I had Rx losses and HM asked to turn off the led strip after that the problem went away....however my ceramic antenna broke and my replacement wire antenna broke as well so going to add a receiver per your video.
Nice video! I need to this because I order the Mobula 8 in the PNP version by accident, I was wondering how did you hide the receiver? It looks complicated to fit it in the drone
Thanks for this video. Is the ep2 antenna you linked in the description better than the one that shipped with the Mob 8? It looks pretty much the same as the one on mine. I’ve damaged the antenna on mine so looking for ways to fix it, and your video seems a good option. Would this get a greater range? Thanks
Hey, I also damaged my antenna and looking for a new one, I found one on rs-online, but I don’t know if it’s the right one(Molex SMT-Antenne Bluetooth (BLE), WLAN Leiterplatte 3.7dBi 3 x 3 x 4mm). Im German please excuse my poor English 😅. I’m not sure if it’s the right one because ther are more that look the exact same to me. That would be the Molex SMT-Antenne Chip 3.6dBi 3 x 3 x 4mm. and the Molex 47948 SMT-Antenne Bluetooth (BLE), WLAN Extern 2400 → 2483,5 MHz Chip 3.3dBi 3 x 3 x 4mm. I would be very very thankful if you could help me 🙏
@@weckweck48 I would bother as it is super complicated to resolder the new one, unless you have hot air soldering experience of microscopic things. the antenna you found is correct one.
@@steriospeaker find the ground pad on FC (diagram shows it) and check all four antenna pads with it for continuity, the three pads that have continuity are the ground ones and the fourth that is left and hasn't continuity is the right one. that is how you also want to check if you soldered correctly. I did, but then broke the correct pad as the antenna-wire is always abused and while straightening it, the pad came of the FC with the wire itself.
@@DronePH-2024 thanks for the reply. I mean happymodel has two external RX modules. One with built in antenna EP2 RX (you installed) and one with external antenna EP1 RX. I think it will give even more range.
@@hishamghosheh9613 the problem is that there's nowhere to put that external ELRS antenna. I'm now thinking which receiver to choose as I have broken the stock ceramic antenna, then soldered simple 31 mm wire instead (which had better range comparing to molex/ceramic) and then have broken the wire which it seems came of with the soldering pad of FC.
is this SPI ELRS Mobula? the problem with my UART ELRS Mobula 8 is that I've broken ceramic antenna, then soldered wire antenna which was even better and then while trying to straighten that wire the pad it was soldered came off... I so I've soldered Happymodel EP1 with external antenna, but the problem is that if I switch off UART1 Serial Rx and turn on UART2 Serial Rx -- I do not get video from the VTX, otherwise I can't control quad using the external EP1. it is one or other. here's the answer form Happymodel: "As this vtx and the onboard elrs receiver share the same MCU, so if you only disable the receiver, then the vtx will not working . If the ceramic antenna was broken , you can solder an copper wire to replace . It's very easy . Just solder a 31mm length copper wire to the pad that marked."
I had Rx losses and HM asked to turn off the led strip after that the problem went away....however my ceramic antenna broke and my replacement wire antenna broke as well so going to add a receiver per your video.
@@balajiprasad9046 great brother happy flying 👍
Nice video! I need to this because I order the Mobula 8 in the PNP version by accident, I was wondering how did you hide the receiver? It looks complicated to fit it in the drone
You can hide brother inside the canopy and works great specially on range happy flying brother thanks for watching 👍
@@DronePH-2024 thanks for sharing this super useful content bro 👊
Great upgrade dude i will install also on my mobula 8 thanks for this.
this is the best way brother to fix issues on rx loss thanks for watching👍
Thanks for this video.
Is the ep2 antenna you linked in the description better than the one that shipped with the Mob 8? It looks pretty much the same as the one on mine.
I’ve damaged the antenna on mine so looking for ways to fix it, and your video seems a good option. Would this get a greater range?
Thanks
@@steriospeaker yap brother for me better range hope you to thanks to brother for watching next video upgrade the frame happy flying👍
Hey, I also damaged my antenna and looking for a new one, I found one on rs-online, but I don’t know if it’s the right one(Molex SMT-Antenne Bluetooth (BLE), WLAN Leiterplatte 3.7dBi 3 x 3 x 4mm). Im German please excuse my poor English 😅. I’m not sure if it’s the right one because ther are more that look the exact same to me. That would be the Molex SMT-Antenne Chip 3.6dBi 3 x 3 x 4mm. and the Molex 47948 SMT-Antenne Bluetooth (BLE), WLAN Extern 2400 → 2483,5 MHz Chip 3.3dBi 3 x 3 x 4mm. I would be very very thankful if you could help me 🙏
@@DronePH-2024help please
@@weckweck48 I would bother as it is super complicated to resolder the new one, unless you have hot air soldering experience of microscopic things. the antenna you found is correct one.
