Видео

I usually don't play with any optics as I prefer playing with a line of sight style like from paintball. But I have been testing out the Novritsch 3x Prism Scope and the Sig Romeo5 red dot. The prism scope has been more for checking targets at longer distances.

No, it doesn't come with a battery. You will need to buy a 7.4v 250-350mAh Lipo battery, it will need to be a battery with a JST connector (this is the standard connector for HPA guns). The Titan batteries are really good, but are slightly too long, so I would not recommend them. US: www.airsoftjunkiez.com/hpa-fcu-lipo-7-4v-300mah-30c-battery/ www.evike.com/products/37904/ ampedairsoft.com/hpa-mini-lipo-7-4v-mini-lipo-battery-250mah-jst/ EU: www.powair6.com/en/hpa-battery/51305-gens-ace-250mah-74v-35c-lipo-battery-jst.html www.airsoftstore.be/en/74v-lipo-300mah-35c-70c-hpa.html www.gensace.de/gens-ace-250mah-7-4v-35c-2s1p-airsoft-gun-lipo-battery-with-jst-syp-plug.html www.mac-airsoft.it/hpa/electronics/hpa-lipo/

@@AirsoftMax-EU ok thank you i really appreciate it thanks again

@@juztkiah You're welcome

Hey, we use joules where I live and always measured with actual BB weight. But technically if I use the conversion chart and .20s as a reference I have gotten it down to under 250fps and as high as 440fps. But to get it to 440fps I had to crank up the dwell and the reg was at 140psi to get it there. I don't think the stock board can even get to that dwell.

I use a mix of PTS EPM1 and EPM1s mags. They are pricey, but worth the price. But there are loads of decent mags on the market. Apparently, the Lancer Tactical mags are not half bad (the speedsoft ones).

@@AirsoftMax-EU I too am running the same mags and same gun, I was just recently playing last weekend and I was getting a lot of inconsistent feeding

@@mardymarc_ yeah, so there is an issue with the mags dropping slightly and then not feeding properly. It's super annoying as it affects both of my Article 1s and not my MTWs. What I did was print a spacer that fits between the internals of the mag and the body. This lifts it up slightly to allow the mags to feed properly. Another solution is to add a bit of velcro to the inside of your magwell to keep the mag firmly in place.

Ne, ist eine Speedsoft Waffe vom Hersteller Wolverine (MTW). Ist die Article 1 mit einem Griff für die Flasche, so schaut nur aus wie einen Paintball Markierer. Waren eigentlich 4 Teams + LARPers. Rot, Gelb und Blau als reguläre Teams und dann Schwarz als Sondereinheit Team. Die Jungs von Team Schwarz habe ich nur einmal gesehen. und nach 5min waren die wieder weg. Blau haben wir auch nicht so oft gesehen, aber da waren paar blaue Hits im Video dabei. Die LARPers haben extra Missionen ausgeteilt und man sollte die nicht angreifen. Die wurden von gelben Spielern angegriffen und wir waren zufällig da. So, Gelb hat dann Minuspunkte bekommen und wir haben dafür Bonuspunkte gesammelt.

@@AirsoftMax-EU danke für die Erklärung!

@@intheshadows1623 Gerne

@@AirsoftMax-EU Dafür hatte ich am zweiten Tag ganz zu Anfang mit der Schwarzen Truppe zu tun, mein Auftrag war ja, den Sprengmeister🤠 mit einem Kleinen Trupp im Tiefbunker einzusammeln und ins HQ zu geleiten bevor die Gelben auftauchen. Netterweise hat sich die Orga gedacht, dem geben wir Team Schwarz als Leibwache dazu (😁🤭) und lassen die bei Spielstart natürlich bereits im Bunker Spawnen😇. Und ich sage noch auf Maschas Frage: "Wieviel Leute brauchst du?" "Ja so 4-5, falls wir den Gelben begegnen, damit wir genug Feuerkraft haben um uns mit Ihm abzusetzen." Ich habe gefühlt 40 Leute und ne Halbe Stunde gebraucht, und dann hat nen dulli🥴 eine Flashbanggranate😵‍💫 zu dem Spengmeister hinein und hinuntergeworfen und ihn Quasi weggesprengt!😵 Man war der Sauer, hat uns leider auch Strafpunkte gekostet!😳 Hätte nicht sein müssen. Zunächst dachten wir auch alle, die Mission ist damit vorbei, doch Glücklicherweise Spawnte der Sprengmeister immer da, wo man ihn hittet durch erneutes Anfassen an der Schulter (Puhh, glück gehabt). Aber ernsthaft, die Schwarzen waren richtig harte gegner, hut ab und danke an euch Jungs. 😎Die Gelben tauchten im übrigen in der Zeit nur 1 mal kurz in der Nähe des Tiefbunkers auf. Zu den Cheatern, ich bin dafür, dass die in zukunft, wenn Sie Cheaten wollen, den Cheatcode Also die ganzen Dreiecke, Kreise, Quadrate und Kreuze zunächst der Orga Vorttanzen, wenn die Orga sagt, Code Korrekt, darf er weitemachen, da ist Spawnen deutlich schneller.😁

Ja genau da haben wir die gesehen, hab 3 Rausgeschossen und dann war Schluss mit Team schwarz für uns. Die haben es halt mit die Nummern versucht, aber ganz oft warn die Laute einfach zu weit weg um die nummer zu erkennen, oder du musstest hin laufen wie ein Depp und nach denen Nummer nachfragen. War keine Güte Lösung.

ja, sie benahmen sich einfach wie schlecht erzogene Kinder.

