means Denny's Driveshaft Service.
@@hotrodray6802 thank you
Denny's Driveshaft
Mine is the Nitrous version. Stand up company A++ and the go to for high performance and more.
My elco has a issue with vibration like described in video... gonna check this out.
cool
Big Earn McCracken eh?!...🤣🤷🙋
Got a 2000 F350, in Europe!!! Recently it was towed because it was parked illegaly (so they claim). I was not present when they towed it. They cut the bolts that attach the shaft to the flange and removed the shaft from the flange. Towed it about 5 miles and hooked up the shaft again using aluminum bolts. 3 weeks later I drove it off their property. After a couple of maneuvers, trying to get out of their tow-yard, as soon as I got on the street, my flange broke! One thing I forgot to say, throughout all this time, my truck was always attached to a 37foot camper which has about 13,000lbs. Anybody knows why that flange broke?