Your timing on this was a god send. I pulled this from the bluing salts and my heart dropped. Thankfully I have an operational rust blue setup. Thank you 🙏
I'm glad I could help! I knew when researching for this project that if it went as it did, it could potentially help a lot of smith's and DIY guys. Hope your project went well, cheers!
As someone who just bought another lever gun I have to say you did a superb job on that winchester it absolutely is beautiful you know you `restuff keep it up . I`verefinished a few pistols none came out like your rifle congrats.Dennis
Thank you!! I was very blessed with how it turned out! Luckily for me I always find myself wrapped up in the used and abused section, so I've had quite a bit of practice prior to this! Still haven't gottem my hands on a pistol to reblue though! someday soon I'm sure
Just reviewed your video and man it was great! I have a few lever action 30-30 of my own and I had a restoration job done on one and it turned out all full 😢. The bluing was purple and and the rest of my rifle was …..well, lets just say everyone who says they are a gunsmith is not a gunsmith and everyone who says they restore old rifles may be lying.
Thank you for your time to research, do the labor, and video this process! I am especially pleased to see these “modern” 94’s can be refinished without a rattle can! Nice work! Music in the background is fine, btw.
I'm glad I did all of it, and thanks for watching! Honestly I could have been happy with it keeping the vintage brown look. But it's definitely hard to beat a good honest blue! I'll also keep you in mind as far as the music goes. Honestly it really does help keep the reverb down in a stone shop. For now it has to stay until I get a better audio setup. Cheers!
@@BLWRK An unfortunate period of my life caused me to neglect my ‘72 vintage 94 and the receiver and lever got case rot. Such a shame because the barrel, mag tube and most other parts look great still. Even from new (handed down from my grandfather) the receiver never had that deep blue. The treatment never really “burned in” like traditional steel parts. I have renewed plans for this one now!
It's incredible to know that somebody with your expertise found their way here and enjoyed the video, thank you so much!! P.s. I never knew the correct term for the process, which is amazing!! thanks!
Very nice work. I have been bluing knives and guns for years and got to tell you I learned a lot from you in this video. So much I can improve on. Keep up your good work and hope to see more videos.
I use laurel mountain forge browning solution on my flintlock builds. I let mine rust for a week in a humid climate then steel wool leaving the pits, then neutralize with baking soda..I then blue with 44-40 cold blue. Then I use steel wool and motor oil and bring it back some. Makes them look old and worn. I love building guns to look old. Just my preference. Good job on your work there. I have a post 64 in 30-30 and I am redoing the finish on the stock and forearm but I'm happy with the factory bluing. If I come across a lever that is rough, I may do something similar.
Looks excellent, I have a 1980 Model 94 and I've been having a helluva time trying to blue the receiver. Thanks for the video, I'm going to try your method.
I just rust blued my first flintlock barrel with the Laurel Mountain stuff. It came out great. I did the bath in PVC pipe with boiling distilled water from the kitchen.
Looks good. I am always surprised at the different methods used to rust blue. I have blued several using Mark Novak’s method with good result. I wish you would have discussed cleaning prep prior to application of bluing solution, though I believe anyone trying this will look further into it before committing to the process. Thanks for the video.
Absolutely! Mark is Incredible!! So in a previous video I delved deep on prep and application. This particular blend of Rust bluing Solution is called Laurel Mountain Forge barrel brown and degreaser. Degreasing prior to its use, I have found, to be minimally necessary. Obviously applied degreased, but not nearly as involved as the Trademarked "Rust Blue" or other brands with similar compounds which require a much more extensive degreasing methods. Cheers!
For rust bluing I usually end up polishing down to 400 Grit Silicon Carbide. My rust blue solution etches a very fine amount which I can control using 200 proof ethyl alcohol. I card the surface with a .0025" stainless wire brush then boil in distilled water then do another pass. I use a camel's hair brush for application. Nice work on the final product. It has a beautiful satin finish to it. This should last at least 50 to 75 years.