That's ramping mode, it's a mode from paintball and is one of the features of the Gorilla boards.

@@AirsoftMax-EU Daaaaaiiiuuuummm bro I can’t wait for those bad ass board release

@@KennyDope6 I already got a production board, busy shooting the install video for it ;) The board should be hitting stores really soon. Such a game changer!

@@AirsoftMax-EU I know but my og board does some weird things done with it, waiting for some Gorilla power!!!

@@KennyDope6 get that Gorilla goodness in your gun.

Hey, do you have the original spring installed that came with the Article 1?

@@AirsoftMax-EU I installed the OG spring! But I think it’s solved maybe too much paint on the chamber it was jamming on the barrel nut there is a little paint off but springy now!!! And when comes that Gorilla FCU with trigger in stock? Tried to set my dwell Tried to set my binary but it doesn’t work…

@@KennyDope6 I am running the stock spring with all three of my SI units and haven't seen that issue yet. But if it works then it's all good. I know some people have seen issues and have gone for the ring mod (replacing the spring with a stack of o-rings) The board should be available for sale soon, I just got a production board and I'll do a video on it soon for installation purposes. The Gorilla site should be going live soon too.

Thanks for your explain, tips and tricks! It help me further to make my dreambuild! Do you also know what handguard it wil fit the Article? Want a longer handguard with a shorter outerbarrel so my tracer is build in my handguard!

@@KennyDope6 You are welcome. I had the Mac Speed soft stuff on mine for a bit. But moved it over to my MTW as it needed some love too. He has a few different handguard options and an Article 1/MTW specific outer barrel. I have the UL M-Lok LX and the quality is awesome.

Yo, the one I have is the mMTW board, currently the only place I know where to get one is directly from Gorilla. Their site is a WIP and should go live soon. However, you can message him directly on instagram (airsoft.gorilla) and he should be able to sort you out with the mMTW board and trigger. Or you can message MAC Speedsoft and ask him about the mMTW. He currently only has the mFCU and mini-FCU listed on his site, but he can definitely organize the mMTW board for you. Gorilla and MAC work very closely together on many projects and just released the QCU (Quick Carbon Upper) together.

Before, and 3 seconds after as well

Before, it's meant to be a sort of replay cam. So if you make a dope shot and want to capture it you just need to make sure you press it quickly enough. My clips are all 17sec long, but a team mates are all 16sec long.

@@AirsoftMax-EU thank you! I ordered my clipcam, can’t wait until its delivered so i can film my kills more professionally

@@AirsoftMax-EU i just did my first recording with it! I uploaded it on youtube. The camera works fine!

It's more than likely that the screws have been set incorrectly, the pressure on the board changes once you put it back together again. Screw in the activation screw for the microswitch and reassemble the gun to see if it is finally activates when assembled.

@@AirsoftMax-EU hey, thanks for the reply. How far do I screw it in, or do I screw it out ?

@@s0ap834 screw it in, I would start with half a turn at a time until you can get it to shoot when the gun is fully assembled again.

Yeah, I already took it apart ages ago and replaced the SD card. Though it 100% voided my warranty.

Hey hey, yeah I remember seeing you at the event, that GBB Thompson is so so cool, such a unique gun. What brand is it?

@@AirsoftMax-EU Is the Wei-ETech Thompson M1A1 Vollmetall Gas-Blow-Back 6mm BB schwarz / braun

@@Yvonne_Berning nice, it's always nice seeing different guns on the field, especially WWII GBBRs. I saw a guy with a GBBR Sten at AO last year, which is also very cool to see.

Do you want to add the Maxx selector switch or remove it completely to replace it? To add the Maxx just remove the hex screw, to remove the whole selector you will need to remove the grip as there is a pin and spring that secure it in place.

@@AirsoftMax-EU Thanks for your answer want to replace it for the Maxx selector but they tighten the hex screw!

@@KennyDope6 They generally use Loctite or similar brand of thread lock on some of their parts. You need to remove the entire thing and heat it up with a heat gun. This will soften it enough to allow you to remove it. Alternatively you can use a hair dryer, but it will take quite a while to reach the correct temps. I wouldn't recommend using a direct heat source such as an open flame.

@@AirsoftMax-EU Ok, I’ll give it a try, thanks again keep dropping your Atricle 1 content!!!

@@AirsoftMax-EU Thanks bro the screw came loose EZ!!!

Very simple answer, the Gate Titan II is a V2 only board, there is no way to get it to fit in or work with the Article 1 as it does not have a gearbox. I do own a handful of Titan IIs that I use in some other builds though.