I just soldered enameled wire 31mm long to the signal pad of the express lrs on aio
Great bro 👍
I think I need to do this. Did you follow a guide you could link? Which pad is it? Thanks.
@@steriospeaker find the ground pad on FC (diagram shows it) and check all four antenna pads with it for continuity, the three pads that have continuity are the ground ones and the fourth that is left and hasn't continuity is the right one. that is how you also want to check if you soldered correctly. I did, but then broke the correct pad as the antenna-wire is always abused and while straightening it, the pad came of the FC with the wire itself.
hello, installing this antenna will make it possible to fly to a longer distance?
@@Dmytro_lv yap brother better distance i recommended to select Ep1 rx reciever thanks👍
ep1 or ep2?
you recommend to install ep2 in video.
which is better?
Hi sir, what’s the difference between ep1 and ep2 ? And which one is better ?
@@aimanhemran ep1 ang better boss kc my antenna siya na T,ang Ep2 ceramic antenna lang kaya mas mahina
Which the best to buy Mobula8 analog or the Beta Pavo Pico or the Pavo20?
Excluding the DJI 03 air unit.
If you have plan to buy whoop with DJI 03 Better choose Pavo Pico than mobula 8 thanks👍
Salamat sa advise Bossing.
Anong negative sides sa Mobula 8?
Very nice..thanks for sharing😊
Thanks brother appreciated it👍
Nice upgrade🥂
Thanks brother 👍
Why not go for the version with the external antenna for better range?
I already try bro but still better install external Rx for better range upon my experience thanks for watching 👍
@@DronePH-2024 thanks for the reply. I mean happymodel has two external RX modules. One with built in antenna EP2 RX (you installed) and one with external antenna EP1 RX. I think it will give even more range.
I wondered this too. Would the EP1 get better range?
@@steriospeakerI believe so. The external antenna is much better than the tower antenna
@@hishamghosheh9613 the problem is that there's nowhere to put that external ELRS antenna. I'm now thinking which receiver to choose as I have broken the stock ceramic antenna, then soldered simple 31 mm wire instead (which had better range comparing to molex/ceramic) and then have broken the wire which it seems came of with the soldering pad of FC.
I bought UART ELRS, will I have problems?
And I will need to buy this external rx 😢
You can buy external Rx brother for better Range because before I have issues with Rx loss on my built in receiver on my mobula 8 thanks 👍
Thinking about buying Mob8. Should I order extra frames for it, does it break often?
Hard to break brother no need
is this SPI ELRS Mobula? the problem with my UART ELRS Mobula 8 is that I've broken ceramic antenna, then soldered wire antenna which was even better and then while trying to straighten that wire the pad it was soldered came off... I so I've soldered Happymodel EP1 with external antenna, but the problem is that if I switch off UART1 Serial Rx and turn on UART2 Serial Rx -- I do not get video from the VTX, otherwise I can't control quad using the external EP1. it is one or other. here's the answer form Happymodel:
"As this vtx and the onboard elrs receiver share the same MCU, so if you only disable the receiver, then the vtx will not working .
If the ceramic antenna was broken , you can solder an copper wire to replace . It's very easy . Just solder a 31mm length copper wire to the pad that marked."
how do you disable aio vtx? bridge or software?
Just set it on Betaflight brother thanks👍
why do you want to disable AIO VTX after adding external ELRS module?
Good to know thanks for this + 1
Thank you very much appreciated 👍
Frame upgrade suggestion??
@@emmanuelcheveau4891 i think BETAFPV Meteor 85 pro can fit with our mobula 8 video on going next check here for the frame👉bit.ly/BETAFPVDronePH24
@@DronePH-2024 Did you try it ?
@@emmanuelcheveau4891 yes brother only issue is about mounting the motors you can see in my next video soon after my review on Betafpv thanks
@@DronePH-2024 thanks from Montreal Canada :)
Sir may kasama na bang remote yang mobula 8?
Wala pa bossing drone lang my mura Ngayon na remote nasa70usd radio master pocket upload ko sunod ok Siya para sa mobula 8
@@DronePH-2024 sige tignan ko