So I've never done a rifle in this coarse of a grit before. Typically I polish to 600, and have had really good results. The next rifle I'm doing I've polished to 2000 grit to see if its's still capable of biting and reflecting the surface finish. My understanding is that the blue finish has as much to do with how fine it etches just as well as the surface finish, so we'll see how it goes. I've heard of mixing ethyl alcohol to the mixture to give a much more shiny finish, but I haven't stumbled on enough definitive information to really try diving into it and testing it. So any information you might be able to provie would definitely be put to good use!
It looks great. I am not sure if i could do it to my 1949 (year) 30-30 given to me by my dad. (now passed) Thanks I enjoyed the video very much with all respect.
Rust bluing is all I know and I love it. I just finished Win 1873. I tried the cold bluing once. I didn't like it. Ok for screws and pins. Give Birchwood Casey's Browning solution a try. Put on hot steel (~275F) and boil in rain or distilled water...nice deep black.
Amazing outcome!!! Your patience definitely paid off beautifully!!!! I have a post 94 I’m just going to ceracoat it. Done it many times with various firearms with great results but that blue you pulled off is 👌🏻
Thank you so much! I too love the turnout of Cerakote, and honestly it would have probably been far more practical on an instance such as this. BUT, sometimes you just have to try and push the envelope and accommodate the group that loves that old timey feel 😎
I also have one of these nasty 94’s and have been debating the slow rust blue. I can cerakote it so much easier, but that blue finish sure is beautiful. One thing I’m pondering is how would it work if you were to prep the rifle and parts like you would for cerakote and blast it with 120 grit AO instead of sanding it. Degrease and gas out would be the same, but instead of painting, heat it up in the oven and apply a blueing or browning solution. Then card, heat, apply solution, bake and repeat.
Great results and a great video! I've been debating whether to Rust Blue my Winchester Model 12, 16 gauge made in 1932...Now I think I will do it. I'll try for that Winchester dark luster which will require finer surface preparation and many more rust/carding cycles. I'll let you know how it turns out! Thanks again Amigo
Great stuff Adam, excellent demonstration of what can be achieved AND entertaining to boot!……your persona and creative editing make for a winning combination - you’ll go far! Keep up the great work. p.s. one sweet ‘94 result 👍🏻
Thanks! I definitely try to put a lot of heart and soul into my editing. Your comment really reaches deep, and you don't know how much I appreciate all of it!
Dude, OUTSTANDING video. Entertaining and enlightening. Just got my bluing (boiling) tank and carding wheel in the mail. I've got a half dozen old bolt guns that need some TLC and will be rust bluing them soon. Just need to decide on what solution to use. Leaning toward Rust Blue American Formula.
I've used multiple different flavors of the RUST BLUE brand with great results. With said formulae, I've found that prep is incredibly crucial. I do hope the best for your projects, and expect it to be very rewarding!
I did one of these a couple years ago. I removed the barrel and plugged it with dowels to protect the bore. I boiled and carded after each time in the humidifier. Turned out great.
Was going to mention Mark Novak's steam chamber (hot plate/stockpot/PVC tower with cap) setup then saw a mention of him with your awareness. Busted my bubble😅. Surprised you didn't have some rod across your boil tank to suspend the smaller parts. The firearm turned out great 👍.
It is important that you let people know the central importance of 150% degreasing before applying the rusting solution. I just finished the second application of bluing to a No 4 MK I, and I never card off the frog hair after first applying the rusting agent and it turns out the same. Also, I use a makeshift accelerated 'ripening' chamber I cobbled together out of a U-haul wardrobe moving box, a small space heater, and a Walgreens vaporizer to bring the heat above dewpoint (110% necessary if using low pressure steam, as condensation on the metal will cause runs) and about 100% humidity. It works a lot faster than 3-4 hours. Great save though!
Very good job, makes me appreciate the bluing job my dad did on my 1965 marlin model 60 back in 1979 after I forgot it outside in the rain when my wife was in labor with our daughter. 🙂 I am the way the truth and the life, no one comes to the Father but by Me. Jesus Christ
Long story short, WOW! I have a post 1964 model 94 in need of refinishing - Still serviceable and in use though needing refinishing, but I have nowhere near the patience and skill that you exhibit.
Thank you from all of us who have bought that $25 .22 rifle that is perfectly fine except for the purple and yellow spots that Bubba left when he baptized it in a bottle of touch-up blue.
