The Gorilla mMTW board is now available! Check out Mac Airsoft (EU) - www.mac-airsoft.it/hpa/electronics/gorilla/ Airsoft Armourer (UK) - airsoftarmourer.co.uk/product/gorilla-mmtw/ I will add a US store once starts stocking them!
It's def on the list, I am just waiting for the store where I live to import them (stupid German laws). I like that they have gone for a longer barrel on the II, those few extra mm will allow for better fps for those playing outdoors.
Thanks for watching. I will be doing a few more Article 1 videos. I also have some tech videos lined up specifically on the Article 1. Plus a few on the MTW line as a whole.
Yo, the one I have is the mMTW board, currently the only place I know where to get one is directly from Gorilla. Their site is a WIP and should go live soon. However, you can message him directly on instagram (airsoft.gorilla) and he should be able to sort you out with the mMTW board and trigger. Or you can message MAC Speedsoft and ask him about the mMTW. He currently only has the mFCU and mini-FCU listed on his site, but he can definitely organize the mMTW board for you. Gorilla and MAC work very closely together on many projects and just released the QCU (Quick Carbon Upper) together.
Hey, we use joules where I live and always measured with actual BB weight. But technically if I use the conversion chart and .20s as a reference I have gotten it down to under 250fps and as high as 440fps. But to get it to 440fps I had to crank up the dwell and the reg was at 140psi to get it there. I don't think the stock board can even get to that dwell.
Im having issues with my article 1 speedqb when i plug the battery in and pull the trigger it doesnt fire, no click or anything. I think my trigger board is broken
It's more than likely that the screws have been set incorrectly, the pressure on the board changes once you put it back together again. Screw in the activation screw for the microswitch and reassemble the gun to see if it is finally activates when assembled.
@@AirsoftMax-EU I installed the OG spring! But I think it’s solved maybe too much paint on the chamber it was jamming on the barrel nut there is a little paint off but springy now!!! And when comes that Gorilla FCU with trigger in stock? Tried to set my dwell Tried to set my binary but it doesn’t work…
@@KennyDope6 I am running the stock spring with all three of my SI units and haven't seen that issue yet. But if it works then it's all good. I know some people have seen issues and have gone for the ring mod (replacing the spring with a stack of o-rings) The board should be available for sale soon, I just got a production board and I'll do a video on it soon for installation purposes. The Gorilla site should be going live soon too.
Thanks for your explain, tips and tricks! It help me further to make my dreambuild! Do you also know what handguard it wil fit the Article? Want a longer handguard with a shorter outerbarrel so my tracer is build in my handguard!
@@KennyDope6 You are welcome. I had the Mac Speed soft stuff on mine for a bit. But moved it over to my MTW as it needed some love too. He has a few different handguard options and an Article 1/MTW specific outer barrel. I have the UL M-Lok LX and the quality is awesome.
Do you want to add the Maxx selector switch or remove it completely to replace it? To add the Maxx just remove the hex screw, to remove the whole selector you will need to remove the grip as there is a pin and spring that secure it in place.
@@KennyDope6 They generally use Loctite or similar brand of thread lock on some of their parts. You need to remove the entire thing and heat it up with a heat gun. This will soften it enough to allow you to remove it. Alternatively you can use a hair dryer, but it will take quite a while to reach the correct temps. I wouldn't recommend using a direct heat source such as an open flame.
![The one where I got my own Article 1 [Airsoft - Heretic Labs Article 1 gameplay]](/img/1.gif)
The Gorilla mMTW board is now available!
Check out Mac Airsoft (EU) - www.mac-airsoft.it/hpa/electronics/gorilla/
Airsoft Armourer (UK) - airsoftarmourer.co.uk/product/gorilla-mmtw/
I will add a US store once starts stocking them!
I would love to see you do a review on the Article II that just came out.
You've made very good content for a niche product, subbed!
It's def on the list, I am just waiting for the store where I live to import them (stupid German laws).
I like that they have gone for a longer barrel on the II, those few extra mm will allow for better fps for those playing outdoors.
Thanks for making these. Not enough content out for the Article 1 and potential upgrades as it's so new.
Thanks for watching.
