You don’t screw around when it comes to “how to” videos! That’s great! I don’t know if you’ve seen the hybrid bearing edge that Guru Drums came up with,but I think it would make a noticeable difference on ANY drum and they purposely didn’t patent it so anyone can use it .Beautiful work by the way!
pretty cool, but have you considered mounting one of your end blocks permanently? instead of bending from the middle you slide the board into one end and then bend the full semi-circle from one side. that way you only have to worry about initially clamping the opposite side and not both sides at once.
Hi I've made a steam box I'm getting dissharted as my wood keeps splitting I'm in UK do I just buy wood from saw Mill and should I soak in water I want to make my own drum hoop for a skin I got can uou help ☺️
Dude! Are you growing your hair out again? I'm really looking forward to seeing this project evolve. I like your band saw technique for segmented shells and I'm sure this will be just as enlightening.
Really? Half shells? Most steam bending is done in one piece of wood, not two. You don't have enough clamps, no ropes or cords, no peg holes around the form base. The form itself should have been a full circle, with a notch cut for the final over lap clamping. Where did you learn to do it this way? PS: Just a thought, did you at one time make wood wagon wheels? It looked like you were bending a Felloe or an Ox Yoke. Maybe you used to make Windsor Chairs?
I've never done any steam bending before, just learning as I go. I've been building stave and segmented drum shells for a few years and this was my first attempt at doing steam bent shells. I decided to make the shells with 3 or more rings stacked one on top of the other like a segmented drum, with the butt joints staggered, rather than making the rings in one piece with scarf joints. This is just a little prototype and I already have one Oak shell that is looking good, just haven't finished it off yet. There is a picture of the shell on my Facebook page: facebook.com/MurrayDrums/photos/a.1933326976709853/1933329896709561/?type=3&theater I will be doing more of this in future if I run out of orders for my segmented drums!
It is a great to see him do it. But I am wondering. Why do you fiddle around so much? Why didn’t you just set it and be ready to set it? You had it clamped, then you took the off, then put them on, then took them off, then was not ready with the clamps, then one of the clamps are not functioning. Etc. it was kinda stressful to watch. I was saying to myself.... Geez dude, hurry up and set it and leave it alone before it cools. Lol
You sir are an inspiration. Steaming and bending drums shells in the kitchen. Now I know I’m not crazy for wanting to go and do the same.
Incredible work,I have now been watching your build vids non stop and loving it.You sir are a true craftsman.
10:31 ooooooh🤣.
I wanna try steam forming solid wood shells. It looks like a fun kind of PITA. Nice work!!
You don’t screw around when it comes to “how to” videos! That’s great! I don’t know if you’ve seen the hybrid bearing edge that Guru Drums came up with,but I think it would make a noticeable difference on ANY drum and they purposely didn’t patent it so anyone can use it .Beautiful work by the way!
this would be an excellent way to make RIMS type drum mounts
I see you make half shells. Do you make full shells too?
Your wife must have been ecstatic with how you've repurposed the kitchen. Haha.
Haha, I have a band saw in the living room too... Probably why I will never actually have a wife, lol!
pretty cool, but have you considered mounting one of your end blocks permanently? instead of bending from the middle you slide the board into one end and then bend the full semi-circle from one side. that way you only have to worry about initially clamping the opposite side and not both sides at once.
You could also notch out the metal to then slip the clamps into, and then just pull the metal away when done.
Hi I've made a steam box I'm getting dissharted as my wood keeps splitting I'm in UK do I just buy wood from saw Mill and should I soak in water I want to make my own drum hoop for a skin I got can uou help ☺️
Arent drums supposed to be round?
Two semi circles glued together = 1 circle!
Dude! Are you growing your hair out again? I'm really looking forward to seeing this project evolve. I like your band saw technique for segmented shells and I'm sure this will be just as enlightening.
Nah, it's about time the mane was cut again, I look like Grizzly Adams in this video, lol!
I remember your long, flowing, golden locks. That would suck to get caught in a lathe. You're probably better off with shorter hair.
Never enough hands!
Really? Half shells? Most steam bending is done in one piece of wood, not two. You don't have enough clamps, no ropes or cords, no peg holes around the form base. The form itself should have been a full circle, with a notch cut for the final over lap clamping. Where did you learn to do it this way?
PS: Just a thought, did you at one time make wood wagon wheels? It looked like you were bending a Felloe or an Ox Yoke. Maybe you used to make Windsor Chairs?
I've never done any steam bending before, just learning as I go. I've been building stave and segmented drum shells for a few years and this was my first attempt at doing steam bent shells. I decided to make the shells with 3 or more rings stacked one on top of the other like a segmented drum, with the butt joints staggered, rather than making the rings in one piece with scarf joints. This is just a little prototype and I already have one Oak shell that is looking good, just haven't finished it off yet. There is a picture of the shell on my Facebook page: facebook.com/MurrayDrums/photos/a.1933326976709853/1933329896709561/?type=3&theater
I will be doing more of this in future if I run out of orders for my segmented drums!
It is a great to see him do it. But I am wondering. Why do you fiddle around so much? Why didn’t you just set it and be ready to set it? You had it clamped, then you took the off, then put them on, then took them off, then was not ready with the clamps, then one of the clamps are not functioning. Etc. it was kinda stressful to watch.
I was saying to myself.... Geez dude, hurry up and set it and leave it alone before it cools. Lol
it looks like "German tecnology"... enough...to blow up somebody's mind ...but look's interesting...)))