The Alloy would absolutely be the same, but the outer finish is what is determined by the year of MFG, or more precisely the Serial Number will determine the finish. You will still absolutely be able to use this technique, but it may just take some extra sanding to get to the bare Sintered Metal. Cheers!
That was a lot of hard work but in the end it certainly was worth it. Came out great. Does anyone know when they stopped iron plating the receivers? I think I have heard that it was before 1970 but I was just wondering. No way I would ever want to do that much work on a gun and I could only imagine what it would cost to have that done.
I have a .44 Magnum model 94 with the crappy peeling blue. Brought it to a local gun shop that does gunsmith work. The guy said you can’t blue it and wanted to $175 to durablue the receiver. The barrel was actually in good condition. I believe Winchester went back to a hot blue in the early 80’s. Maybe I will find someone who can do this type of work.
I have never used an air brush, but I will definitely look into it! I've read a little bit about chemical mist bluing, but I've been so consumed lately with this that it fell on blind eyes. I'll definitely look into it more, stay tuned!
Oh man... that looks absolutely gorgeous. Makes mine look like a turd. I'm still debating on how to refurb mine and I don't have the room nor the equipment you have, so I'm probably gonna have to rely on hot salts or cold bluing. Yeah, I know. Cold bluing is more cosmetic painting rather than actual bluing. Might look into that vegetable oil quenching, see how that holds up.
Honestly, if it were me in your shoes, I would look into durakote or Brownells equivalent Alumahide. Both work incredibly well, and I've seen many with the right prep, turn out great! Just my $.02, goodluck!
@@BLWRK Wow, I'm actually quite interested in that Duracoat. I've been checking their website out for the past few minutes and they seem legit. I'll check out the Brownells stuff as well, but yeah, I'm leaning towards the former! Thanks for the suggestion!
i was gunsmithing in virginia back in the late 80,s and tried everything to blue one was doing some stainless parts in stainless blueing solution and figuered id try the reciever in that ,,came out really black till i tried to whip it down with oil all and i mean all of the blackness came off in my hands total failure cant remember what else i did to it
Not necessarily. In the past, I used to boil and card between every cycle. After about my 12th rifle, I began carding after every rust cycle. Cutting out the boiling step altogether until I get a nice velvet brown. I have found that the end results are virtually indistinguishable.
Hey nice video ! Can I replace the rust bluing solution product by a bluing product such as aluminum black or Perma Blue from Birchwood Casey and do the exact same process ?
If you were looking for a bluing finish, this is the most practical way to do it. Being that yours is an early serial number chrome finished rifle, you will have a bit more sanding to do on the receiver to remove the plated layers, but after that, the process would be identical! Typically refinishing these consist of all the kotes(cerakote, gunkote, durakote, etc) rust bluing is an option(matte to gloss) or, you could send it out to be iron plated then hot blued. I've listed these in the order of practicality.
I'm a firm believer in keeping all tools, especially firearms, in good working condition. However, one must absolutely weigh the consequences of their actions and decide accordingly. In other words, if the gun is in absolutely horrid condition with no chance of survival without intervention.. then it's a no Brainer. BUT, if it's a personal preference decision based on how it looks, you must consider that it will probably lower the value of the gun to collectors. Food for thought, cheers!
In 1964 Winchester did not make the decision, the new owners, Olin Corp. did. Cost cutting just like AMF did when they bought out Harley Davidson back in the day.
i think the pre 64 winchester 94 is the most beautiful rifle ever made. And yours came out stunning.
Thank you!
This by far the most underrated gun Chanel I’ve come across. Gonna be showing all my gun buddies
Probably the best video so far, gun turned out beautiful
Thanks bruv, I'm really really happy with how this turned out! Now I can officially quit youtube happy hahaha
Not too bad for a rookie! Very nice! Oh, and the music is just fine
Your timing on this was a god send. I pulled this from the bluing salts and my heart dropped.
Thankfully I have an operational rust blue setup. Thank you 🙏
I'm glad I could help! I knew when researching for this project that if it went as it did, it could potentially help a lot of smith's and DIY guys. Hope your project went well, cheers!