I was one of the two guys running the paintball looking guns. It was a fun event, minus the mass cheating from the yellow team. The blue team were honest and called their hits every time.

Just got back from a larger outdoor event and was shooting it there, so expect that video soon.

According to Wolverine/Heretic Labs it should hit up to 1.65j (420 FPS) out of the box with .20g. But I have never hit 420 FPS with a stock Article 1. I got around 380 FPS with mine, which is playable for outdoors and way over for indoor play. The newer Article II comes with a longer inner and outer barrel, which will allow you to achieve higher FPS.

It's def on the list, I am just waiting for the store where I live to import them (stupid German laws). I like that they have gone for a longer barrel on the II, those few extra mm will allow for better fps for those playing outdoors.

Die Videos sind eigentlich recht klein, etwa 27 MB pro Clip. So, du kannst eine ganze Reihe von Clips auf dem 30-GB-Speicher unterbringen. Aber, ja, mehr Speicher wäre besser.

@@AirsoftMax-EU Die lässt sich recht einfach zerlegen, im inneren findet man eine handelsübliche microSD Karte, problemlos erweiterbar auf 64GB

​@@KGKolibri ich hab meins schon längst aufgemacht und hab eine 64GB Karte drin von Sandisk. Mit 32GB wäre es auch kein Thema, da man nicht kontinuierlich filmen kann. Aber mehr ist immer besser und wenn die Garantie eh egal ist, dann kann man die aufmachen.

Thanks, I've been trying to improve a few things and also trying to streamline my workflow a bit so that I can release regular videos. But I am having fun, which is the main thing for me.

i meant switching my aeg speedsoft gun to this gun

The easy of use and out of the box performance make it a winner in my book. Despite some of the minor issues, it's a solid buy if you wan to avoid any alignment issues. I have a couple of V2 and V3 builds and some were perfect first time, and some took a bit of time to get running flawlessly. But, if you already have an AEG they are the cheaper option. The Jack is a decent engine, and you can take it out and put it into the next gun.

Thanks for watching. I will be doing a few more Article 1 videos. I also have some tech videos lined up specifically on the Article 1. Plus a few on the MTW line as a whole.

Yes, they brought out an MTW version. It's on the Mac Speedsoft site, but I'm not sure if any retailers have it in stock yet in the US.

Thanks, it's the Core Airsoft DSL1 core-airsoft.com/product/dsl1-carbon-fiber-silencer/

Not quite yet. If you are in Europe, then Super5ives has them in stock in the UK. For the US, I'm not sure who has stock right now. You can always email Wolverine, they are pretty decent to deal with and super friendly. Are you doing customizing or did you get a silver gun with a black trigger?

Thanks, still need to work on the production value and getting rid of those "ahs" and "ums". But all in good time.

It's reverse threaded, but if yours has been glued then try heating it up with a heat gun and you will then be able top remove it.

It might just be a simple case of you tested it with the lower and upper separated. The pressure on the board is completely different once you put it back together again. You will need to back out the microswitch screw and see it is works when you put it back together again. If that screw is flush, then the pre-travel screw needs to be backed out a bit (though usually this isn't an issue as the safety should prevent it touching the switch). If it was installed in the gun with a battery connected and you accidentally touched the board with your allen key then you could have fried it. I always make sure the battery is not connected when I make any adjustments.

@AirsoftMax-EU i was using it with battery thinking it would be easier. I might have possiblly hit one of the metal squares on triggerboard, didnt hear anything no smoke or smells. But i put everything back together no response. If the chance it's shorted which it probably is what are my options. Just a new board or can a resolder anything? I havent been able to find a board thats article one by itself. I found the mtw one but not sure compatibility between the systems

@@munchrmx ah yeah that might have done it. It's hard to say which component died if it truly did short. Do you have a multimeter? If yes you can remove the board, put the prongs in the springs (the ones connecting the board to the upper) and you can test if the board sends a current when you push the switch. Alternatively, you can ghetto it and just push the board against the contact yoke on the upper and see if the solenoid activates. The boards are exactly the same, the only difference is the binary mode on the one found in the Article 1. Open up a support ticket with Wolverine and see if they can do anything for you. I have had pretty good experiences with them so far.

@AirsoftMax-EU thanks for the help. Appreciate you taking the time to assist.

Will probably have a look in thr morning and test the board. If not i have friends who are techs who will probably enjoy tinkering with it.

You need a small 250mAh or 300mAh 7.4v battery. It needs a JST connector, which is the standard for all HPA guns.

Yeah, Battleground Paintball Brożek

@@AirsoftMax-EU my fav youtuber plays paintball there.

@@Tacticaltimmy-123 ah nice, who? I played paintball there a few times and will play one of the big games there this year again. It's a dope field with great facilities.

@@AirsoftMax-EU it is @barkerpb I have no idea how he gets his markers from the uk to Poland

@@Tacticaltimmy-123 Traveling with markers is fairly easy, I traveled loads for paintball in the past when I still played speedball religiously.