I will be doing a few more Article 1 videos. I also have some tech videos lined up specifically on the Article 1. Plus a few on the MTW line as a whole.
Get it
Sehr schön!
Beste Grüße
Chris
can you make a video shooting it i am also considering this hop up unit
Just got back from a larger outdoor event and was shooting it there, so expect that video soon.
Gorilla grips work on mtw now?
Yes, they brought out an MTW version.
It's on the Mac Speedsoft site, but I'm not sure if any retailers have it in stock yet in the US.
Hey I want to buy the gorilla fcu but none of them look like the one you show in the video. They all look like it won’t fit in my article
Yo, the one I have is the mMTW board, currently the only place I know where to get one is directly from Gorilla. Their site is a WIP and should go live soon. However, you can message him directly on instagram (airsoft.gorilla) and he should be able to sort you out with the mMTW board and trigger.
Or you can message MAC Speedsoft and ask him about the mMTW. He currently only has the mFCU and mini-FCU listed on his site, but he can definitely organize the mMTW board for you. Gorilla and MAC work very closely together on many projects and just released the QCU (Quick Carbon Upper) together.
Hey Max would to ask you , how much ft/s (max and min) your customed Article have?
Hey, we use joules where I live and always measured with actual BB weight. But technically if I use the conversion chart and .20s as a reference I have gotten it down to under 250fps and as high as 440fps. But to get it to 440fps I had to crank up the dwell and the reg was at 140psi to get it there. I don't think the stock board can even get to that dwell.
Im having issues with my article 1 speedqb when i plug the battery in and pull the trigger it doesnt fire, no click or anything. I think my trigger board is broken
It's more than likely that the screws have been set incorrectly, the pressure on the board changes once you put it back together again. Screw in the activation screw for the microswitch and reassemble the gun to see if it is finally activates when assembled.
@@AirsoftMax-EU hey, thanks for the reply. How far do I screw it in, or do I screw it out ?
@@s0ap834 screw it in, I would start with half a turn at a time until you can get it to shoot when the gun is fully assembled again.
Hey Max, I just also installed the Silent ind. hop up chamber but it’s Not so springy when I put it in my Outer barrel! What I’m doing wrong?
Hey, do you have the original spring installed that came with the Article 1?
@@AirsoftMax-EU I installed the OG spring! But I think it’s solved maybe too much paint on the chamber it was jamming on the barrel nut there is a little paint off but springy now!!!
And when comes that Gorilla FCU with trigger in stock? Tried to set my dwell Tried to set my binary but it doesn’t work…
@@KennyDope6 I am running the stock spring with all three of my SI units and haven't seen that issue yet. But if it works then it's all good. I know some people have seen issues and have gone for the ring mod (replacing the spring with a stack of o-rings)
The board should be available for sale soon, I just got a production board and I'll do a video on it soon for installation purposes. The Gorilla site should be going live soon too.
Thanks for your explain, tips and tricks! It help me further to make my dreambuild! Do you also know what handguard it wil fit the Article? Want a longer handguard with a shorter outerbarrel so my tracer is build in my handguard!
@@KennyDope6 You are welcome.
I had the Mac Speed soft stuff on mine for a bit. But moved it over to my MTW as it needed some love too.
He has a few different handguard options and an Article 1/MTW specific outer barrel.
I have the UL M-Lok LX and the quality is awesome.
Can you disassemble the selector switch by take off the hex screw?
Do you want to add the Maxx selector switch or remove it completely to replace it?
To add the Maxx just remove the hex screw, to remove the whole selector you will need to remove the grip as there is a pin and spring that secure it in place.
@@AirsoftMax-EU Thanks for your answer want to replace it for the Maxx selector but they tighten the hex screw!
@@KennyDope6 They generally use Loctite or similar brand of thread lock on some of their parts. You need to remove the entire thing and heat it up with a heat gun. This will soften it enough to allow you to remove it. Alternatively you can use a hair dryer, but it will take quite a while to reach the correct temps. I wouldn't recommend using a direct heat source such as an open flame.
@@AirsoftMax-EU Ok, I’ll give it a try, thanks again keep dropping your Atricle 1 content!!!
@@AirsoftMax-EU Thanks bro the screw came loose EZ!!!