As someone who just bought another lever gun I have to say you did a superb job on that winchester it absolutely is beautiful you know you `restuff keep it up . I`verefinished a few pistols none came out like your rifle congrats.Dennis
Thank you!! I was very blessed with how it turned out! Luckily for me I always find myself wrapped up in the used and abused section, so I've had quite a bit of practice prior to this! Still haven't gottem my hands on a pistol to reblue though! someday soon I'm sure
Patients is a vertue and your gun is a result. Your education was well worth the time. Thank you.
You are one of the reasons I love RUclips.
Me too
Just reviewed your video and man it was great! I have a few lever action 30-30 of my own and I had a restoration job done on one and it turned out all full 😢. The bluing was purple and and the rest of my rifle was …..well, lets just say everyone who says they are a gunsmith is not a gunsmith and everyone who says they restore old rifles may be lying.
What a great finish on a great gun. I love your enthusiasm and so glad to have discovered this channel!
Thanks!! I'm glad you made it here! Lots more to come very soon!
I genuinely appreciate this video. You put a lot of effort into filming it. Super straightforward and simple. Thanks
Thank you for your time to research, do the labor, and video this process! I am especially pleased to see these “modern” 94’s can be refinished without a rattle can! Nice work!
Music in the background is fine, btw.
I'm glad I did all of it, and thanks for watching! Honestly I could have been happy with it keeping the vintage brown look. But it's definitely hard to beat a good honest blue!
I'll also keep you in mind as far as the music goes. Honestly it really does help keep the reverb down in a stone shop. For now it has to stay until I get a better audio setup.
Cheers!
@@BLWRK An unfortunate period of my life caused me to neglect my ‘72 vintage 94 and the receiver and lever got case rot. Such a shame because the barrel, mag tube and most other parts look great still.
Even from new (handed down from my grandfather) the receiver never had that deep blue. The treatment never really “burned in” like traditional steel parts. I have renewed plans for this one now!
I would say "You Nailed IT" as a guy who did OJT Industrial Passivation and rust bluing is a passivation, Great Looking Job!.
It's incredible to know that somebody with your expertise found their way here and enjoyed the video, thank you so much!!
P.s. I never knew the correct term for the process, which is amazing!! thanks!
@@BLWRK and "I AM" Saved! I trust you too!
That is beautiful results. Best looking post 64 I ever seen.
Positive, handsome with superb result!)))
Thank you very much!
Very nice work. I have been bluing knives and guns for years and got to tell you I learned a lot from you in this video. So much I can improve on. Keep up your good work and hope to see more videos.
I use laurel mountain forge browning solution on my flintlock builds.
I let mine rust for a week in a humid climate then steel wool leaving the pits, then neutralize with baking soda..I then blue with 44-40 cold blue. Then I use steel wool and motor oil and bring it back some. Makes them look old and worn. I love building guns to look old. Just my preference.
Good job on your work there. I have a post 64 in 30-30 and I am redoing the finish on the stock and forearm but I'm happy with the factory bluing. If I come across a lever that is rough, I may do something similar.
Awesome job! Looks outstanding!!
Looks excellent, I have a 1980 Model 94 and I've been having a helluva time trying to blue the receiver. Thanks for the video, I'm going to try your method.
I just rust blued my first flintlock barrel with the Laurel Mountain stuff. It came out great. I did the bath in PVC pipe with boiling distilled water from the kitchen.
That's great! The chemical reaction does not care what avenue it takes! Cheers
Great job. That came out looking really, really nice. Thanks for sharing your process.
Thanks so much! It is my pleasure!
Looks good. I am always surprised at the different methods used to rust blue. I have blued several using Mark Novak’s method with good result. I wish you would have discussed cleaning prep prior to application of bluing solution, though I believe anyone trying this will look further into it before committing to the process. Thanks for the video.
Absolutely! Mark is Incredible!!
So in a previous video I delved deep on prep and application. This particular blend of Rust bluing Solution is called Laurel Mountain Forge barrel brown and degreaser. Degreasing prior to its use, I have found, to be minimally necessary. Obviously applied degreased, but not nearly as involved as the Trademarked "Rust Blue" or other brands with similar compounds which require a much more extensive degreasing methods.
