These engines always have rust on them in door or out 2 I can make a brand new engine look this bad in a week by simply putting rust causing chemicals on them
Tengo un honda de ese modelo,con problemas de carburación solo enciende con el ahogador cerrado y me gasta mucho combustible además no sostiene la baja solo en alta,que será?
This is a Chinese fake, the original engine has a metal timing wheel. Why didn't the mate remove the piston and change the piston rings, the amount of carbon build up that was on the piston shows that the rings didn't exist.
if you didnt replace the piston rings this rebulid was not good. If you want to rebulid an engine take it whole apart i can see that this engine was burning oli only by looking on piston and exust fumes so you have done terible rebulid
That’s the fun of it is to do a rebuild and looks great
это не реставрация а просто чистка!!!
Good job 👍👋👋👍👋
Thanks 👍
Very nice 👍👍👍
Thanks for the visit
Fantastic idea
Thank you! Cheers!
👍👍👍
Wow Excellent work
Thank you so much 😀
Good Stuff
Thanks for the visit
What pad do you use on your angle grinder to get the rust off?
these videos are fake
These engines always have rust on them in door or out 2 I can make a brand new engine look this bad in a week by simply putting rust causing chemicals on them
😊👍
took you long enough to realize it was on full choke, lol good job, good video
Nice job. Little bit to fast move.
Thanks 👍
What did you use on the aluminum to get it that clean? Wire wheel?
Forget a wire wheel. Get a vapor blaster. Convert a a sandblaster to a vapor blaster. It will change your life when rebuilding these engines.
Thanks!
No problem!
Enginee oil?
Why take apart and not replace rings and oil seal?
Tengo un honda de ese modelo,con problemas de carburación solo enciende con el ahogador cerrado y me gasta mucho combustible además no sostiene la baja solo en alta,que será?
too quick but quite good viedo
seria bom trocar os rolamentos novos retentores pistão e molas mais muito bom trabalho
Mi pasión la mecánica Diesel 🙏🙏🙏
It's a petrol engine lol
What type of engine oil should l use to my same motor?
I recommend using 10w30 or 5w30. If your engine is old, like 6+ years, use 10w40 or 5w40. Use fully sintetic oils.
@@Alinushhh i am using 20w50 since my engine is a chinese clone so it doesnt burn oil
Use any oil tbh, its a honda they arent picky. I just use what i have ranging from 5w30 to 10w50. All work fine
In the south 30 w
your telling me this mans has no ratchets
Igualmente
Untuk perawatan berkala Oli mesinnya SAE brp dan kapasitas oli mesinnya brp ml bang? Terima kasih
SAE 10w30, API se,sf, or sg. 600ml
Adonde puedo ir?
So you just didn’t bother setting valve lash.
Okay
If i had slow motion this might be worth watching
This is a Chinese fake, the original engine has a metal timing wheel. Why didn't the mate remove the piston and change the piston rings, the amount of carbon build up that was on the piston shows that the rings didn't exist.
oh thanks you
if you didnt replace the piston rings this rebulid was not good. If you want to rebulid an engine take it whole apart i can see that this engine was burning oli only by looking on piston and exust fumes so you have done terible rebulid
Honda cam mũ á
Honda tàu .
start it on something soft not the concrete
Paano po magtanggal ng cam shaft
Honda with a plastic gear ???
Que pasa si le canbeo las válvulas la de una ala otra de la izquierda a derecha será que se daña
Valve clearance is not correct
Istead of the useles music, why not do some talking?
this is not a honda
Bikin video kyak d buruh setan
This is not honda
why?
@@ksthacks honda do not use plastic elements in engine. This is a copy of honda engine
Bikin video kyak d buruh setan