please my Nasco 2HP remote is messed up.. how can i reset it to correspond to the AC any time i switch to 16C/17C/18C/19C or any, it automatically goes to 31C
solutions: 1. ensure the thermostat is set to 'cool' mode. 2. external wires intact? 3. check if your home fuse is working 4. check wiring or the motor 5. there could be a problem leading to blowing hot air so lower the temp to 16C for 15-20 min, carefully clean the dirt in the evaporator or condenser. Or call Nasco customer service at 020 439 2626 for an AC guy to check it for u. Good luck!
Hello boss I need your help ...my AC cools to a point then it stops and start blowing heat for some time.......then it starts cooling again.....what might be the issue....it's a Haier brand
Hi Abdul, check your gas level. Aircon must not be on for hours on end. The cooling level will go down if the Aircon is poor performing. Check the servicing. Have an installer come to check for you. Thx
Congratulations 🎊 on the installation of your aircondition unite. How much did it cost you both purchasing and installation. Regards Mr.Bright from Bright&Clara's channel
So why my NASCO AC dashboard keep on changing from 16 to 34, 33 to 32, 32 to 29, 29 to 28….. like it keeps on changing whiles the remote control is on 16
Miklin Wave, kindly pls change your remote battery, if you can, maybe the aircon is not installed professionally. So call Nasco customer service to help you. Tx.
@@YorbingNewsMedia the minimum temperature of all 1.5HP and 2.0HP air conditioners in my department are 16 degrees Celsius. But my NASCO 1.5HP air conditioner's minimum temperature is 17 degrees Celsius instead of 16 degrees Celsius and that's problem with the NASCO air conditioners.
please my Nasco 2HP remote is messed up.. how can i reset it to correspond to the AC
any time i switch to 16C/17C/18C/19C or any, it automatically goes to 31C
solutions: 1. ensure the thermostat is set to 'cool' mode. 2. external wires intact? 3. check if your home fuse is working 4. check wiring or the motor 5. there could be a problem leading to blowing hot air so lower the temp to 16C for 15-20 min, carefully clean the dirt in the evaporator or condenser. Or call Nasco customer service at 020 439 2626 for an AC guy to check it for u. Good luck!
Hello boss I need your help ...my AC cools to a point then it stops and start blowing heat for some time.......then it starts cooling again.....what might be the issue....it's a Haier brand
Hi Abdul, check your gas level. Aircon must not be on for hours on end. The cooling level will go down if the Aircon is poor performing. Check the servicing. Have an installer come to check for you. Thx
Congratulations 🎊 on the installation of your aircondition unite. How much did it cost you both purchasing and installation.
Regards
Mr.Bright from Bright&Clara's channel
Hi Mr. Bright, Purchase: 2.0 R410 is 2360gh + t&t 64+stand 70gh+labor 250. Thx!
@@isabelcofie2553 Thanks alot for the feedback, this is a Nasco brand right?
@@BrightandClara Yes, pls. Thx
@@BrightandClara ✨🇬🇭
So why my NASCO AC dashboard keep on changing from 16 to 34, 33 to 32, 32 to 29, 29 to 28….. like it keeps on changing whiles the remote control is on 16
Miklin Wave, kindly pls change your remote battery, if you can, maybe the aircon is not installed professionally. So call Nasco customer service to help you. Tx.
Ok thanks
@@Deyen40 you're welcome...😀
Please what’s the universal code for nasco Ac
Look at the battery compartment or your remote...good luck 🤞
Would like to know why NASCO split 1.5hp air conditioner minimum temperature is 17 degrees Celsius instead of 16 degrees Celsius.
Hi Kirk, sure, its 2.0 so 16C seems coldest from the manufacturer's?
@@YorbingNewsMedia the minimum temperature of all 1.5HP and 2.0HP air conditioners in my department are 16 degrees Celsius.
But my NASCO 1.5HP air conditioner's minimum temperature is 17 degrees Celsius instead of 16 degrees Celsius and that's problem with the NASCO air conditioners.
@@kirknarh9185 Cool, tx for info, much appreciative.
I bought it 6months ago
How do you want use to learn from this or are you just doing the video for viewing sake?
Boi3😂
Hmmmmm
Some comment that the methods r wrong. Let's keep watching!