Cheers!
For rust bluing I usually end up polishing down to 400 Grit Silicon Carbide. My rust blue solution etches a very fine amount which I can control using 200 proof ethyl alcohol. I card the surface with a .0025" stainless wire brush then boil in distilled water then do another pass. I use a camel's hair brush for application.
Nice work on the final product. It has a beautiful satin finish to it. This should last at least 50 to 75 years.
So I've never done a rifle in this coarse of a grit before. Typically I polish to 600, and have had really good results. The next rifle I'm doing I've polished to 2000 grit to see if its's still capable of biting and reflecting the surface finish. My understanding is that the blue finish has as much to do with how fine it etches just as well as the surface finish, so we'll see how it goes.
I've heard of mixing ethyl alcohol to the mixture to give a much more shiny finish, but I haven't stumbled on enough definitive information to really try diving into it and testing it. So any information you might be able to provie would definitely be put to good use!
It looks great. I am not sure if i could do it to my 1949 (year) 30-30 given to me by my dad. (now passed) Thanks I enjoyed the video very much with all respect.
I don't blame you! I'm sure it's a beautiful piece in its own right with more character than either of us! Glad you enjoyed!
i am about to do my 1889 marlin the same way,your gun came out wonderfull!!!
Rust bluing is all I know and I love it. I just finished Win 1873. I tried the cold bluing once. I didn't like it. Ok for screws and pins. Give Birchwood Casey's Browning solution a try. Put on hot steel (~275F) and boil in rain or distilled water...nice deep black.
Amazing outcome!!! Your patience definitely paid off beautifully!!!! I have a post 94 I’m just going to ceracoat it. Done it many times with various firearms with great results but that blue you pulled off is 👌🏻
Thank you so much! I too love the turnout of Cerakote, and honestly it would have probably been far more practical on an instance such as this.
BUT, sometimes you just have to try and push the envelope and accommodate the group that loves that old timey feel 😎
I also have one of these nasty 94’s and have been debating the slow rust blue. I can cerakote it so much easier, but that blue finish sure is beautiful.
One thing I’m pondering is how would it work if you were to prep the rifle and parts like you would for cerakote and blast it with 120 grit AO instead of sanding it. Degrease and gas out would be the same, but instead of painting, heat it up in the oven and apply a blueing or browning solution. Then card, heat, apply solution, bake and repeat.
Bluing Winchester mystery metal…you did it…fabulous job…subbed.
Great results and a great video! I've been debating whether to Rust Blue my Winchester Model 12, 16 gauge made in 1932...Now I think I will do it. I'll try for that Winchester dark luster which will require finer surface preparation and many more rust/carding cycles. I'll let you know how it turns out! Thanks again Amigo
Great job man! Patience and perseverance paid off, and that's a beautiful rifle. Thanks for sharing.
Bravo brother ! What an awesome finish !
Thanks!
Great stuff Adam, excellent demonstration of what can be achieved AND entertaining to boot!……your persona and creative editing make for a winning combination - you’ll go far! Keep up the great work.
p.s. one sweet ‘94 result 👍🏻
Thanks! I definitely try to put a lot of heart and soul into my editing. Your comment really reaches deep, and you don't know how much I appreciate all of it!
Incredible stache! 😌 a satisfactory stache
My freedom caterpillar accepts and appreciates your praise.
'Merica
Very impressive. A long process but the end result is definitely worth it. Cheers
Thanks! Cheers!
Dude, OUTSTANDING video. Entertaining and enlightening. Just got my bluing (boiling) tank and carding wheel in the mail. I've got a half dozen old bolt guns that need some TLC and will be rust bluing them soon. Just need to decide on what solution to use. Leaning toward Rust Blue American Formula.
I've used multiple different flavors of the RUST BLUE brand with great results. With said formulae, I've found that prep is incredibly crucial. I do hope the best for your projects, and expect it to be very rewarding!
I did one of these a couple years ago. I removed the barrel and plugged it with dowels to protect the bore. I boiled and carded after each time in the humidifier. Turned out great.
Wow! That's truly a work of art!
Thank you!
Now this is a true craftsman at work. 👍
Was going to mention Mark Novak's steam chamber (hot plate/stockpot/PVC tower with cap) setup then saw a mention of him with your awareness. Busted my bubble😅.
Surprised you didn't have some rod across your boil tank to suspend the smaller parts.
The firearm turned out great 👍.
I subscribed just because of this video. I absolutely love my Win. 94s. Two chambered in 30-30 and the other in 44 mag.
Glad you enjoyed! I'm pretty fresh at posting so the content will only be getting better!
So when is some new content coming up again? This video showed up on my feed again. Waiting for some more good content!
It is important that you let people know the central importance of 150% degreasing before applying the rusting solution. I just finished the second application of bluing to a No 4 MK I, and I never card off the frog hair after first applying the rusting agent and it turns out the same. Also, I use a makeshift accelerated 'ripening' chamber I cobbled together out of a U-haul wardrobe moving box, a small space heater, and a Walgreens vaporizer to bring the heat above dewpoint (110% necessary if using low pressure steam, as condensation on the metal will cause runs) and about 100% humidity. It works a lot faster than 3-4 hours. Great save though!
Very good job, makes me appreciate the bluing job my dad did on my 1965 marlin model 60 back in 1979 after I forgot it outside in the rain when my wife was in labor with our daughter. 🙂
I am the way the truth and the life, no one comes to the Father but by Me.
Jesus Christ
Long story short, WOW!
I have a post 1964 model 94 in need of refinishing - Still serviceable and in use though needing refinishing, but I have nowhere near the patience and skill that you exhibit.
Great music- excellent video.
Awesome job I've done this before with a Marlin 336 and yours turned out better then mine
Thank you from all of us who have bought that $25 .22 rifle that is perfectly fine except for the purple and yellow spots that Bubba left when he baptized it in a bottle of touch-up blue.
Great job! Art takes time!
Thank you!
Hello
Nice video.
My winchester 3030 was made in 1978. And i wonder if its is the same alloy ?
Thanks.
The Alloy would absolutely be the same, but the outer finish is what is determined by the year of MFG, or more precisely the Serial Number will determine the finish. You will still absolutely be able to use this technique, but it may just take some extra sanding to get to the bare Sintered Metal.
Cheers!
That was a lot of hard work but in the end it certainly was worth it. Came out great. Does anyone know when they stopped iron plating the receivers? I think I have heard that it was before 1970 but I was just wondering. No way I would ever want to do that much work on a gun and I could only imagine what it would cost to have that done.
Awesome video! Glad I found your channel!
I have a .44 Magnum model 94 with the crappy peeling blue. Brought it to a local gun shop that does gunsmith work. The guy said you can’t blue it and wanted to $175 to durablue the receiver. The barrel was actually in good condition. I believe Winchester went back to a hot blue in the early 80’s. Maybe I will find someone who can do this type of work.
Beautiful job! I'm more of a Marlin fan but that really is gorgeous!
Ive always used sponge brushes for the best results using cold blueing, nice even coat, no streaking.
Beautiful job!!! Thanks for sharing
Awesome job! Love me a Winchester!!
Very nice work Adam...
Thank you!
Wow! That turned out great!
Thanks! It was a ton on fun, not nearly as much fun as shooting one of these if you know what i mean! :D
You are awesome, you did a great job.
Great job..... Looks awesome!
Thank you
Very nice work Sir!!
That came out very Nice!!
Turned out Supreme Bro,
Good Work
Have you used a airbrush to apply the acid for evenness and no runs lite coats some people will heavy spray
I have never used an air brush, but I will definitely look into it! I've read a little bit about chemical mist bluing, but I've been so consumed lately with this that it fell on blind eyes.
I'll definitely look into it more, stay tuned!
i am saved. it is the most important dicesion one can make.
Oh man... that looks absolutely gorgeous. Makes mine look like a turd. I'm still debating on how to refurb mine and I don't have the room nor the equipment you have, so I'm probably gonna have to rely on hot salts or cold bluing. Yeah, I know. Cold bluing is more cosmetic painting rather than actual bluing. Might look into that vegetable oil quenching, see how that holds up.
Honestly, if it were me in your shoes, I would look into durakote or Brownells equivalent Alumahide. Both work incredibly well, and I've seen many with the right prep, turn out great!
Just my $.02, goodluck!
@@BLWRK Wow, I'm actually quite interested in that Duracoat. I've been checking their website out for the past few minutes and they seem legit. I'll check out the Brownells stuff as well, but yeah, I'm leaning towards the former! Thanks for the suggestion!
Wow, just amazing
Thanks!
i was gunsmithing in virginia back in the late 80,s and tried everything to blue one was doing some stainless parts in stainless blueing solution and figuered id try the reciever in that ,,came out really black till i tried to whip it down with oil all and i mean all of the blackness came off in my hands total failure cant remember what else i did to it
Here before you blow up lol. Insanely underrated channel
Well done!
Good work Adam👍
Aren't you supposed to boil and card after every application and rust cycle?
Not necessarily. In the past, I used to boil and card between every cycle. After about my 12th rifle, I began carding after every rust cycle. Cutting out the boiling step altogether until I get a nice velvet brown. I have found that the end results are virtually indistinguishable.
I've rust blued 7 of them. Iron plated receiver?
Hey nice video !
Can I replace the rust bluing solution product by a bluing product such as aluminum black or Perma Blue from Birchwood Casey and do the exact same process ?
What kind of wire do you use when pulling it out and coating it with laurel mountain
Omg. Super cool. I need this for grandpas Gun. It’s not bad shape but probably never cleaned. little bit of rust pitting. HELP!
Gladly, unless you're looking to take on the task of refinishing it, your best bet is just steel wool, then keep it oiled! Cheers
I had a 1967 Winchester with that black chrome finish on the receiver. Did not care for that but what else could you do?
If you were looking for a bluing finish, this is the most practical way to do it. Being that yours is an early serial number chrome finished rifle, you will have a bit more sanding to do on the receiver to remove the plated layers, but after that, the process would be identical!
Typically refinishing these consist of all the kotes(cerakote, gunkote, durakote, etc) rust bluing is an option(matte to gloss) or, you could send it out to be iron plated then hot blued. I've listed these in the order of practicality.
I have a 1931 built model 94 leave it alone or work on it ?
I'm a firm believer in keeping all tools, especially firearms, in good working condition. However, one must absolutely weigh the consequences of their actions and decide accordingly.
In other words, if the gun is in absolutely horrid condition with no chance of survival without intervention.. then it's a no Brainer. BUT, if it's a personal preference decision based on how it looks, you must consider that it will probably lower the value of the gun to collectors.
Food for thought, cheers!
Thanks , I have a later 94 that needs a refinish .
What rust blue solution did you utilize for this project?
Laurel Mountain Forge barrel brown and degreaser
new subscriber here, enjoyed the video, looking forward to following your channel.
What a great job 😮thank you for your vidéo !!!
Glad you liked it!
Gorgeous. Nice job.
Amazing work!
Did you rust blue the screw heads?
In 1964 Winchester did not make the decision, the new owners, Olin Corp. did.
Cost cutting just like AMF did when they bought out Harley Davidson back in the day.
Did you re-blue the heads of the screws?
Great question that I didn't cover in the video! I flame blue all screws that I either have to repair, or are already in the white!
Cheers!
@@BLWRK Thanks for the clarification.
Also did you do anything to the inside of the barrel or the magazine tube?
Super job!!!
Thank you!
That was Awesome!!!
🤤🤤🤤🤤🤤. I was just saying mine really needs a facelift. I now know exactly how I’m going to do it.
Great job! It looks awesome! You got a new subscriber out of me bro. This may push me to do something with that spare 94 receiver I have. Hmmm
Thanks man! glad you made it!! If you do decide to dive in on that '94 receiver, stop back and let me know how it goes!
I tried that years ago and while it looks good now it will deteriorate very quickly.
Thats good work.
Thank you!
On my todo list!
If you were in canada I would love to get you to do my 16" 44 mag
Thanks 😊
Amazing!
Are you in California by chance?
Excellent!
Many thanks!
Good job !
Thank you!
Where are you located??? Do you do work for customers???
Nice job 1